• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.137-137
• /
• 2013

본 연구에서는 반도체 검사 장비인 프로브 카드의 핵심 부품인 프로브 니들의 팁 부분의 내마모성을 향상시키기 위하여 무전해 Ni-B-W 합금 도금 실험을 실시하였다. 무전해 Ni-B-W 합금 도금 실험에서 여러 가지 제어인자 중 도금욕의 pH와 온도 그리고 환원제의 농도 등을 변수로 하였다. 도금욕 pH와 온도에 따른 전착속도 및 물성 변화를 관찰하였으며, 환원제 농도 변화에 의한 open circuit potential의 변화를 측정하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.162-173
• /
• 1998

The high pressure common rail injection system offers a high potential for improving emmisions and performance characteristics in large direct diesel engines. High pressures in the common rail with electronic control allows the fuel quantity and injection timing to be optimized and controlled throughout a wide range of engine rpm and load conditions. In this study, high pressure supply pump, common rail, pipes, solenoid and control chamber, and nozzle were modeled in order to predict needle lift, rate of injection, and total injected fuel quantity. When the common rail pressure is raised up to 13.0 ㎫ and the targer injection duration is 1.0ms, the pressure drop in common rail is about 5.0㎫. The angle of effective pressurization is necessary to be optimized for the minimum pump drive torque and high pressure in common rail depending on the operating conditions. The characteristics of injection were also greatly influenced by the pressures in common rail, the areas of the inlet and exit orifice of the control chamber.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.14-17
• /
• 2011

Numerical simulation was carried out for the SNECMA modulatable thrust devices, with four different nozzle contraction angle $45^{\circ}$, $60^{\circ}$, $83^{\circ}$, and $90^{\circ}$, respectively. Results show that $83^{\circ}$ nozzle contraction is better in that it comes up with good thrust level with small aerodynamic load.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.165-166
• /
• 2006

• Design & Manufacturing
• /
• v.10 no.3
• /
• pp.25-29
• /
• 2016

Recently, a hyaluronic acid micro needle patch for therapeutic and cosmetic purposes has been used by attaching directly to the skin with a pattern having a micro needle shape of 1/3 thickness of hair. These products are attracting attention as an innovative product that maximizes the effect by activating the active ingredient in the skin in the deep skin without blocking the horny layer because the micro needle shape exists on the patch surface so that it can penetrate effectively to the skin. Currently, DAB (droplet air blowing) or MEMS technology is used to make pattern shapes for patches. Because of this technology, manufacturing time is long and manufacturing cost is high, so we tried to develop the mold technology to machine the microneedle shape directly to the metal. In this study, we first fabricated a needle pattern with a quadrangular pyramid shape and finally produced a conical needle pattern.

• Journal of computational fluids engineering
• /
• v.19 no.2
• /
• pp.30-39
• /
• 2014

We report in this paper the analysis of the motion of a needle and a spring in a viscous fluid under the influence of gravitational force. Lateral shift as well as vertical motion of a needle falling in a viscous fluid has been observed from a simple experiment. We also observed the combined rotation and translation of a falling spring. The trajectory and velocity of the falling needle and the spring were obtained by using an image processing technique. We also conducted numerical simulation for both problems. For the falling-needle problem, we employed a theory; but it turns out that significant correction is required for the solutions to match the numerical and experimental data. For the falling spring problem various theoretical formula were tested for their justification, but none of the existing theories can successfully predict the numerical and experimental results.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.8
• /
• pp.1077-1085
• /
• 1997

The use of "clean fuels" such as butane, propane, and mixtures of these (LPG) is an attractive way to reduce exhaust emissions. In this study internal flow of the pintle type injector for LPG engine is studied. The breakup of liquid jet is the result of competing, unstable hydrodynamic forces acting on the liquid jet as it exits the nozzle. The nozzle geometry and up-stream injection conditions affect the characteristics of flow inside the nozzle, such as turbulence and cavitation bubbles. A set of calculations of the internal flow in a pintle type nozzle were performed using a two dimensional flow simulation under different nozzle geometry and upstream flow conditions. The calculation showed that the turbulent intensity and discharge coefficient are related to needle leading angle(.alpha.) and needle lift.edle lift.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.231-232
• /
• 2006

Ultrasonic machining technology has been developed over recent years for manufacturing the quality-assured precision parts fur several industrial application such as optics, semiconductors, aerospace and automobile application. Ultrasonic needle horning is widely used in cutting(drilling) of non-conductive, brittle workpiece materials. This paper intends to understanding of the basic mechanism of ultrasonic needle horning. And frequency analysis program is used to easily predict the natural frequency of ultrasonic vibration cutting tools.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.35-40
• /
• 1987

The experimental study, using constant pressure injection system, is carried out to investigate the effect of the geometrical shape changes of the needle valve of the effective flow area, the spray angle and the Sauter's Mean Diameter according to needle valve lift for a pintle-type injection nozzle. The results are as follows: 1) With the increase of the needle valve lift, the effective flow area is increased, the spray angle is at first increased and later decreased, and the Sauter's Mean Diameter is decreased. 2) It is also shown that the spray angle is maximum at the rapidly increased region of the effective flow area.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.140-140
• /
• 2012

로듐은 열전도성 및 전기전도도가 우수할 뿐 아니라 산/알칼리에 잘 부식되지 않으며 강한 내구성을 지니고 있어서 장식 및 액세서리의 표면처리 및 각종 전기/전자산업의 부품으로 널리 이용되어지고 있다. 본 연구에서는 반도체 검사 장비인 프로브 카드에 조립되어 있는 프로브 니들의 내마모성을 향상시키기 위하여 로듐도금의 특성을 연구하였다. 로듐의 이온 공급원으로 Rhodium sulfate 를 사용하였다. 시편은 황동 시편($0.5cm{\times}2cm$)을 사용하였다. 로듐 도금 시 여러 가지 제어인자 중도금욕의 온도(상온, $40^{\circ}C$, $60^{\circ}C$)와 황산농도(10ml/l, 50ml/l, 100ml/l) 그리고 전류밀도(0.2ASD, 0.5ASD, 1.0ASD)를 변수로 하여 실험을 하였다. 각각의 변수에 따라 전류 효율 및 전착 속도를 분석하였으며, 현미경을 이용하여 표면을 관찰하였다. 그리고 비커스 경도계를 이용하여 경도를 측정하였다.