• Journal of the Korean GEO-environmental Society
• /
• v.22 no.4
• /
• pp.5-13
• /
• 2021

The transition is the zone where support stiffness suddenly increases in the railway industry. If the support stiffness increases, differential settlement will occur at the transition due to difference of stiffness, and the differential settlement causes problems for the train running safety and the roadbed that supports the track. In particular, a study on differential settlement at bridge-earthwork transition was only conducted to considering railway load in most cases. However, these studies have not taken account of earthquake despite earthquake has been occurred frequently in the recent, and it is necessary to consider earthquake. Therefore, in this study numerical analysis has been performed by changing the inclination of approach block, which determines the shape of the transition, and earthwork in order to verify the effect of the shape of the transition on the dynamic behavior at the bridge-earthwork transition. The result shows that the dynamic behavior at the bridge-earthwork transition was affected by the shape of transition.

• Journal of the Korean Society for Railway
• /
• v.13 no.1
• /
• pp.1-8
• /
• 2010

In domestic developing magnetically levitated (Maglev) vehicle, bogie frames install electromagnets which provide the vehicles to run with levitation and guidance forces; moreover, the linear motors used for traction are integrated into the same mechanical structure. This paper presents the process which predicts the evaluation of life cycle for bogie frame on various running conditions. Durability analysis considering vibration effect is simulated by using random loads resulted from dynamic simulation which takes into account the irregularities of guide rail. And it supports additional weak points which were not examined in static analysis.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.586-590
• /
• 2005

In order to compare the dynamic loading effects of particular trains it is necessary to use methodology that separates the two inherent aspects of the dynamic response of the total dynamic system-the characteristics of the train and a bridge. Because the train signature profile is a function of axle spacing and axle loads, it can be calculated which is independent of the characteristics of an individual bridge. Thus the use of the train signature enables a rapid comparison of the effects of different trains to be made. If the magnitude of train signature for a new train type is less than of existing trains on a route then the route will be satisfactory for the new train. This study presents a quantitative analysis of the dynamic loading effects for various domestic real trains-PMC8, PMC16, Mugunhwa passenger coach, several freight coach, KTX and TTX(Tilting Train Express)- Using the train signature.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1996.04a
• /
• pp.111-118
• /
• 1996

Dynamic load models which show the practical behavior of truss bridge subjected to moving train load are presented. Three basically approaches are available for evaluating structural response to dynamic effects : moving force, moving mass, and influence moving force and mass. Simple warren truss bridge model is selected in this research, and idealized lumped mass system, modelled as a planar structure. In the process of dynamic analysis, the uncoupled equation of motion is derived from simultaneous equation of the motion of truss bridge and moving train load. The solution of the uncoupled equations of motion is solved by Newmark-$\beta$ method. The results show that dynamic response of moving mass and static analysis considering the impact factor specified in the present railway bridge code was nearly the same. Generally, the dynamic response of moving force is somewhat greater than that of moving mass. The dynamic load models which are presented by this study are obtained relatively adequate load model when apply to a truss bridge.

• Journal of the Korean Society for Railway
• /
• v.9 no.2 s.33
• /
• pp.137-144
• /
• 2006

The Extradosed PSC bridge is one of the best alternates which not only covers the longer span than PSC box girder and also performs the role of landmark facility with much cheaper cost than cable stayed bridge. Since the cable-stayed long span bridge is more flexible than general medium span bridges and railway bridges can be experienced resonance phenomenon by repeated equidistant axle loading of the train, it is inevitable to consider the dynamic behavior on impact, deflection and so on. In the present study, the dynamic behavior of an Extradosed PSC railway bridge subjected to moving train forces is analyzed. As well as trains which operate in conventional railway tines, KTX train is also considered. For the estimation of dynamic performances of the Extradosed PSC bridge, vertical deflection, accelerations of the slab, end rotation of the girder and impact on pylons and cables are discussed.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.359-364
• /
• 2006

