• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.9 s.351
• /
• pp.60-68
• /
• 2006

Using the wireless communication among unacquainted vehicles, an intelligent vehicle safety system can be constructed to exchange vehicle safety-related information, such as urgency stop, traffic accident and road obstacles. In the majority of vehicle safety applications, vehicle safety messages are propagated in the form of broadcast. However, this approach causes some effectiveness and performance problems with massive radio collision, multi-hop propagation. This paper presents a priority based relay node selection method for propagating vehicle safety messages of traffic accident protection system. With this method, vehicle safety messages are relayed by a node that locates in proper distance out of the nodes that are included in the radio transmission range. By decreasing the number of duplicated messages, the packet overhead is lessened while the communication performance is raised. The proposed method was proven to be better than other schemes through network simulations.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.2
• /
• pp.313-320
• /
• 2018

The importance of sensors on a self-driving vehicle has rising since it act as eyes for the vehicle. Lidar sensors based on laser technology tend to yield better image quality with more laser channels, thus, it has higher detection accuracy for obstacles, pedistrians, terrain, and other vechicles. However, incorporating more laser channels results higher unit price more than ten times, and this is a major drawback for using high channel lidar sensors on a vehicle for actual consumer market. To come up with this drawback, we propose a method of integrating multiple low channel, low cost lidar sensors acting as one high channel sensor. The result uses four 16 channels lidar sensors with small form factor acting as one bulky 64 channels sensor, which in turn, improves vehicles cosmetic aspects and helps widespread of using the lidar technology for the market.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.7
• /
• pp.849-856
• /
• 2020

Recently, as the number of high-height vehicles such as double-decker buses has increased, collision accidents have occurred in bridges and tunnels due to the deviation from the designated routes and driver's carelessness. In the case of the existing front collision warning system, it is limited to vehicles and pedestrians, so it is difficult to use it as a pass height warning system for the high height vehicles. In this paper, we propose a system that generates a warning by determining the correlation and time series characteristics of data for each segment using multiple lidar sensors and then determining the possibility of collision in the upper part of the vehicle. Also, the proposed system confirmed the proper operation through a real-time driving test and a system performance evaluation by the Korea Automobile Testing & Research Institute.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.10C
• /
• pp.995-1006
• /
• 2003

It is well know that in the wireless communication systems the transmitted signals can suffer from multipath fading due to the wave propagation characteristics and the obstacles over the paths, resulting in serious reduction in the power of the received signals. However, it is possible to take advantage of the inherent diversity imposed in the multipath reception if the underlying channel can be properly estimated. One of the diversity reception methods in this case is Rake processing. In this paper we study the Rake receivers for the direct-sequence spread-spectrum communication systems utilizing PN (pseudo noise) sequences to achieve spread spectrum. A conventional Rake receiver can use the finite-duration impulse (FIR) filter followed by the PN sequence demodulator, where the FIR filter coefficients are the reverse-ordered complex conjugate values of the fading channel impulse response estimates. Here, we propose a new Rake processing method by replacing the aforementioned PN code sequence with a new set of optimum demodulator coefficients. More specifically, the concept of the new optimum Rake processing is first introduced and then the optimum demodulator coefficients are theoretically derived. The performance obtained using the new optimum Rake processing is also calculated. The analytical results are verified by computer simulation. As a result, it is shown that the new optimum Rake processing method improves the MSE performance more than 10 dB over the conventional one using the fixed PN sequence demodulator. It is also shown that the new optimum Rake processing method improves the MSE performance about 10 dB over the Adaptive Correlator that performs the combining of the multipath components and PN demodulation concurrently. And finally, the MSE performance of the optimum Rake demodulator is very close to the MSE performance of OPSK demodulator under the AWGN channel.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37C no.9
• /
• pp.774-783
• /
• 2012

A simple, accurate, secure, long-lasting, and portable hybrid positioning system is proposed and designed in this paper. It consists of a lighting LED that generates visible light data corresponding to position information of a target and a Zigbee wireless network communication module with low power, security, and service area expansion characteristics. Under an indoor environment where there is 23.62m distance between an observer and the target, the presented hybrid positioning system is tested and is verified with the functions of Zigbee three hop wireless networking and visible light communication (VLC) scheme. The test results are analyzed and discussed.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.1
• /
• pp.7-13
• /
• 2008

This paper suggests a Path-planning algorithm for mobile agents. While there are a lot of studies on the path-planning for mobile agents, mathematical modeling of complex environment which constrained by spatio-temporally is very difficult and it is impossible to obtain the optimal solutions. In this paper, an optimal path-planning algorithm based on the graphic technique is presented. The working environment is divided into two areas, the one is free movable area and the other is not permissible area in which there exist obstacles and spatio-temporally constrained, and an optimal solution is obtained by using a new algorithm which is based on the well known ACO algorithm.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.4
• /
• pp.253-265
• /
• 2016

