• 한국생산제조학회지
• /
• 제23권5호
• /
• pp.443-449
• /
• 2014

This study aims to develop a Flywheel Energy Storage System (FESS) that uses wind power produced when an urban train is in motion, by utilizing a mounted turbine. This system was designed to generate and store electric power from wind power of a travelling urban train. The flywheel was designed to continue rotation using a one-way clutch bearing installed in the turbine shaft pulley, even in cases where the urban train decelerates or stops. This FESS can generate an additional 44% of electric power in comparison to a system not equipped with a flywheel. The generated power and operational features of the FESS were evaluated and verified through a wind tunnel test. The results show that the electric power stored in the FESS could supply auxiliary power for urban train components or service equipment, such as charging mobiles, Wi-Fi modules, and electric lights.

• 전기학회논문지
• /
• 제61권9호
• /
• pp.1380-1386
• /
• 2012

It is important to consider supply voltage stability in case of design and construction of a substation at electric railway because a urban transit is operated by electricity and it is driven simultaneous in the same section. This paper study on variation of the dynamic characteristic of supply voltage according to the track environment and spatial distribution as driving of urban transits. Simulation tool, TOM(Train Operations Model) software is used to ensure stability of feeder system being used around the world. As results of simulation, voltage of the contact wire is in limits on driving operation diagram of urban transits. Also, it has confirmed that there is a correlation the phase current, depending on the speed of urban transit and track environment like vertical gradients and curve radius.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.7-18
• /
• 2005

Over the past twenty years, the maintenance system has been developed and its importance has been increased. For the effective maintenance of the urban transit, we have developed the maintenance system based on the concept of RCM(Reliability Centered Maintenance). RCM analysis is a systematic approach to developing a cost-effective maintenance strategy based on the various components's reliability of the system in question. It is performed according to process that includes the following steps; definition of function and functional failures of the systems, construction of RB D(Reliability Block Diagram), performance of FMEA(Failure Modes & Effects Analysis) and calculation of the reliability index. The final process of RCM is to determine appropriate failure maintenance strategies. This paper aims to define the procedure of maintenace based on the concept of RCM for urban transit. The key for a successful maintenance system is an automated scheduling to the maximum extent possible and timely executions. The developed system issues maintenance plan and repair request based on analyzed data and maintenance experience.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.1232-1234
• /
• 2002

In this paper, as a basic study for the production of precisional diagnosis guidelines of the transformer used in railway vehicles, the stress and ageing cause of the transformer is analyzed, the international standards and diagnosis items relative to it are invested and rearanged.

• 한국안전학회지
• /
• 제27권2호
• /
• pp.1-6
• /
• 2012

Uniaxial and biaxial torsional fatigue tests were conducted on the samples extracted from urban railway wheel steel. Ultimate and yield strengths of the steel were 1027.7 MPa and 626 MPa, respectively. The uniaxial fatigue limit was 422.5 MPa, corresponding 67% of the ultimate tensile strength. The ratio of ${\tau}_e/{\sigma}_e$ was 0.63. Fatigue strength coefficient and exponent were 1319.5 MPa and 0.339, respectively. Maximum principal and equivalent strain were found to be adequate parameter to predict fatigue lifetime of the steel under multiaixal fatigue condition.

• 전기학회논문지
• /
• 제63권11호
• /
• pp.1594-1601
• /
• 2014

In this paper, we propose the LQ servo control method for the automatic train control of urban rail vehicle. Structures of the conventional PID control and LQ servo controller are compared in order to demonstrate the simplicity of the proposed controller which doesn't have zeros of the closed loop systems. The energy consumption is dealt with as an object function to be minimized, which consists of the quadratic performance indices for optimal control with the input of the feedback linearization. The effectiveness of the proposed method is shown by the practical example, compared with the conventional PD controller.

• 한국산업정보학회:학술대회논문집
• /
• 한국산업정보학회 2000년도 추계공동학술대회논문집
• /
• pp.367-372
• /
• 2000

국내 도시 철도에 차량 견인용으로 사용되는 전동기는 인버터로 구동되는 200㎾급 3상농형 유도 전동기를 표준 사양으로 선정하였으며 열악한 운전 조건에서도 20년을 상회하는 운전 수명을 보장하도록 규정하고 있다. 그러나 PWM 인버터 구동은 견인 전동기에서 추가적인 고조파 발열 손실과 소음, 진동을 초래하며 더욱이 고속 스위칭에 의한 과도 전압과 빠른 상승 시간을 가진 반복 과전압은 인버터와 전동기를 연결하는 케이블 공진 현상에 의해 배가되어 정현파 구동 시에 예상할 수 없었던 매우 커다란 스트레스를 절연 시스템에 가하게 되어 견인 전동기의 예상 수명에 심각한 영향을 미치고 있다. 따라서 본 연구에서는 인버터 구동 견인전동기의 운전수명을 보장하기 위해서는 기존의 시험 방법에 포함되지 않은 PWM 가변속 구동에 따른 고조파 손실과 과도 전압 충격의 문제점을 고려한 새로운 장기 신뢰성 평가기법이 절실히 필요한 상황이기 때문에 이를 제안하고자 하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.366-368
• /
• 2001

ProfiBus provides real-time data communication among field devices in the EMU(Electrical Multiple Unit) and TCMS(Train Control Monitoring System). This paper presents an adapt to Train Communication Network for EMU using ProfiBus DP(Decentralized Periphery) method, which is the layer 2 DDLM (Direct Data Link Mapper) protocol of ProfiBus.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1454-1456
• /
• 2000

This paper describes the method to develop the ATO software system. The software design is based on VxWorks, a Real Time Operating System. ATO calculates tractive effort/braking effort to keep the train at a certain speed reference at each moment. The speed reference is calculated by the ATO from a number of external factors. The ATO with this software is installed standardized EMU. and tested In Seoul Line 7.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1451-1453
• /
• 2000

The automatic/driverless operation which are great important techniques in metro railway are required to increase higher safety, greater reliability, and transport capacity. To satisfy such demands, we must have the system design and testing technique for the railway system operation. These techniques are related to the onboard train control and communication systems which include TCMS(Train Control and Monitoring System), ATO(Automatic train Operation), ATC(Automatic train Control), and TWC(Train to wayside communication). These sub-systems must be interfacing with not only each others but also the signal system on the ground. We tested the train control system on the 7 line that has been developed on the basis of the standardized type EMU for korea railway systems.