• Food Engineering Progress
• /
• v.23 no.2
• /
• pp.87-93
• /
• 2019

Temperature distribution studies were performed in steam-air retort to investigate the influence of various processing conditions (come-up time, sterilization temperature, and internal pressure throughout the steam-air retort). Retort temperature data were analyzed for temperature deviations during holding phase, maximum temperature difference between test locations at the beginning and after 1, 3, and 5 min of the holding phase, and box-and-whiskers plots for each location during the holding phase. The results showed that high sterilization temperature led to a more uniform temperature distribution than low sterilization temperature (pasteurization). In pasteurization condition, the temperature stability was slightly increased by increasing pressure during the holding phase. On the other hand, the temperature stability was slightly decreased in high sterilization temperature condition. Programming of the come-up phase did not affect the temperature uniformity. In addition, the slowest cold spot was found at the bottom floor during the holding phase in all conditions. This study determined that the temperature distribution is affected by retort processing conditions, but the steam-air retort needs more validation tests for temperature stability.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.10
• /
• pp.3626-3632
• /
• 2010

Some design changes were made to enhance the uniformity of temperature distribution inside the chamber of semiconductor test equipment. The design changes include the installation of adjustable airflow controller inside the chamber, the alignment of the centers of heater and match plate, the change in the size and the shape of holes in match plate base, and the addition of new holes of 2 mm diameter in order to allow airflow directly to the temperature sensors. In order to verify their effects, the temperature distributions inside the chambers were measured using 32 RTD sensors before and after the design changes. The temperature distributions were in the ranges of 87.1 to $91.5^{\circ}C$ ($90{\pm}2.9^{\circ}C$) and 89.5 to $90.8^{\circ}C$ ($90{\pm}0.8^{\circ}C$) before and after the design changes, respectively. The above temperature distribution after design changes was maintained for longer than 15 minutes, which satisfied the target temperature range of $90{\pm}1^{\circ}C$ for longer than 10 minutes.

• Journal of Biomedical Engineering Research
• /
• v.23 no.6
• /
• pp.467-475
• /
• 2002

Hyperthermia using transrectal thermal probes has been used for a noninvasive treatment of prostate diseases. However it is known that heating the rectal wall at excessively high temperature can lead to destruction of the rectal mucous membrane. and it is difficult to maintain an optimum temperature over the entire prostate. Thus, a more accurate understanding of the heat transfer mechanism between prostate and hyperthermia system is needed Numerical analysis was performed to investigate how the cold/warm stimulations on the prostate surface affect the temperature distribution in the prostate model. The general purpose software "FLUENT" was used for obtaining a finite volume solution to the unsteady conduction equation and to calculate the time-varying temperature in the prostate. Effects of the warm/cold stimulations and the stimulation frequency on the temperature distribution were simulated. and we visualized how hyperthermia affected the inside of the prostate. It was found that the effect of hyperthermia by using a typical heating method is limited due to the low thermal conductivity of the prostate. Consecutive repetitions of warm and cold stimulations were considered to provide the thermal irritations inside a prostate. The effects of temperature difference and duration of warm/cold stimulations were investigated, and basic data for the optimum period and effective patterns of stimulations were obtained. A simplified bioheat equation was also solved to describe effects of the blood flow on the blood-tissue heat transfer. The effect of blood flow was not dominant compared to that of warm/cold stimulations. These results might be used as data for design of prostate treating probe, prostatic therapy and thermal stimulation effects on the prostate.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• autumn
• /
• pp.626-629
• /
• 2003

This study is to forecast possible occurrence of internal condensation around parpets and H-beam located at the inside of balcony ceilings on the uppermost floor of super-high apartment buildings faced with open air in order to provide dwellers with more comfortable environment in the related space and get rid of their uneasiness about the condensation. In this study, we estimated internal condensation. which vary in accordance with humidity pressure distribution, at curtain walls, stone panels or lower parts of slabs that constitute outer space of the residence and are weak against heat, through temperature forecast and temperature distribution interpretation program at normal two-dimension temperature.

• Korean Journal of Optics and Photonics
• /
• v.3 no.4
• /
• pp.266-272
• /
• 1992

A coherent anti-Stokes Raman spectroscopy (CARS) technique is applied to measure temperature profile in a flame. The CARS signal is obtained with BOXCARS phase matching to get better spatial resolution. A program routine for calculating temperature of the flame from the measured CARS spectra is studied. The routine includes the line broadening mechnism of the molecules described with a modified energy gap (MEG) law by using the perturbation theory. We have found that the temperature profile obtained with the MEG law is properly fit with the results measured with a thermocoulpe and calculated with the adiabatic theory.