We propose an obstacle classification method using multi-decision factors and decision sections based on Single 2D LiDAR. The existing obstacle classification method based on single 2D LiDAR has two specific advantages: accuracy and decreased calculation time. However, it was difficult to classify obstacle type, and therefore accurate path planning was not possible. To overcome this problem, a method of classifying obstacle type based on width data was proposed. However, width data was not sufficient to enable accurate obstacle classification. The proposed algorithm of this paper involves the comparison between decision factor and decision section to classify obstacle type. Decision factor and decision section was determined using width, standard deviation of distance, average normalized intensity, and standard deviation of normalized intensity data. Experiments using a real autonomous vehicle in a real environment showed that calculation time decreased in comparison with 2D LiDAR-based method, thus demonstrating the possibility of obstacle type classification using single 2D LiDAR.

• Journal of the Korean Society of Safety
• /
• v.27 no.6
• /
• pp.70-77
• /
• 2012

Experimental investigations were performed to examine the characteristics of propagating flame fronts around multiple bars within a rectangular chamber. The explosion chamber is 400 mm in height, $700{\times}700mm^2$ in cross-section and has a large top-venting area, $A_v$, of $700{\times}210mm^2$. This results in a value of 0.44 for $A_v/V^{2/3}$ and a L/D value of 0.57. The multiple obstacles of length 700 mm with a blockage ratio of 30 % were placed within the chamber. Temporally resolved flame front images were recorded by a high speed video camera to investigate the interaction between the propagating flame and the obstacles. Results showed that the flame propagation speeds before the flame impinges onto the obstacle almost equal to the laminar burning velocity. As the propagating flame impinged on the obstacle, the central region of flame began to become concave, this resulted in the flame deceleration in the region. As the flame interacted with the modified flow filed generated behind the central obstacle, the probability density functions(PDFs) of the local flame displacement speed were extensively distributed toward higher speeds.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.422-424
• /
• 2014

IPS 측위는 실내의 특정 위치의 무선 신호 정보를 수집하여 radio map을 구성하고 측위 시점에 구성된 정보와 수집된 무선 정보를 비교하여 현재 위치를 판단한다. 비교방법은 핑거프린트, 삼각 측량법 등의 알고리즘을 활용하며 최근에는 wifi 신호와 다른 신호를 혼합하여 계산하거나 다중 비교 방식을 사용하여 정확도를 높이는 측위 방법도 개발되었다. 앞서 언급한 측위방법은 비교적 정확한 실내 위치를 판단하지만 구축된 radio map정보와 측위 시점에서 수집된 신호 정보가 상이할 경우 측위 정확도는 크게 하락한다. 구축 시점과 측위 시점의 무선 신호에 차이가 발생하는 이유는 신호 발생 기기의 고장, 장애물 발생, 채널 간섭 현상 등이다. 특히 채널 간섭은 구축된 신호 영역 내에 동일 채널 및 인접 채널을 가지는 AP 및 테더링 기기 등이 신규로 설치되었을 때 측위에 영향을 주는 신호잡음 현상이다. 본 논문에서는 앞서 언급한 문제점을 해결하기 위해 신호 잡음에 강인한 IPS용 라디오맵에 대하여 제안한다. 제안하는 radio map 설계 방법은 측위 시점에 신호잡음이 발생하였을 때 이 정보를 수집하여 기존 radio map에 반영하여 정확도를 유지하는 방법이다. 이 방법을 적용할 경우 신호잡음에 능동적으로 대처하여 IPS 측위의 정확도를 높일 수 있을 것으로 사료된다.

• Journal of Korean Society for Geospatial Information Science
• /
• v.24 no.3
• /
• pp.11-18
• /
• 2016

Since GNSS signals get blocked by buildings in urban canyons or narrow alleys, it is very difficult to secure a enough number of visible satellites for satellite navigation in those poor signal-reception environments. In those situations, one cannot get their coordinates or obtain accurate positions. In this study, a couple of strategies for improving positioning accuracy in urban canyons were developed and their performance was verified. First of all, we combined GPS and GLONASS measurements together and devised algorithms to quality-control observed signals and eliminate outliers. Also, a new multipath reduction scheme was applied to minimize its effect by utilizing SNR values of the observed signals. For performance verification of the developed technique, a narrow alley of 10m width located near the back gate of the Inha University was selected as the test-bed, and then we conducted static and kinematic positioning at four pre-surveyed points. We found that our new algorithms produced an 45% improvement in an open-sky environment compared with the positioning result of a low-cost u-blox receiver. In the alleys, 3-D accuracy improved by an average of 37%. In the case of kinematic positioning, especially, biases showing up in regular receivers got eliminated significantly through our new filtering algorithms.