• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.246.1-246.1
• /
• 2010

본 연구는 바이오가스의 에너지효율성을 높이기 위한 연구로서 바이오가스 정제공정과 초저온액화공정을 통하여 액화바이오메탄을 생산하는 바이오가스 고질화기술개발 연구이다. 바이오가스 정제공정은 탈황, 제습, 흡착, 압축, $CO_2/CH_4$ 분리공정으로 구성하고, 초저온액화공정은 열교환기, $CO_2$ 제거설비, 질소냉매 공급공정으로 구성하여 혐기성소화조에서 발생하는 바이오가스($CH_4$ 농도: 60~65%, $H_2S$: 1,500~2,500ppm)를 $200Nm^3/hr$의 유량으로 인입시켜 액화바이오메탄을 생산하였다. 연구결과, 탈황공정에서는 가성소다 세정법을 이용하여 1,500~2,500ppm으로 인입되는 $H_2S$를 100ppm 이하로 제거한 후, 흡착법을 이용하여 $H_2S$를 완전히 제거하였다. 바이오가스에 포화된 수분은 냉각제습과 흡착제습공정을 통해 Dew point $-70{\sim}-90^{\circ}C$까지 제거하여 안정적으로 $CO_2/CH_4$ 분리공정에 인입시켰다. $CO_2/CH_4$ 분리공정은 흡착방식을 적용하여 $CH_4$ 순도가 95% 이상인 바이오메탄을 생산하였으며, 이때 메탄 회수율은 약 87%이였다. $CO_2$가 분리된 바이오메탄은 초저온액화공정을 이용하여 액화바이오메탄으로 전환시켰다. 이때 초저온액화공정은 Reverse Brayton cycle로 구성하였으며, 냉매로는 질소를 사용하였다. 액화바이오메탄의 생산은 바이오메탄을 등엔트로피과정인 단열팽창을 통하여 $-155{\sim}-159^{\circ}C$의 초저온으로 냉각되는 질소냉매와 열교환기에서 열교환시켜 이루어졌으며 그 생산량은 $3.46m^3$/day(1bar, $-161^{\circ}C$)이었다.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.640-649
• /
• 2017

A comparative research on the traditional standard wood walls and other light-frame wood walls is necessary to expand the base of wooden buildings and improve consumer satisfaction. Therefore, in this research we looked for new possibilities through comparison of performance between standard wood wall and newly presented staggered stud wood wall. First, the strength characteristics of staggered stud wood walls were evaluated and the those of standard wood walls were compared. The ultimate load of the standard wall was larger than that of the staggered stud wood wall, because the cross section of the wood making up the standard wood wall was larger than that of the staggered stud wood wall. However, the statistical analysis between the two groups didn't showed a significance of 95% confidence level. This means that, staggered stud wood walls have shown the possibility of replacing the standard wood wall. Because the cross-section of the stud in the staggered stud wood walls is smaller than that of the standard wall, the material can be saved. Therefore, staggerd wood stud wall is judged to be more economical than the standard wall. In addition, since the area of the insulation also increases, improvement of the heat bridge is also expected.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.4
• /
• pp.1-12
• /
• 2003

In this study, a regime where independent treatment of SETs in transient simulations is valid has been identified quantitatively. It is found that as in the steady-state case, each SET can be treated independently even in the transient case when the interconnection capacitance is large enough. However, the value of the load capacitance $C_{L}$of the interconnections for the independent treatment of SETs is approximately 10 times larger than that of the steady state case. A compact SET transient model is developed for transient circuit simulation by SPICE. The developed model is based on a linearized equivalent circuit and the solution of master equation is done by the programming capabilities of the SmartSpice. Exact delineation of several simulation time scales and the physics-based compact model make it possible to accurately simulate hybrid circuits in the time scales down to several tens of pico seconds. The simulation time is also shown to depend on the complexity level of the transient model.l.

