• Journal of Environmental Science International
• /
• v.6 no.1
• /
• pp.25-31
• /
• 1997

The variations of gas hold-up, overall volumetric oxygen mass transfer coefficients and liquid circulation velocity in an internal loop reactor were investigated to manifest scale-up effect. The relationship between superficial gas velocity and gas hold-up were found as Ugr = 0.045 $\varepsilon$r in the pilot-scale and Ugr = 0.056 $\varepsilon$r in the bench-scale reactor. The overall volumetric oxygen mass tractsfer coefficient, KLa was slightly increased in the pilot-scale than in the bench-scale reactor. Flow regime was changed from the bubble flow to the churn-turbulent flow when the superficial gas velocity reached to 3.5 - 4 cm/sec in the pilot-scale.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.1
• /
• pp.6-10
• /
• 2010

A measurement of very high torque for track drive unit in construction equipment is usually in difficulties due to the requirement of a torque meter with high capacity, and the limitation of geometry for an experimental set-up. To improve the troublesome problem, a new device was proposed, where a torque transmitted through the torque arm can be measured by load cells attached at each torque arm. The experimental set-up of the new device was carried out in order to measure the torque values for a mechanical feedback type planetary gear box, in which the power flow circulates itself in a closed-loop. The new device enables to measure torque values of 60,000Nm. Additionally, the measured values were estimated statistically in the aspect of their repeatability and reproducibility, so that an acceptable behaviour as a measuring device can be confirmed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.953-957
• /
• 1994

A performance prediction method is presented in this paper for design of a rotating machinery having power split/circulated transmisson with slip elements and planetary gears. And internal power flow patterns of such systems are theoretically analyzed by using mathematical modeling. To estimate usefulness of the designed machinary, geometrical approach has been adopted through the performance locus diagram which represents overall characteristics of the system. This gives us complect prediction of the qualitative performane and effects of design factors such as system layout, types and gear ratios of planetary gears and disign parameters of slip elements. The results for one of them are compared with experimental ones using dynamometer for verification.

• Analytical Science and Technology
• /
• v.5 no.2
• /
• pp.1096-1113
• /
• 1992

분자구조, 동력학, 그리고 분자들의 화학분응에 관한 정확한 지식은 분자들의 기능과 성질을 이해하는 데 중요한 정보를 제공한다. 2D NMR 분광법의 개발은 용액상의 분자들에 관한 이러한 의문을 해결하는 데 결정적인 역할을 하게 되었다. 그동안 아주 다양한 NMR기술들이 개발되어 왔으며 현재 그들에 대한 이용이 활발하게 진행되고 있다. 그러나 성공적인 2D NMR 분광법의 적용을 위해서는 적당한 기계뿐만 아니라 실험실의 정확한 선택 및 최적 조건의 변수들을 선택해야 하며 스펙트럼의 세밀하고도 정확한 해석을 필요로 한다. 곱연산자 방식(product operator formalism)의 도입은 펄스 FT NMR 분광학을 정성, 정량적으로 이해하도록 하는 것을 가능케 했으며, 이번 해설은 연속적으로 주어지는 펄스의 이해를 위해서 필요로 하는 상의 순환(phase cycle) 및 곱연산자 방식을 이용하여 다양한 2D NMR 기술의 이해를 돕고, 분석기기로서 2D NMR 분광법이 널리 사용 및 활용되어지고자 하는 데 목적이 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.3
• /
• pp.211-216
• /
• 2015

Large hydraulic excavator weighted 90 tons used the several pumps installed in parallel to use the hydraulic pump driving gearbox to improve fuel consumption by improving the energy efficiency of the hydraulic system. Gearbox connected to hydraulic pump supply the mechanical output to the high pressure and low pressure pump to be supplied by torque and rotation, which are the mechanical power, through a input shaft connected to large size engine of the excavator. So, gearbox connected to hydraulic pump is same as main artery in the human body and is required long life because it operates the hydraulic pump continuously during operating the engine. This study had used oil contamination analysis method to check the wear characteristics of the gearbox and frequency response characteristic analysis method to check the failure of the teeth failures of gearbox, while the test equipment adopted by the electrical feedback method to reduce the energy consumption was operating for the life assessment, in which the required power was 600 kW input power.

