• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.922-928
• /
• 1998

This paper presents the automatic alignment measuring system for improving the accuracy and working time of alignment of large vertical hydraulic pump turbine. It is general practice that rotating shaft should run within acceptable vibration limit. In order to obtain better run-out data of multi-stage rotor, careful and accurate alignment approach must be established. Generally, present alignment procedure are required several iterative works and so many manpower. Therefore, the new system has been developed using a vector calculation algorithm, laser sensor and data acquisition devices. As a result of appling to actual machines, it is confirmed that manpower is saved up to an average 90%.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.111-111
• /
• 2004

회전축계는 발전기의 터빈이나 가스터빈 그리고 항공기의 회전익, 선박, 자동차등 산업전반에 널리 사용되어지고 있다. 이러한 회전축계의 안정성 확보와 성능향상을 위해서는 정확한 동적 모델링이 필요하며 지금까지 많은 연구가 되어 왔다. 일반적으로 회전축계의 동특성 이론 모델은 회전관성, 자이로모멘트, 전단변형을 포함하는 티모센코 축 요소를 널리 사용하고 있으며, 많은 연구를 통해 그 유용성이 입증되어 왔다.(중략)

• Journal of Power System Engineering
• /
• v.14 no.1
• /
• pp.47-52
• /
• 2010

In this study, Finite Element Analysis have been adopted to analyze reducing stress effect and used to induce the sensitivity of design parameter on various techniques which was used for reducing stress. And so it can be utilized as a data to design on similar model. The effect of reducing stress with respect to change of relief groove radius can be increased by 27.3~18.2 % more than radius of fillet. And if a shoulder fillet radius is larger, additional reducing stress by relief groove radius is not obtained. And there was only little effect on reducing stress by changing the center point of groove radius along horizontal direction. In the case that undercut radius is 1.5mm, Max. Equivalent stress is reduced by 5.71% under bending force and 11.11% under torsion. The best effect of reducing stress at undercut model was yielded when the undercut radius is a forth of difference of stepped shaft radius.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1479-1485
• /
• 2010

In recent times, due to wire drawing of high carbon steel at a high speed to ensure a high productivity and high strength, axial residual stress are generated because of rapid increase in surface temperature. In the process, the temperatures of the wires increased because of the deformation of the wires and the friction between the die and wire. In particular, in the case of the wire drawing at a high speed, friction leads to a large temperature gradient so that considerable axial residual stress is generated on the surface. In this study, the relationship between axial residual stress and increase in the surface temperature was investigated, and a prediction model of uniform temperature was proposed. Then, a prediction model for residual stress was developed. The proposed model was verified by measuring the residual stress by X-ray diffraction on drawn wires.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.9
• /
• pp.875-882
• /
• 2011

In the present study, the imbalance in the axial-thrust and variation in the volumetric efficiency that occurred during the trimming of impeller diameter were investigated. The present study was focused on low-specific-speed multistage centrifugal pumps with a balancing piston as the balancing mechanism. The effects of impeller trimming on the axial-thrust balance in multistage pumps with horizontal and vertical axes were compared. The results showed that impeller trimming resulted in an additional axial-thrust acting in direction of pump inlet. The axial-thrust imbalance due to impeller trimming was more severe in the vertical-axis pumps than in the horizontal-axis pumps. The rate of increase in the diameter of the balancing piston, which was proportional to the rate of impeller trimming, was evaluated to maintain the axial-thrust balance. Furthermore, a simultaneous increase in the piston length and piston diameter was more effective for reducing the axial-thrust imbalance along with the volumetric efficiency drop.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.797-798
• /
• 2008

• Proceedings of the Korean Information Science Society Conference
• /
• 2002.10e
• /
• pp.640-642
• /
• 2002

본 논문에서는 실제 네트워크에서 측정되고 있는 시간축상으로 매우 불안정한 상태의 트래픽 즉, ON／OFF 소스 모델로 가정하여 발생시킨 self-similar 트래픽을 이용하여 다단으로 이루어진 스위치 모델의 처리시간(processing time)에 따른 출력단에서self-similarity의 변화와 이용도(utilization) 등을 사용하여 네트워크의 성능을 분석한다.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.2
• /
• pp.107-113
• /
• 2006

This paper presents an efficient dynamic modeling method for multi-stepped rotor system using effective spring elements to take into account the structural weakening effect due to the steps. This paper demonstrates that the Timoshenko shaft model give rise to a significant error in the case of multi-stepped rotors. An effective bending spring model is introduced to represent the structural weakening effect in the presence of steps. The proposed modeling method is validated through a series of simulations and experiments. Finally, a spindle is dealt with as an analysis example.

• Journal of the Korean Institute of Gas
• /
• v.24 no.1
• /
• pp.49-55
• /
• 2020

Experimental investigations were conducted to understand the multi-staged combustion characteristics of a swirl-stabilized double cone premixed burner nozzle used for industrial gas turbines for power generation. Multi-staged combustion is implemented by injecting the fuel through the existing manifold of the side slots as well as through the apex of the cone with two fuel injection angles which are slanted or axial. NOx and CO emissions, and wall temperature distributions were measured for various fuel distributions and operating conditions. Results show that NOx emissions are decreased when the fuel distribution to the apex is 3% of the total amount of fuel, which is due to more uniform fuel distribution inside the nozzle, hence less hot spots at the flame. NOx emissions are rather increased when the fuel distribution to the apex is 8% of the total amount of fuel for axial fuel injection by occurrence of flash back in premixing zone of burner.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.506-508
• /
• 2013