• Journal of the Korean Institute of Gas
• /
• v.5 no.3 s.15
• /
• pp.1-8
• /
• 2001

This study was carried out for the purpose of determination of maintenance period and investigation of weak point due to freeze when the gas heater of KOGAS valve station Is not operated in winter season. 3-dimensional non-linear numerical simulation was conducted in order to predict the time and location which bath water in heater reaches to ice point. FLUENT V 5.0, commercial code, is used for thermal fluid flow analysis. We thought this was problem of heat conduction solving the energy equation and modeled gas heater by using the real geometry and scale for performing the 3-dimensional simulation. It was analyzed complex heat transfer phenomena considering convection due to air on surface, conduction in insulation material, natural convection of liquid in heater and heat loss through the pipe.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1995.11a
• /
• pp.115-115
• /
• 1995

다중 효용관식 증발기는 보통의 증발기에서 응축하여 제거하는 증기를 다음 효용관의 가열원으로 재사용하는 것으로 그 자체로도 에너지 절감효과가 있는 것으로 알려져 있다[1,2,4]. 기계식증기 재압축 증발기는 보통 증발기에서 응축시켜 제거하는 발생 증기를 압축하여 고온의 증기로 만든 다음 가열원으로 재이용하는 장치로 이에 대한 효용은 문헌에 잘 나타나있다[3,4]. 여기서는 다중효용관과 증기 재압축기를 조합한 증발기 중에서 Forward feed 방식의 다중효응관에 증기 재압축기를 부착한 경우에 대하여 타당한 물질수지, 열수지, 전열 식, 상평형식을 소개하였다. 또한 압축기의 용량을 결정하기 위한 단열압축공정의 지배방정 식을 소개하였다. 원료의 조건, 효용관의 수 및 총전열온도차가 주어지면 상기의 지배방정식의 해를 구할 수 있는데. 본연구에서는 Gauss-Seidel의 연속치환법을 이용하였다. 이와 같이 지배방적식의 해를 구하면 효용관의 면적, 압축펌프의 용량, 각효용관 입출구의 조건 등이 계산된다. 다중효용관 기계식 증기 재압축 증발장치의 최적화를 위하여는 효용관의 전열면적당 가격과 압축펌프의 용량당 가격 그리고 펌프를 운전하는데 필요한 전력의 요금 등의 자료가 요구된다. 총전열온도차에 따른 운전비와 시설비의 합이 최소가 되는 점이 최적 총전열온도차가 되는데 이 점을 구할 때에는 수치적으로 안정한 이분법을 이용하였다. Borland C++를 이용하여 프로그램하였으며 윈도우즈 환경에서 수행되게 하였다. 사용자 쉽게 이용할 수 있게 하기 위하여 각종 필요한 데이터를 입력할 수 있는 Edit box가 화면에 나타나게 하였다. 또한 입력된 데이터를 저장하거나 불려올 수 있는 메뉴, 입력된 데이타를 이용하여 효용관의 면적과 압축기의 용량을 계산하거나 효용관의 수가 주어졌을 때 총전열온도차를 최적화하는 것을 선택할 수 있는 메뉴 그리고 계산 결과를 파일로 혹은 프린트로 출력할 것을 선택할 수 있는 메뉴가 있다. 사용자는 해당되는 데이타를 입력한후 마우스로 원하는 작업의 메뉴를 선택하면 된다.

• Geophysics and Geophysical Exploration
• /
• v.18 no.1
• /
• pp.21-30
• /
• 2015

Induced seismicity has been observed in the relation with lots of anthropogenic influence and at variety of geological conditions over the last several decades. This paper reviews those induced earthquakes and compares with each other as well as with natural tectonic earthquakes. Hydraulic fracturing is commonly used to enhance the permeability through new cracks in the rock formation. The process triggers the induced seismicity, which can give crucial information on the fracture network and oil/gas migration. In the similar way, unintentionally induced events during the production procedure of the field, dam reservoir, minig activity, or wastewater injection can be used to give insight into various hydrodynamic processes and changes of reservoir properties at a various scales. The general conclusion summarizes the uncertainty or limitations of knowledge up to date and presents some issues to be dealt with in the future research.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.8
• /
• pp.1774-1781
• /
• 1997

In this paper, we propose a full digital frequency and phase locked loop for CATV and HDTV receivers adopting VSB modulation. The CATV and HDTV receivers proposed by the Grand-Alliance in USA are ultilizing analog signal processing technology for carrier recovery. By the way, it is not a good architecture for the development of single chip ASIC operating in digital domain. To solve this problem while improving the performance, we first down convert the received r.f. signal to a near baseband signal for a low-rate AD converter and then we use digital signal processing techniques. The proposed system has the frequency pull-in range of -200 KHz +2.50 KHz. Moreover, it has the ability of adaptive loop bandwidth control according to the amount of frequency offset to improve the acquisition time while reducing the phase noise.