• Journal of Power System Engineering
• /
• v.19 no.3
• /
• pp.16-21
• /
• 2015

Nitrous oxide($N_2O$) concentration in the atmosphere has been constantly increased by the human activities with industrial growth after the industrial revolution. One of factors to increase $N_2O$ concentration in the atmosphere is the $N_2O$ emission caused by the combustion of marine fuel. Especially, a sulfur component included in marine fuel oils is known as increasing the $N_2O$ formation in diesel combustion. Form this point of view, $N_2O$ emission from a ship is not negligible. On the other hand, Exhaust gas recirculation(EGR) that have thermal, chemical and dilution effect is effective method for reducing the NOx emission. In this study, an author investigated $N_2O$ reduction by using EGR on a direct injection diesel engine. The test engine was a 4-stroke diesel engine with maximum output of 12 kW at 2600rpm, and operating condition of the engine was a fixed load of 75%. The experimental oil was a blend-fuel that were adjusted with sulfur ratio of 3.5%, and EGR ratio of 0%, 10%, 20% and 30%. In conclusion, diesel fuel that contained 3.5% sulfur component increased $SO_2$ emission in exhaust gas, and increment of EGR ratio reduced NO emission. Moreover, $N_2O$ emission was decreased as over 50% at EGR ratio of 10% and reduced 100% at EGR ratio of 30% compared with $N_2O$ emission of 0% EGR ratio.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.733-738
• /
• 2013

Sediment contains a high fraction of organic matter, high buffering capacity, and a large portion of fine grained particles such as silt and clay, which are major barriers to remove heavy metals from sediments. In this study, a lab-scale electrokinetic (EK) technique was applied to remove heavy metals effectively from marine sediment at a constant voltage gradient of 2 V/cm. A concentration of 0.1 M of ethylenediaminetetraacetic acid (EDTA), citric acid (CA), $HNO_3$, and HCl were circulated in the cathode, and tap water was circulated in the anode. CA extracted 92.4% of Ni, 96.1% of Cu, 97.1% of Zn, and 88.1% of Pb from marine sediment. A higher voltage gradient enhanced the transport of citrate and EDTA into the sediment and, therefore, increased metal extraction from the marine sediment through a complexation reaction between metals and the chelates. Based on these results, the electrokinetic process using a high voltage gradient with EDTA and CA might be useful to extract heavy metals from marine sediment.

• Journal of Power System Engineering
• /
• v.18 no.2
• /
• pp.5-11
• /
• 2014

The purpose of this study is to investigate the specific characteristics of combustion and exhaust emissions on a 4-cylinder common rail diesel engine as EGR rate and the rate of blended bio-diesel was altered. Bio-diesel fuel which is a sort of alternative fuels can be adapted to diesel engine directly without modifying. This study was performed to 2000rpm of engine speed with torque 30Nm while EGR rate and the rate of blended bio-diesel was changed. Decreasing combustion pressure and increasing the rate of heat were occurred when we had changed the EGR rate on the 20% of bio-diesel blended diesel fuel. The maximum pressure of combustion and the IMEP became higher as the EGR rate and the rate of blended bio-diesel were changed. Exhaust gas temperature was increased the higher rate of the blended bio-diesel under the fixed EGR rate. However, it went down as the EGR rate increased. The amounts of CO and Soot were reduced with increasing the rate of the blended bio-diesel without changing EGR rate and raised with increasing of the EGR rate. On the fixed EGR rate, NOx was increased along with growing the rate of the bio-diesel. On the other hand, it was decreased while EGR rate were going up.

• Korean Journal of Agricultural Science
• /
• v.19 no.1
• /
• pp.91-96
• /
• 1992

Diesel engine being used on power tiller has over heating problem while running at the rated power range, The reason for overheating the engine is mainly owing to so small capacity of cooling system. This study was conducted to determine relatively optimum capacity of cooling system for the diesel engine. The results obtained are summarized as follows. 1. The capacity of cooling system for the diesel engine being used in the rural area was not sufficient to cool the engine at the rated power. 2. It is desirable that the cooling water flow rate was $12{\ell}/min$ if we used supplementary pump for increasing the cooling efficiency. 3. As cooling water was circuited $12{\ell}/min$, highest temperature of cooling water was $91^{\circ}C$. This value is within $88^{\circ}C{\pm}5^{\circ}C$ of SAE Standard criterion.

