• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.9
• /
• pp.563-570
• /
• 2017

Experimental and numerical studies were performed to investigate the performance and internal flow characteristics of a supersonic second throat exhaust diffuser (STED) with back pressure ($P_a$). An ejector system was used to vary the back pressure ($P_a$) conditions. The operating gas for the STED and the ejector was high pressure nitrogen at room temperature. When the back pressure ($P_a$) at a constant nozzle inlet pressure $P_0$) decreases, the pressure recovery location moves downstream. If the pressure ratio $P_0/P_a$) is the same, even if the nozzle inlet pressures $P_0$) are different, the diffuser's internal flow pattern and starting pressure ratio ($(P_0/P_a)_{st}$) are almost the same.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.6
• /
• pp.25-30
• /
• 2010

Dual throat nozzle(DTN) is recently attracting much attention as a new concept of the thrust vectoring technique. This DTN is designed with two throats, an upstream minimum and a downstream minimum at the nozzle exit, with a cavity in between the upstream throat and exit. In the present study, a computational work has been carried out to analyze the performance of a dual throat nozzle(DTN) at various mass flow rate of secondary flow and nozzle pressure ratios(NPR). Two-dimensional, steady, compressible Navier-Stokes equations were solved using a fully implicit finite volume scheme. The present computational results were validated with some experimental data available. Based upon the present results, The control effectiveness of thrust-vector is discussed in terms of the thrust coefficient and the discharge coefficient.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.10
• /
• pp.817-824
• /
• 2015

Experiments were carried out to investigate the flow and mass transfer characteristics of an orifice nozzle. Measurements of primary and suction flow rates, dissolved oxygen concentration, and electric power were obtained. Vertically injected mixed-jet images were captured by a direct visualization technique with a high speed camera unit. The mass ratio, volumetric mass transfer coefficient, and mass transfer performance were calculated using the measured data. As the primary flow pressure increases, the mass ratio decreases slightly, while the volumetric mass transfer coefficient and electric power increase. As the primary flow pressure increases and the mass ratio decreases, the mass transfer rate increases because of the fine bubbles and wider distribution of the bubbles.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.5
• /
• pp.476-482
• /
• 2009

The effect of pintle shape on the thrust level of pintle-nozzle Solid Rocket Motor(PNSRM) was studied numerically using the Spalart-Allmaras turbulent model of Fluent. Mass flow rate of PNSRM was always less than theoretical value and the extent of decrease in mass flow rate grew in the large pintle because of increase in the relative boundary layer thickness between pintle body and nozzle wall. The bigger pintle size was, the more thrust of pintle tip pressure was obtained. Meanwhile the more thrust of nozzle and chamber pressure decreased. Hence, total thrust of big pintle was less than a small pintle under same throat area condition. Specific impulse was relatively flat for all pintle shape.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.4
• /
• pp.52-62
• /
• 2017

The study for the performance characteristics of the nozzleless booster used in ramjet booster was carried out. Performances related to pressure and thrust for nozzleless booster are lower than classical motor those because of absence of convergent and divergent sections of nozzle. To solve this problem, it developed a high-performance propellant with maximum impulse density included Al as metal fuel. Using the nozzleless booster casted the propellant, ground test of it was carried out by varying the length-to-diameter ratio (L/D ratio) of the propellant. Specific impulse of nozzleless booster was limited to about 75 percents of its value compared with that of classical motor adapted nozzle in the same propellant and propellant length and will be estimated approximately 85 percents of its value compared with that of classical motor at same average pressure in terms of the curve fitting by our test results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.5
• /
• pp.24-31
• /
• 2002

The effects of vortex generators, in the form of small delta-shaped tabs or thin tapes at an axi-symmetric supersonic nozzle exit, on the characteristics of supersonic jet flowfields are investigated by Schlieren images and Pitot-tube measurements. Small tabs as small as 1 % of the nozzle exit area can introduce streamwise vortices and produce a significant effect on the jet flowfield downstream of the nozzle. The effect is stronger for the cases of under-expanded jet than over- and perfect-expanded cases, introducing a larger flow entrainment. The effects of the angle of tabs with respect to the flow direction are also investigated, and for over-expanded jet cases, it is found that the tabs bended toward upstream can weaken the interaction strength and remove the Mach disc in the jet flowfield. Introduction of small proturbances inside the nozzle surface by attachment of thin tapes is also found to change the pressure distribution in the circumferential direction of the flowfield. Its effect is also found to be dependent on the jet expansion ratio.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.1
• /
• pp.44-53
• /
• 2004

This paper is to investigate the combustion characteristics with a three dimensional chemical reacting flow on the aspect ratio of an exit configuration of the slit type nozzle for the fuel injection and to device the methods of combustion／mixing enhancement. The results show that both inside inflow and slit side vertices should be considered from a viewpoint of the mixing. The combustion efficiency becomes the smallest at aspect ratio, where the aspect ratio is less and more than unity, respectively. The total pressure loss becomes the largest at aspect ratio of unity due to the high penetration. All results imply that a streamwise very long slit is desirable with respect to the combustion and the pressure loss.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.5
• /
• pp.101-106
• /
• 2019

Carbon deposition on the turbine nozzle throat of a LOx/kerosene gas generator cycle(open cycle) engine causes performance reduction of the engine. Estimation methods for a turbine nozzle throat area are proposed. The discharge coefficient of the turbine nozzle was estimated with the turbine gas properties such as gas constant, specific heat ratio, and temperatures. The pressure ratio and temperature ratio of the turbine nozzle throat, was utilized to estimate the discharge coefficient also. Estimated discharge coefficient of turbine nozzle throat of KSLV-II 1st stage engine shows the carbon deposition effects on the turbine nozzle throat of a LOx/kerosene open cycle engine.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.211-214
• /
• 2011

In the present work, a computational study was conducted to investigate characteristic of lateral force on the flow fields inside the propulsion nozzle with step. The unsteady, compressible, axisymmetric, Navier-Stocks equations with SST k-${\omega}$ turbulence model are solved using a fully implicit finite volume scheme. In order to simulate the shut-down process of the engine, NPR is varied from 100.0 to 10.0. It is observed that the separation point and Mach-disk strongly depend on the variation of NPR, and adjusting the step lead to significantly different characteristics in the lateral forces.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.5
• /
• pp.22-31
• /
• 2018

In this study, numerical simulations were performed to determine the dynamic characteristics of a pintle nozzle, with changes to the chamber boundary conditions. To apply movement, to the pintle, the nozzle and pintle were created separately by an auto-grid generation program using an overset grid method. The chamber boundary conditions were selected between a constant mass-flow rate condition and a propellant burn-back condition. The pressure and thrust characteristics of the constant mass-flow rate condition were determined by changing the ratio of the mass-flow rate in the inlet. The propellant burn-back condition was considered by formulation of the combustion rate. The burn-back conditions represented nonlinear phenomena, unlike the constant mass flow rate, and a small flow rate resulted in a large change in the chamber pressure.