• Korean Journal of Food Science and Technology
• /
• v.20 no.3
• /
• pp.303-309
• /
• 1988

The heat generation at the start-up period of an autogeneous single screw extruder was determined with various feed materials, die structure and operational conditions. The highest heat generation rate was observed with defatted soybean meal, while the lowest value was obtained with rice flour, and wheat and barley flour showed the intermediate rate. As the moisture content of the flour decreased and the screw speed increased, the electric power requirement and heat generation rate increased. The temperature at compression section increased with the decrease in the particle size. The same effect was also observed as breaker plate was installed. The optimum operation was established as the temperature profile was maintained in decreasing order of metering section, die and compression section.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2004.05a
• /
• pp.147-153
• /
• 2004

본 연구에서는 MOCVD 반응기의 온도분포가 필름 성장률에 미치는 영향에 대해 분석하였다. 온도해석에는 반응기 벽면의 전도열전달과 기체의 대류열전달이 포함되었다. 또 서셉터와 실험에 사용된 그래파이트 평판 사이의 웨이퍼 미세 간극을 해석에 포함하여 반응기 내부의 온도를 예측하였다. 정밀한 온도해석을 통해 얻은 반응기의 온도 분포를 이용하여 GaAs와 InP의 필름성장률을 해석하였으며 그 결과 미세 틈새가 GaAs의 필름 성장률에 영향을 미치는 것을 확인하였다.

• Journal of Korea Multimedia Society
• /
• v.15 no.3
• /
• pp.380-387
• /
• 2012

The present investigation is to examine the thermal behaviors of air flows inside Korean traditional house made of the construction materials transmitted. The methodology is numerical predictions of air flows depend on the temperature distribution inside the indoor spaces. The transient computational simulations are performed along with the different house types, weather condition, and operating time. Thermal properties of building units have been obtained by the parallel measurements and utilized in the numerical works. Consequently, the details of flows and temperature of air in the houses illustrate the thermal design of the traditional Korean house satisfy the requirements of human living.

• Korean Journal of Construction Engineering and Management
• /
• v.4 no.4 s.16
• /
• pp.155-163
• /
• 2003

There are a growing number of cases to expand balconies of apartments faced with open air in order to enhance functional satisfaction and efficiency of dwelling space. In case of the balcony expansion at the floor, however, it is difficult to exclude a possibility of bringing about internal condensation due to the difference of temperature between indoor air and outdoor air caused by the Inflow of outer low-temperature air through the upper part of ceilings by failure in completely putting together the outer composite wall panels on the aluminum curtain walls installed at outer walls This study is to forecast possible occurrence of internal condensation around parapets and H-beam located at the inside of balcony ceilings on the uppermost floor of super-high apartment buildings faced with open air in order to provide dwellers with more comfortable environment in the related space and get rid of their uneasiness about the condensation. In this study, we estimated internal condensation, which vary in accordance with humidity pressure distribution, at curtain walls, stone panels or lower parts of slabs that constitute outer space of the residence and are weak against heat, through temperature forecast and temperature distribution interpretation program at normal two-dimension temperature

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.784_785
• /
• 2009

본 논문에서는 2[MVA]급 배전용 몰드변압기의 온도분포를 유한요소해석을 통하여 수행하였다. 몰드변압기의 온도상승한도와 허용최고온도를 전자기적 열원에 대한 분석을 통하여 계산하고 그 계산된 열원을 바탕으로 열적 해석의 열원으로 사용하여 계산하였다. 일반적으로 변압기의 수명은 내부의 전반적인 열적 특성보다는 특정 부위의 온도 분포에 의해 결정되며, 특히 변압기 내부 최고점의 온도(hot spot temperature)값이 허용치 이상으로 상승할 경우 절연내력의 저하로 인해 변압기의 수명은 급격히 감소한다. 이러한 수명개선을 위해 몰드 변압기의 철심과 고압.저압권선의 Joule's loss을 계산하여 열원을 계산하였고, 그 결과를 토대로 배전용 몰드변압기의 철심과 고압 저압권선의 온도상승 분포와 최고점의 온도분포를 예측하였다.