• Fire Science and Engineering
• /
• v.31 no.3
• /
• pp.79-87
• /
• 2017

Sandwich panels which are having the both sides are bonded with a heat insulating material with an iron plate are used as factories, warehouse structures as advantages of convenience in construction at economic efficiency of material cost. However, in a panel structure constructed by continuous joining of sandwich panels, a joint portion where a panel and a panel are connected is generated. The joint part is a part which is easily vulnerable to fire because flames easily flow into the melting and deformation of the iron plate during fire. The flames flowing into the panel induce diffusion of fire by rapid burning, causing damage of human life and property. In this research, we developed a flame spread prevention plate to prevent spreading of sandwich panel. This is an improvement of the workability by the anti-spreading construction method of the existing previous research, it can be applied independently to the connecting part where the panel and the panel are coupled, designed to prevent inflow and spreading of flame did. The actual fire test of the test method of KS F ISO 13784-1 of the sandwich panel specimen was conducted and the burning behavior corresponding to the presence or absence of application of the flame spread prevention plate was grasped at the panel connection part and its effect was measured. Inserting a fire spreading plate into the test result panel connecting part is measured by delaying the flashover, prevention of collapse of the specimen, and temperature rise of the opening, effectively improving the fire safety of the panel structure It was confirmed as a method that can be secured. It is judged that panel structure will contribute to ensuring fire safety by applying the fire spread prevention construction method of various methods ensuring the workability and economy of panel connection vulnerable to fire.

• Journal of Bio-Environment Control
• /
• v.8 no.2
• /
• pp.136-146
• /
• 1999

A series of experiments were carried out in winter to investigate the indoor thermal environment in greenhouses with different kinds of heating systems, and characterize the energy consumption, heat transport and thermal energy efficiency of each system. By the Quantitative calculation of heat losses which transmit through the covers of greenhouse, the fundamental data of energy-saving of the particular heating system were obtained. And from the analysis of air temperature differences between indoor and outside, it was possible to select more effective energy-saving and comfortable heating system in greenhouses. The electric heater was more stable in thermal environment and cheaper in cost, since it could be used during the surplus time of electric power from 10：00 p.M. to 8：00 A.M. But the low air temperature in greenhouses besides these times resulted in a chilling problem of the crops. The heating system by hot air had the advantage to show nearly uniform temperature difference by the height above the ground. But the system had the disadvantage to require more energy consumption than the electric heating system.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.6
• /
• pp.305-314
• /
• 2017

Ocean wave energy harvesting is still too expensive despite developing a variety of wave energy converter (WEC) devices. For the cost-effective wave energy harvesting, it can be an effective measure to use existing breakwaters or newly installed breakwaters for both wave control and energy harvesting purposes. In this study, we investigated the functionality of both breakwater and wave-power generator for the oscillating water column (OWC)-type wave energy converter (WEC) installed in a pneumatic floating breakwater, which was originally developed as a floating breakwater. In order to verify the performance of the breakwater as a WEC, the air flow velocity from air-chamber to WEC has to be evaluated properly. Therefore, air flow velocity, wave transformation and motion of floating structure was numerically implemented based on BEM from linear velocity potential theory without considering the compressibility of air within the chamber. Air pressure, meanwhile, was assumed to be fluctuated by the motions of structure and the water level change within air-chamber. The validity of the obtained values can be determined by comparing the previous results from the numerical analysis for different shapes. Based on numerical model results, wave transformation characteristics around OWC system mounted on the fixed and floating breakwaters, and motions of the structure with air flow velocities are investigated. In summary, all numerical results are almost identical to the previous research considering air compressibility. Therefore, it can be concluded that this analysis not considering air compressibility in the air chamber is more efficient and practical method.