• Journal of Biosystems Engineering
• /
• v.7 no.2
• /
• pp.57-71
• /
• 1983

마찰식 정미기의 성능에 영향을 미치는 기계설계 및 작동상의 인자로는 스크린의 형태, 롤러의 형태, 롤러회전속도, 출구 저항 등 여러가지가 있다. 이러한 요인들에 대한 연구가 본 논문의 저자에 의해서 시리즈로 연구되어 왔으며, 본 연구는 그의 일환으로 스크린의 단면형상(6각, 8각, 12각 그리고 원통형), 스크린에 뚫려있는 슬랏의 기울기($15^{\circ}$, $30^{\circ}$, $45^{\circ}$ 그리고 $-45^{\circ}$), 그리고 출구 저항이 정백미의 질과 양, 정백효율 그리고 정백실내의 정백압력 등에 미치는 영향을 규명하기 위해 수행되었다. 이 실험에 사용된 공시 정미기는 임도정 공장에서 널리 사용되고 있는 흡입마찰식이었며, 사용된 시료는 밀양 23호인 통일계품종이었다. 각 처리마다 동력 소모량과 정백실내의 정백압력을 측정하기 위해서 "KYOWA" 스트레인 게이지 시스템(strain gauge system), 토오크 변환기, 압력변환기 등이 사용되었다. 본 실험 결과를 요약하면 다음과 같다. 1) 정백과정중에 정백실내의 정백압력은 입구에서 가장 높았고 출구쪽으로 갈수록 점차 감소하였다. 평균 정백압력도 순환 횟수에 따라서 변화 하였는데 첫번째 순환에서 가장 높았고 순환횟수가 증가함에 따라 감소하였다. 2) 본 실험에서 사용한 출구저항 수준은 출구저항 수준 1에서 요구되는 정백도의 백미를 얻기 위한 순환 횟수는 2회 이었고 출구저항 수준 2에서는 4회 이었는데, 이를 출구저항 수준이 정백압력, 정백율, 완전미수율 및 도정 효율에 가장 큰 영향을 주었다. 3) 스크린에 뚫려있는 슬랏 각도가 $15^{\circ}$에서 $45^{\circ}$로 증가함에 따라서 정백실내의 평균 정백압력은 감소하였고, 완전미수율과 도정 효율은 증가하였으나, 일반적으로 도정수율은 감소하는 경향을 보였다. $-45^{\circ}$의 슬랏 각도를 가진 스크린에서는 슬랏 각도 $15^{\circ}$인 스크린에서와 거의 비슷한 정백압력 수준을 나타냈으나 완전미와 정백미의 생산은 매우 낮았다. 4) 스크린 표면에 기다란 강편 (보통 "띠"라고 부름)을 붙인 원통과 12각형의 스크린에서는 강편을 붙이지 않은 6각형과 8각형 스크린에서 보다는 비교적 높은 정백압력을 나타냈다. 전자는 후자에 비해서 정백효율은 높았으나 완전미수율은 떨어졌다. 5) 정백실내에서 가장 낮은 정백압력을 나타낸 8각형 스크린은 높은 도정수율과 완전미수율을 가져왔으나 상대적으로 정백효율은 낮게 나타났다. 6) 정백실내의 반경 방향의 평균 정백압력($P_R$)과 완전미수율($Y_h$)은 다음과 같은 1차적인 역비례 관계가 있었으며(평균 정백압력 범위는 0.5-0.9kg/$cm^2$), $Y_h=-28.661P_R+84.860$ ($r^2=0.858$) 정백효율($Y_e$)과 정백압력($P_R$) 사이에는 다음과 같은 2차적인 관계가 존재함을 알 수 있었다. $Y_e=-597.5P_{R^2}+929.96P_R-210.15$ ($r^2=0.759$) 정백효율은 정백압력이 0.7-0.8kg/$cm^2$일 때 가장 높았으며, 이때 변이도 가장 심한 것으로 나타났다.