• The Journal of the Acoustical Society of Korea
• /
• v.32 no.2
• /
• pp.104-115
• /
• 2013

In a shallow water waveguide, reverberation signals and their Doppler effects form the primary limitation on sonar system performance. Therefore, in the reverberation-limited environment, it is necessary to estimate the reverberation level to be encountered under the conditions in which the sonar system is operated. In this paper, high-frequency reverberation model capable of simulating the reverberation signals received by a high-speed moving source in a range independent waveguide is suggested. In this model, eigenray information from the source to each boundary is calculated using the ray-based approach and the optimizing method for the launch angles. And the source receiving position changed by the moving source is found by a scattering path-finding algorithm, which considers the speed and direction of source and sound speed to find the path of source movement. The scattering effects from sea surface and bottom boundaries are considered by APL-UW scattering models. The model suggested in this paper is verified by a comparison to the measurements made in August 2010. Lastly, this model reflects well statistical properties of the reverberation signals.

• Journal of Acupuncture Research
• /
• v.29 no.4
• /
• pp.105-111
• /
• 2012

Objectives : An objective measurement for the effects of acupuncture therapy had been regarded as one of the important agendas in the research of acupuncture. This case report aimed to measure the changes of blood flow on the skin flap after one session of electroacupuncture treatment. Methods : A 27-year-old male patient was treated with ipsilateral or contralateral electroacupuncture on the $LI_{11}$, $LU_{10}$, $LI_{10}$, $TE_5$, $SI_3$ and Ex- $UE_9$(Palsa) in the arm with the skin flap on dorsal region of the hand. Changes of blood perfusion on the skin flap and opposite dorsum of hand were measured with laser Doppler blood perfusion imager(LDPI). Results : Immediate post-treatment relative changes of the blood perfusion on the skin flap and opposite hand after one session of ipsilateral electroacupuncture was 21% and 18% higher than values from pre-treatment assessment, respectively. On the contrary, when needled contralaterally, relative changes of the blood perfusion on the affected and unaffected hand was 7% lower and 22% higher than values from pre-treatment assessment, respectively. Mean differences of the blood perfusion between on the skin flap and on control hand remained similar after the ipsilateral acupuncture treatment but substantially increased(44.58 of perfusion units). Conclusions : Electroacupuncture may alter the local blood flow on the skin flap. More study is needed to investigate the effects of acupuncture on the blood flow and microcirculation on the skin tissue by well-designed clinical and experimental studies.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.701-713
• /
• 2009

This paper studies a method for reducing performance degradation due to losing sub-carrier orthogonality caused by power transient between physical channels in LTE uplink transmission. The pattern of inter-carrier interference(ICI) caused by power transient is different from what has been studied for doppler shift, in that its pattern occurs at front and rear sides of channels in each period of power transient. The reason of ICI's occurrence results from power difference between channels, power transient duration, multi-path channel delay spread, and numbers of sub-carrier. New criterion is proposed to find out number of taps of multi-tap equalizer enough to improve the ICI. The scheme is to determine the number of taps of multi-tap equalizer when a normalized interference or a normalized ICI is greater than a normalized noise. Simulation results show that the number of taps is flexibly adjusted according to SNR(Signal to Noise Ratio) of a received signal to improve Bit Error Rate(BER), while the complexity of the proposed scheme is reduced down to 88 percentage of the classical method.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.242-246
• /
• 2006

