내부순환로의 진출램프 중 성산, 홍은, 홍제, 길음, 마장 진출램프에서는 램프의 지체가 심각하여, 진출차량의 대기행렬이 내부순환로 본선에까지 이르는 대기행렬 역류현상이 발생하고 있다. 이러한 본선으로의 대기행렬 역류는 본선의 혼잡을 가중시키고 교통사고의 위험도 증가시킨다. 본 논문에서는 이러한 도시고속도로의 진출램프 혼잡을 개선하기 위해 진출램프 제어전략을 개발하였다. 진출램프 제어전략의 목표는 진출램프의 대기차량이 본선으로 역류하지 않도록 하는 것이다. 대기행렬의 역류를 막기 위해서는 진출램프의 차량이 인접한 간선도로로 원활하게 진행하도록 해야 하며, 간선도로와 진출램프의 대기행렬을 제어정책에 따라 관리할 수 있어야 한다. 이를 위해서 진출램프 진출부에 신호를 설치하여 간선도로차량의 흐름을 제어하고, 진출부 하류부 교차로와 연동제어를 하여 진출공간을 확보하였다. 또한, 대기행렬의 관리를 위해서는 대기행렬 관리계수를 정의하고 이 값에 따라 현시를 결정할 수 있는 제어식을 유도하였다. 진출램프 제어전략은 과포화 신호제어 기법을 응용하여 개발하였으며, 그 중 Equity offset과 내부미터링 기법을 연동제어에 응용하였고, Imbalanced split 기법은 대기행렬 관리계수에 따라 현시가 결정되는 제어식의 개발에 응용하였다. 진출램프 제어전략을 평가하기 위하여 진출램프의 혼잡으로 인해 본선으로 대기행렬 역류가 발생하는 내부순환로의 홍은, 홍제 진출램프를 선정하였으며, NETSIM을 통해 진출램프 제어전략의 효과를 분석하였다. 분석결과 진출램프의 혼잡이 크게 개선되며, 운영자의 관리목적에 따라 대기행렬의 관리가 이루어지는 것을 볼 수 있었다. 진출램프 제어전략은 내부순환 도시고속도로뿐만 아니라 진출램프 제어가 필요한 타도시고속도로에서도 적용을 하면 좋은 효과를 얻을 수 있을 것으로 예상된다.
Severe congestion is happening at urban freeway off-ramps in Seoul. Major causes of congestion at off-ramps are a shortage of capacity and inefficient signal operations at the downstream intersection at off-ramps. It is necessary to control congestion by improving design or operations in the downstream intersection. In this study, the authors analyzed the case of the Jungdong interchange that was improved for design in the downstream intersection. When a freeway and an arterial road cross, diamond interchanges are usually selected with a single-point urban interchange (SPUI) as an alternative. To compare the effectiveness of a diamond interchange with a SPUI, the authors applied these two configurations to the Jungdong interchange using a simulation. The result of the analysis shows that congestion at off-ramps in diamond interchanges can be reduced by improving signal operations such as the application of "4 phase with overlaps" and that diamond interchanges are more efficient than a SPUI with a frontage road. Efficient operation of the downstream intersection by these findings can minimize congestion of not only the downstream intersection but also the freeway mainline.
KSCE Journal of Civil and Environmental Engineering Research
/
v.30
no.5D
/
pp.467-476
/
2010
Travel delay (TD) denotes a time difference between the running time of vehicle with a normal speed and the travel time of vehicle with a reduced speed for traversing the same segment of roadway, and is sometimes used as a measure of time delayed in the junction or bottleneck areas of roadway. Urban freeways in the foreign countries are often suffering from traffic delay within the entrance and exit ramp junction influence areas, as a freeway with the speed limit of 80 km/h or higher only during the rush hours, but those in our country are especially experiencing severe traffic delay on the mainline segments as well as within the entrance and exit ramp junction influence areas, as a freeway with the speed limit of 80 km/h or less regardless of the rush hours. So, the purpose in this study is to develop the models that could predict the travel delay within the ramp junction influence areas of urban freeway having the geographical features which differ from the expressway, and also examine the validity of the travel delay predictive models developed.
Kim, Tae Gon;Jeong, Young Hwan;Park, Jong Man;Ji, Seung Keun
KSCE Journal of Civil and Environmental Engineering Research
/
v.28
no.2D
/
pp.205-216
/
2008
Urban freeway is defined as the roadway with 4 lanes or more which requires a high design criteria for handling a large capacity of vehicles rapidly as a high-speed exclusive roadway in the city. However, most of the urban freeways suffer from severe traffic congestion due to the increased traffic exceeding their capacities regardless of the morning and afternoon rushhours or the inbound and outbound directions. The purpose in this study is to collect and investigate the real-time traffic characteristics based on the ramp junction influence areas of the urban freeway connected with the Busan port, compare and analyze the traffic characteristic relationship for each lane within the ramp junction influence areas, and finally assess and suggest the optimal capacity for each lane within the ramp junction influence areas.