경부고속철도 교량은 대부분 콘크리트교량으로 2@40m와 3@25m의 박스거더교량의 대표적인 형식이다. 일부구간에서 단경간 또는 2경간 연속 50 m 2주형을 갖는 강합성교량이 건설되었다. 연행하는 차륜이 반복해서 통과하는 철도교량은 주기적인 동적하중에 의하여 공진이 발생할 수 있으며, 특히 고속전철이 통과하는 교량은 저속차량이 통과하는 일반철도보다 공진의 발생가능성이 클 뿐 아니라 고속으로 주행하는 열차의 주행안정성 확보를 위해서 엄격한 제한조건을 만족시켜야 하는 엄밀한 동적설계 조건을 갖게 된다. 그러한 조건 중에서 가속도의 제한 규정은 UIC에서 제안된 기준치로서 도상을 갖는 경우에 0.35g이하를 만족시키도록 요구하고 있다. 현재 KTX가 주행하는 교량에서는 일부구간 및 시점에서 규정치를 초과하는 값을 보이고 있는 것으로 계측되었으며, 그 원인 및 대책마련을 위한 연구를 수행하고 있다. 본 연구에서는 그러한 과도한 가속도의 원인 규명을 위한 각종 매개변수 연구와 그 해결책 마련을 위한 연구를 수행하였으며, 경제적이면서도 효과적인 진동저감 방안을 제시하고 있다.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.6
• /
• pp.61-66
• /
• 2008

In railroad operation, turnout is the device designed to provide very critical functions of moving the train to the neighboring rail. It's the only movable section among the rail and track equipment, which has a complicated structure and as rapid movement between the wheel and rail during operation is unavoidable, the safety and the vibration caused by the impact load of the passing train becomes always the major concern. Response to rail vibration tends to vary depending on physical properties of the rail, rail base and the ground, making it difficult to estimate the quantitative outcome through the measurement. Thus, experimental or empirical approach, rather than an analytic method, has been more commonly employed to deal with the ground vibration. To predict the vibration of the turnout, an experimental value and the measured values are applied in parallel to the factors with a high degree of uncertainty. This study hence was intended to compare and analyze the vibration values measured at the crossing part of manganese turnout by type of train and turnout and distance, as well as predict the intensity of vibration generated at the crossing part of manganese turnout when tilting train accelerates.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.3
• /
• pp.39-47
• /
• 2014

In this study, the full scale model tests were performed with track-roadbed system such as Ho-nam high speed railway. The measured data gives good similar a roadbed pressure with equivalent depth to the Odemark's theory. In the case of earth pressures have a under 50 kPa at upper-subgrade applying 330 kN static loading. Results of cyclic loading tests did not differ significantly from those of static loading test. The elastic displacement at HSB layer has a level of 1/100 compared to the 1 mm that it was evaluation criteria for speed up of High Speed Railway. Elastic displacement at subgrade layer was measured a level of 1/175. The dynamic characteristics of track-roadbed with loading frequency level were linearly increased under 35 Hz, while the wheel loading, displacement and acceleration of roadbed were decreased loading frequency above 35 Hz.

• Journal of the Korean Society for Railway
• /
• v.11 no.1
• /
• pp.54-60
• /
• 2008

In the trackbed design using elastic multilayer model, the stress-dependent resilient modulus $(E_R)$ is an important input parameter, that is, reflects substructure performance under repeated traffic loading. However, the evaluation method for resilient modulus using repeated loading triaxial test is not fully developed for practical purpose, because of costly equipment and the significantly fluctuated values depending on the testing equipment and laboratory personnel. The this study, the paper will present an indirect method to estimate the resilient modulus using dynamic properties. The resilient modulus of crushed stone, which is the typical material of sub-ballast, was calculated with the measured dynamic properties and the range of stress level of the sub-ballast, and approximated with the power model combined with bulk and deviatoric stresses. The resilient modulus of coarse grained material decreases with increasing deviatoric stress at a confining pressure, and increases with increasing bulk stress. Sandy soil (SM classified from Unified Soil Classification System) of subgrade was also evaluated and best fitted with the power model of deviatoric stress only.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.6
• /
• pp.27-34
• /
• 2010

Recently, high-speed railway systems have gained increased interest as a means of environmental friendly transportation, and numerous bridges for high-speed railways have been constructed accordingly. However, bridge design for high-speed railways requires more consideration than conventional railway design because fast-moving trains will lead to significant impact on bridge structures. Thus, this research proposes a revised design considering both bridge-rail longitudinal interaction and dynamic effect of trains to ensure stability of fast travelling trains. To validate the proposed design algorithm, numerical analyses are performed and compared using a constructed 250 m long bridge with 5 spans for a high-speed railway. From the numerical results, the proposed optimum design of high-speed railway bridges exhibits the most economic life-cycle-cost (LCC) when compared with several existing design approaches.