최근 들어 전 세계적으로 유량측정 분야의 큰 변화의 방향은 자동화이다. 전자, 전기 기술과 정보통신 기술의 발달을 유량측정 분야에 적용하여 자동적으로 유량측정을 수행하고 실시간으로 모든 유량자료를 수집하는 시스템을 구성하려는 연구가 활발하게 진행중이다. 최근에 초음파 유량계와 더불어 자동 유량측정 기법으로 각광을 받고 있는 기법이 유속지수법(index velocity method)이다. 유속지수법의 원리는 매우 간단하다. 수위 기록을 통하여 수위-면적 관계로부터 흐름 단면적을 구하고, 임의의 영역에서 측정된 유속이 단면 평균 유속으로 환산될 수 있다면, 흐름 단면적과 평균 유속에 의해 연속적으로 유량을 구할 수 있다. 유속지수법에서 가장 중요한 것이 전체 평균 유속을 대표할 수 있는 유속지수를 정확하고 효율적으로 측정하는 것이다. 유속지수법에 의한 연속 유량측정 목적으로 최근에 ADVM(Acoustic Doppler Velocity Meter)이 개발되어 이용되고 있다. ADVM은 수중에 초음파를 발사해서 산란체에서 반사되어 돌아오는 초음파의 주파수 편이, 즉 도플러 효과를 이용하여 유속을 측정하는 유속계이다. 본 연구에서는 ADVM을 괴산댐 하류에 위치한 시험하천에 설치하여, 유속지수법에 의한 유량측정기법을 적용하고 그 특성을 분석하였다. 유속지수법으로 측정된 유량을 괴산댐 방류량과 비교한 결과 평균 4.0%의 상대오차를 지니고 있어 비교적 정확한 연속 유량측정이 가능한 것으로 나타났다. 이와 같은 유속지수법을 하천 유량측정에 활용하면 보다 정확한 유량을 연속적으로 자동화하여 측정할 수 있을 것으로 기대된다.연계모형의 한계로 인하여 두 모형의 통합모형이 필요하다. 즉, 강우 혹은 월류유량으로 발생한 지표유량 중 일부분이 과부하가 발생하지 않는 유입구 지점을 통과할 때 배수시스템으로 유입되는 것을 고려할 수 있고, 유입된 유량은 배수시스템 내의 흐름에 반영되도록 배수시스템과 침수해석모형을 통합한 모형 개발이 필요하다. 그러기 위해서는 지표면과 배수시스템에 대한 수리학적 관계를 정립하여야 한다. 본 연구에서는 배수시스템 해석 모형과 도시침수해석 모형을 통합하고, 두 모형간의 유량의 전송과정을 수리학적 관계를 고려한 dual-drainage 도시침수해석모형을 개발하였다. 이를 위해 도시지역 배수시스템 해석 모형으로 널리 이용되고 있는 SWMM모형을 이용하여 지표면으로의 월류량을 산정하고 유입된 지표유량에 대해서 배수시스템에서의 흐름해석을 수행하였다. 그리고, 침수해석을 위해서는 2차원 침수해석을 위한 DEM기반 침수해석모형을 개발하였고, 건물의 영향을 고려할 수 있도록 구성하였다. 본 연구결과 지표류 유출 해석의 물리적 특성을 잘 반영하며, 도시지역의 복잡한 배수시스템 해석모형과 지표범람 모형을 통합한 모형 개발로 인해 더욱 정교한 도시지역에서의 홍수 범람 해석을 실시할 수 있을 것으로 판단된다. 본 모형의 개발로 침수상황의 시간별 진행과정을 분석함으로써 도시홍수에 대한 침수위험 지점 파악 및 주민대피지도 구축 등에 활용될 수 있을 것으로 판단된다. 있을 것으로 판단되었다.4일간의 기상변화가 자발성 기흉 발생에 영향을 미친다고 추론할 수 있었다. 향후 본 연구에서 추론된 기상변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.3
• /
• pp.221-229
• /
• 2013

In this paper, the image formation by the motion compensation technique for Synthetic Aperture Radar system(SAR) were realized through the computer simulation. The motion compensation technique performed image data with the range compression, the compensation procedure, the azimuth compensation and the noise elimination procedure. The range compression procedure transform the SAR raw data into the frequency domain and correlate with the range reference function and then inversely transform into the time domain. The compensation procedure contain the aircraft fluctuations compensation and the radar image degrading effect elimination procedure which was caused by image formation algorithm itself. The aircraft fluctuations compensation procedure perform the first stage which correct the phase angle and the second stage which calculate the Doppler frequency and determine the coordinate of the received signal. The radar image degrading effect elimination procedure also perform range migration compensation and the image defocussing effect compensation. The azimuth compression procedure transform the compensation data to the frequency domain and correlate with the azimuth reference function. The azimuth correlated data are inversely transformed to the time domain which is called SAR image data. When the above procedure were completed, the image data contains the received signals mixed with noise. The threshold technique was applied to elimination the noise from the mixed image data.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.8
• /
• pp.1631-1636
• /
• 2015

With the advance of wireless communication technology in terrestrial area, underwater communication is also evolving very fast from a simple point-to-point transmission to an elaborate networked communications. Underwater acoustic channel has quite different features comparing with the terrestrial radio channel in terms of propagation delay, Doppler shift, multipath, and path loss. Thus, existing technologies developed for terrestrial communication might not work properly in underwater channel. Especially medium access control (MAC) protocols which highly depend on propagation phenomenon should be newly designed for underwater network. CSMA/CA has drawn lots of attention as a candidate of underwater MAC protocol, since it is able to resolve a packet collision and the hidden node problem. However, a received signal could be degraded by the interferences from the nodes locating outside the receiver's propagation radius. In this paper, we study the effects of interference on the CSMA/CA based underwater network. We derived the SNR with the interference using the sonar equation and analyzed the degradation of the RTS/CTS effects. These results are compared with the terrestrial results to understand the differences. Finally we summarized the design considerations in CSMA/CA based underwater network.