This paper aims to develop an integrated urban freeway exit-intersection actuated traffic signal control strategy based on which a real-time detection of queue at each of an exit-ramp and an arterial. To evaluate effects of the proposed actuated traffic signal control according to various traffic situations and geometric conditions, this paper analyzed the effects of the proposed traffic signal control strategy according to traffic situations such as the occasion of the arterial being saturated, the occasion of the exit-ramp being saturated, and the occasion of both the arterial and the exit-ramp being saturated. To reflect geometric conditions that influence the effects of the control strategy, this paper evaluated effects before and after applying the actuated traffic signal control strategy according to six cases for both above and under the downstream link length of 200m as proposed by COSMOS. The study results shown that when the link length above 200m, offered a greater effect of applying the actuated traffic control strategy than below 200m. Thus, the actuated traffic signal control through a real-time detection of queue is expected to offer a greater effect at longer downward link.
Kim, Tae Gon;Shin, Kwang Sik;Kim, Seung Gil;Kim, Jeong Seo
KSCE Journal of Civil and Environmental Engineering Research
/
v.26
no.1D
/
pp.59-66
/
2006
This study was to construct the linear density predictive models on the on-ramp junctions in urban freeway. From the analyses of the real-time traffic characteristic data, and the construction and verification of the linear density predictive models, the models showed a considerable explanatory power with the determination coefficients ($R^2$) of over 0.7 between the density and speed data. Also, they showed a considerably high correlativeness with the correlation coefficients (r) of over 0.8 between the calculated density data and the expected ones estimated by the models.
KSCE Journal of Civil and Environmental Engineering Research
/
v.30
no.3D
/
pp.215-222
/
2010
Average speed denotes a travel speed based on the average travel time of vehicles to traverse a segment of roadway, and average travel speed is used as a measure of effectiveness (MOE) suggested in the highway capacity manual (HCM) for evaluating the level of service (LOS) of roadway. Most of the urban freeways in our country are having congestion problem regardless of the rush hours as a high-speed highway with a speed limit of 80km/h or less. Especially traffic congestion within the ramp junction areas is becoming worse by the increased traffic and lack of links with the arterials around the urban freeway. So, the purpose in this study is to identify the traffic characteristics within the ramp junction areas of urban freeway, predict the average speed within the ramp junction areas based on the traffic characteristics identified, and finally prove the validity of the average speed predicted.
A Freeway corridor is a network consisting of a few Primary longitudinal roadways (freeway or major arterial) carrying a major traffic movement with interconnecting roads which offer the motorist alternative paths to his/her destination. Control measures introduced to ameliorate traffic performance in freeway corridors typically include ramp metering at the freeway entrances, and signal control at each intersections. During a severe freeway incident, on-ramp metering usually is not adequate to relieve congestion effectively. Diverting some traffic to the Parallel surface street to make full use of available corridor capacity will be necessary. This is the purpose of the traffic management system. So, an integrated traffic control scheme should include three elements. (a)on-ramp metering, (b)off-ramp diversion and (c)signal timing at surface street intersections. The purpose of this study is to develop an integrated optimal control model in a freeway corridor. By approximating the flow-density relation with a two-segment linear function. the nonlinear optimal control problem can be simplified into a set of Piecewise linear programming models. The formulated optimal-control Problem can be solved in real time using common linear program. In this study, program MPL(ver 4.0) is used to solve the formulated optimal-control problem. Simulation results with TSIS(ver 4.01) for a sample network have demonstrated the merits of the Proposed model and a1gorithm.
고속도로 교통축은 고속도로와 운전자가 대체도로로 이용할 수 있는 표면가로로 구성된 가로망을 말한다. 이러한 고속도로에서의 도로망의 효율을 극대화하기 위해서 시행되고 있는 제어기법으로는 고속도로 진입램프에서의 램프미터링과 표면가로에서의 신호시간조정 등을 들 수 있다. 그러나, 이를 통합한 제어전략은 아직 고려되고 있지 못하다. 고속도로에서 사고나 극심한 혼잡으로 인해 지체가 되었을 경우 단순히 진입램프에서 램프미터링만을 실행하는 것이 아니라 부체도로로의 경로전환을 통해 고속도로교통축의 효율을 극대화할 수 있다. 이는 지능형교통체계(ITS)에서 고려하고 있는 경로안내시스템과도 결부된다. 그러므로, 고속도로 교통축에서는 진입램프에서의 램프미터링전략과 진출램프에서의 경로전환전략, 표면가로에서의 신호최적화전략을 통한 제어를 실행할 수 있다. 따라서, 본 논문에서는 고속도로에서의 진입램프미터링과 진출램프를 통한 경로전환, 표면가로에서의 신호시간조정을 통합한 제어모형을 구축하고, 그에 따른 통합제어알고리즘을 개발하는 것을 본 논문의 목적으로 한다. 통합제어모형은 적정 제어변수의 값을 구하기 용이하게 하기 위해 선형계획법을 적용하였으며, 시뮬레이션을 통해 통합제어알고리즘을 우수성을 검증하였다.
The Journal of The Korea Institute of Intelligent Transport Systems
/
v.12
no.1
/
pp.136-146
/
2013
Truck demand analysis based on TCS data has limitation in that TCS data can not provide truck O/D data for each type of truck vehicle. This study conducted video survey for classifying truck vehicle types. By using TCS data and vehicle ratio by region/cities type, truck O/D data on expressway were estimated. It was found that average travel distances of small truck, medium truck and large truck were 52km/veh, 56km/veh and 97km/veh, respectively by analysing truck O/D data estimated in this study. The reliability analysis showed that check points where error rate is lower than 30% comprise of 87.3%. It is considered that estimated O/D data by truck vehicle types would be useful for the analysis of truck demand of expressway.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.