• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.3
• /
• pp.77-84
• /
• 2021

In this study, flexural tests of prestressed high strength spun concrete (PHC) piles reinforced with infilled concrete and longitudinal rebars were conducted, where the longitudinal rebar ratio and the presence of sludge formed on the inner surface of PHC pile were set as key test variables. A total of six PHC pile specimens were manufactured, and their flexural behaviors including failure mode, crack pattern, longitudinal strain distribution in a section and end slip between external PHC pile and infilled concrete were measured and discussed in detail. The test results revealed that the flexural stiffness and strength increased as the longitudinal rebar ratio became larger, and that the sludge formed on the inner surface of PHC pile did not show any detrimental effect on the flexural performance. In addition to the experimental approach, this study presents a nonlinear flexural analysis model considering compatibility conditions and strain and stress distributions of the PHC piles and infilled concrete. The rationality of the nonlinear flexural analysis model was verified by comparing it with test results, and it appeared that the proposed model well evaluated the flexural behavior of PHC piles reinforced with infilled concrete and longitudinal rebars with a good accuracy.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.1
• /
• pp.63-72
• /
• 2006

Coulomb's theory has traditionally been used for the estimation of active earth pressure acting on rigid walls. However, many experimental data show that active earth pressures on rough, rigid walls are nonlinearly distributed. This is due to the arching effects produced by friction between the wall and backfill materials when the wall translates away from the backfill. Although there are analyses that take arching into consideration f3r a horizontal backfill surface and a vertical rigid wall, these analyses were derived for homogeneous backfill. Therefore, it is not possible to use these analyses for a caisson backfilled with crushed rock and sand, a common type of rigid wall for harbor structures. In this study, a new formulation for calculation of the nonlinear active earth pressure acting on a caisson backfilled with crushed rock and sand is proposed considering both internal friction angles and unit weights of the crushed rock and sand.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.750-757
• /
• 2018

The mechanically stabilized earth wall abutment is an earth structure using a mechanically stabilized earth wall and it uses in-extensional steel reinforcements having excellent friction performance. In order to analyze the pullout behavior of in-extensional steel reinforcements usually applied on the mechanically stabilized earth wall abutment, effects of stiffness and particle-size distributions of backfills and also horizontal spacings were considered in this study. As a result of parametric analyses, the highest pulling force acted on the uppermost reinforcement, and the stiffness and the particle-size distributions of the backfill significantly affected the pulling resistance of the reinforced soils. The internal friction angle of backfills should be at least 25 degrees, the coefficient uniformity factor should be at least 4, and the horizontal spacing of the uppermost steel reinforcement should be less than 25cm. Therefore, in order to secure the pullout resistance of the reinforced soil, it is necessary a properly spacing of reinforcement and more strict quality control for the backfill.

• Geotechnical Engineering
• /
• v.6 no.4
• /
• pp.7-18
• /
• 1990

To deal with the case of a rigid retaining wall built close to a stable rock face with cohesionless backfill, analytical solution methods Proposed by Spangler- Handy and Sokolovskii are modified. The modified solution methods, taking into account different friction angles along the wall and the rock face, can estimate the developed static or dynamic horizontal earth pressures behind vertical retaining walls experiencing various types of outward wall movements. The range of application of each proposed method, which is represented by the ratio of the distance between the wall and the rock face to the height of the wall, is compared with each other and also is examined for different wall friction angles as well as soil friction angles. Further, the result predicted by the modified Spangler - Handy solution method is compared with that from the experimental model test on sand. The comparison shows in general good agreements at various stages of retaining wall rotation about its toe. Finally results of analytical parametric study, together with the design charts, are presented to demonstrate the effects of wall friction angles and horizontal acceleration coefficients.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.5
• /
• pp.171-191
• /
• 1999