• Journal of the Institute of Convergence Signal Processing
• /
• v.13 no.4
• /
• pp.220-232
• /
• 2012

In this paper, we investigate the correlation result due to the problems of delay tracking and fringe rotation module in the VCS(VLBI Correlation Subsystem). The VCS, FX-type correlator, adopts the delay tracking and fringe rotation module in order to compensate the delay change and fringe phase of wave signal from the radio source by Doppler's effect. The phase of observed data is also compensated by means of delay tracking and fringe rotation in the correlator, but we confirmed that the phase is unstable by applying long integration period of AIPS(Astronomical Image Processing System) rather than correlator. And the delay value of observed data has the errors of several tens nanoseconds than normal case at the analysis of correlation result. In addition, we found that the phase of correlation results is not connected as the unit of FFT-segment because the initial fringe phase at the fringe rotation module is not correctly determined. In this paper, in order to solve these problems, the original direction of 90 degree phase jump is reversely modified when the bit-shift occurred at the delay tracking. And the initial fringe phase at the fringe rotation module is correctly modified by using the initial phase of observed data. In addition, the parameter calculation module was abnormally operated as designed in the fringe rotation. So, the logical program by the VCS is modified so as to calculate the parameters correctly. Through the experiments of correlation processing over the above problems, the modified proposal algorithm is adequately corrected to the data analysis results, so that the experimental results make it clear for us to operate the developed VCS hardware correlator normally.

• Journal of the Korean Magnetics Society
• /
• v.25 no.3
• /
• pp.83-86
• /
• 2015

Nowadays the weapon systems are employed air bursting munition (ABM) as smart programmable 40 mm shells which have been developed in order to hit the target with programmed munition that can be air burst after a set distance in the battlefield. In order to improve the accuracy of such a bursting time, by measuring the speed of the munition from the barrel, weapon systems calculate the exact time of flight to the target and then the time information must be inputted to the munition. In this study, we introduce a device capable of detecting a shot at K4 40 mm automatic grenade. The shot is composed of a rotating copper band to convert linear motion into rotary motion when it passes through the barrel, the steel section is exert the effect of fragment and aluminum section to give fuze information. The aluminum section was used to detect munition using eddy current method. To measure muzzle velocity by means of non-contact method, two eddy current probes separated 10 cm was employed. Time interval between two eddy current probe detection times was used as muzzle velocity. The eddy current probe was fabricated U-shape Mn-Zn ferrite core with enamelled copper wire, and 200 kHz alternating current was used to detect inductance change. Measured muzzle velocity using the developed sensor was compared to the Doppler radar system. The difference was smaller than 1%.

• Journal of Korea Water Resources Association
• /
• v.38 no.10 s.159
• /
• pp.811-824
• /
• 2005

The ADCP is an instrument based on Doppler effect, which measures discharge of a river in a short time while crossing it. In this study we aim to make a comparison of the discharge results from a moving-vessel ADCP with those measured by velocity-area method at the same cross-section, and to investigate the characteristics of velocity and discharge data using ADCP. Bathymetry measured by ADCP almost coincides with that by direct depth measurements. Because velocity data from ADCP are essentially instantaneous, individual velocity profiles obtained by ADCP are rather different from time-averaged velocity profiles. But spatially averaged velocity profiles of the individual ADCP data near the comparable verticals have similar vertical velocity pattern with the time-averaged ones. The average velocity profile from repeatedly crossed data is also similar with the time-averaged one. In case of the velocity distribution, individual and spatially averaged data for the sub-width of mid-section method Have good agreement with those by velocity-area method. Discharge data determined by averaging several ADCP measurement transects have $0.1\%{\~}9.3\%$ of difference with those from velocity-area method, and as the number of measurement increases, the relative difference to the velocity-area method decreases.

• Journal of the Korea Convergence Society
• /
• v.10 no.6
• /
• pp.79-87
• /
• 2019

This study examined how the application of silver spike point (SSP) and acupuncture-like transcutaneous electrical nerve stimulation (A-TENS) on acupoints affects blood flow and pain threshold, using laser Doppler blood fluxes and the Commander algometer. Our study included 32 healthy men and women who were randomly divided into the SSP group (n=18) and the A-TENS group (n=14). The pain threshold and blood flow were measured at the Neiguan (PC6) of the Jueyin Pericardium Meridian of the hand. SSP was performed with a 2.8cm electrode at a fixed frequency of 3 Hz for 15 minutes. The change in blood flow and pain threshold after the intervention significantly differed between the two groups (p<0.05). We found that the application of SSP and A-TENS on an acupoint altered their blood flow and pressure pain threshold, with SSP resulting in significantly greater change than A-TENS. Based on these results, the convergence of acupoint and electrical stimulation therapy can be usefully applied as a method for various patients. Continued development of convergence interventions is necessary.