The final aim of this research is to systematize the reinforced-earth wall system using the geosynthetic composite reinforcement in the weathered granite backfill soils having relatively large amount of fines. As a staged endeavour to accomplish this purpose, laboratory pull-out tests and finite element modeling are carried out in the present study focusing on the analyses of friction characteristics associated with interaction behaviors of the geosynthetic composite reinforcement composed of geogrid with a superior function in tensile resistance and geotextile with sufficient drainage effects. In addition, drainage effects of the geotextile below geogrid are examined based on the analysis of finite difference numerical modeling. From the present investigation, it is concluded that the geosynthetic composite reinforcement in the weathered granite backfills may possibly be used to achieve effects on both a reduction of deformations and an increase of the tensile resistance, together with drainage effects resulting from the geotextile.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.15-20
• /
• 2019

This paper evaluated the construction costs of 11 design cases to decrease the horizontal forces applied to the abutment. They include two abutment types, which are to improve backfill materials for a reversed T-shaped abutment and geosynthetic Reinforced Abutment for Railways (RAR). The first type of economic analysis was that the internal friction angles of backfill materials were increased from Φ=35° to Φ=40° and 50° for a reversed T-shaped abutment. In addition, the second type was the cases with the design of geosynthetic RAR. When friction angles of 40° or 50° were applied through the improvement of the backfill material, the decrease in construction cost of the abutment was not large (2.0~3.9%), even though the horizontal forces applied to the abutment had decreased to 18~48%. In the case of applying the RAR, however, a maximum 30% cost reduction was evaluated by the decrease in horizontal force to "0" theoretically. The cost reduction resulted from the decrease in wall thickness, base slab size, and number and material change of pile foundation for the abutment.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.4
• /
• pp.143-151
• /
• 2014

This paper describes external and internal stability of reinforced earth wall using large-scale modular block and geogrid reinforcement. The evaluation for external and internal stability was conducted to analyze effect of wall height, reinforced soil (or backfill soils) and reinforcement strength. The external stability showed that the analysis cases were satisfied with design criteria, when the required minimum length and vertical spacing of reinforcement were 0.7H and 1m, respectively. The internal stability conformed that some cases were satisfied with design criteria in $25^{\circ}$ of internal friction angle of reinforced soil. Expecially, it will be applicable as wall structure considering a structural stability and economic efficiency based on evaluation of internal stability.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.9
• /
• pp.25-36
• /
• 2011

The behavior of the dry-stone masonry retaining structure has been investigated via physical model test and numerical simulation. In the model test, the digital image analysis using PIV technique was employed to measure horizontal displacements in the backfill soils and retaining blocks. For finite element numerical analyses, the commercial code, ABAQUS, was used. The horizontal displacements observed in the model test showed that the development of the failure surface is progressive. Numerical results showed that in most cases horizontal earth pressure is distributed similarly to a conventional Rankine’s distribution. However, lower values of the internal friction angle of the backfill soils and interface friction angle in the front blocks produce irregularly nonlinear distribution of the horizontal earth pressure.

• Geotechnical Engineering
• /
• v.6 no.2
• /
• pp.35-46
• /
• 1990

An analytical solution method is described to estimate the developed static and dynamic horizontal earth pressures behind a vertical or inclined rigid wall experiencing outward toranslational movement. The results predicted by the developed method of analysis are compared with chose from the experimental model testg on sandy. The comparisons show good agreements at various stases of wall movement. When the wall i9 inclined with a certain angle in the direction of the supported strand sass, the effects of reduction in developed static and dynamic horizontal earth pressures are also analyzed. Finally, results of analytical parametric study are presented to demonstrate the effects of various parameters, such as wall friction angle and internal strand friction angle.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.2
• /
• pp.94-101
• /
• 2017

Recently, the small quantity batch production method has come into the spotlight as there are more plastic processing methods. At the same time, the 3D printer market has become globally widespread due to expired 3D printer patents. In particular, the FDM method is widely used for cheap products and materials. However, the FDM scheme is not as good as the injection molding method for quality and strength. This study investigated the effect of the internal filling and strength according to layer thickness to search for the optimum printing of the factors (infill and layer thickness) that determine the strength of the model.