• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.18-18
• /
• 2010

전기적 에너지를 기계적 에너지로 변환하고 또한, 기계적 에너지를 전기적 에너지로 변환할 수 있는 압전 세라믹스는 압전 변압기 (piezoelectric transformer), 초음파 모터, 센서 등과 같은 응용분야에 광범위하게 사용되고 있다. 특히, 전원장치에 있어서 현재 주요 전자제품에 사용되고 있는 권선형 변압기와 같은 전자 변환기의 대체품으로 압전 세라믹스 소재의 특성을 이용한 압전변압기의 개발과 응용연구는 국내외적으로 활발히 연구되어왔다. 압전변압기는 권선형 변압기와 비교 하였을 때 누설자속이 없어 노이즈 발생이 없고, 공진주파수만을 이용하므로 출력의 파형이 정현파에 가까워 고조파 잡음이 없으며, 불연성의 특징을 가지고 있다. 추가적으로 압전 변압기는 소형화, 슬림화, 경량화가 가능하며 90%이상의 높은 효율을 얻을 수 있다. 또한, 단판형 압전변압기의 출력한계를 개선하기 위해 높은 승압비와 고출력을 갖는 적층타입의 압전변압기가 제안되었다. 압전변압기용 조성 세라믹스는 높은 에너지 변환효율을 위해서 전기기계결합계수 ($k_p$)가 커야 하며, 발열에 의한 온도 상승을 억제하기 위하여 기계적 품질계수(Qm)가 큰 것이 바람직하다. 또한, 높은 전류를 발생하기 위해서는 유전상수가 커 압전변압기의 출력측 정전용량을 크게 하여야한다. 이러한 압전변압기의 제작 조건을 위해 우수한 압전 및 유전특성을 갖는 PZT계 세라믹스가 주로 사용 되어져 왔다. 그러나, PZT계 세라믹스의 우수한 압전 및 유전특성에도 불구하고 $1000^{\circ}C$에서 급격히 휘발하는 PbO의 성질 때문에 환경적으로나 인체의 건강문제로 인해 전세계적으로 그 사용량을 제한하고 있다. 또한 적층 압전변압기의 구조적 특성상 내부전극과 함께 소결하여야 하는데, 이때 소결온도가 높으면 값비싼 Pd합량이 높은 전극을 사용하여야 한다. Pd함량이 10%미만인 Ag/Pd 전극을 사용하기 위해서는 $950^{\circ}C$ 이하에서 저온소결이 가능한 세라믹스 제조가 필수적이라 할 수 있다. 소결온도를 낮추는 방법으로는 다른 물질들을 치환하여 소결온도를 낮추는 방법과 미세분말을 만들어 그레인사이즈를 미세화 하는 방법들이 있다. 많은 미세 분말 제조 방법 중에서 Attrition mill은 일반적인 ball mill에 비해 분말의 입도를 미세하게 할 수 있어 증가된 분말의 비표면적에 의하여 반응을 촉진시킴으로써 저온소결이 가능한 세라믹스를 만들 수 있다. 따라서 본 연구에서는 소결온도가 낮으면서도 유전 및 압전특성이 우수한 조성을 사용하여 적층 압전변압기를 제작하여 전기적 특성을 조사하였다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.6
• /
• pp.42-48
• /
• 2002

The design, construction and performance test of a convenient multi-purpose irradiator is described. A multi-purpose irradiator using Cesium-137 has been developed for studies of low dose radiation effects in biology and for calibration of Thermo Luminescent dosimeter(TLD). During the operation, three rods of radioactive material which are 10cm in length revolve 180 degrees and irradiate biological samples, or TLD, and return to their shielded position, after the programmed time. A programmable Logic Controller(PLC) controls the sequence of operation, interlock, motor rotation and safety system. The rotation speed of biological samples can vary up to 20 RPM. A real time monitoring system was also incorporated to check and control the operation status of the irradiator. The capacity of the irradiation chamber was 4.5 liters. The isodose distribution at arbitrary vertical planes was measured by using film dosimetry. The dose-rate was 0.13 cGy/min in air and 0.11 cGy/min in water equivalent material in the case of Cesium-137. Range of activity was 2 Ci. The homogeneity of dose distribution in the chamber was ${\pm}$7%. The actual radiation level on the surface was within permissible levels. The irradiator had a maximum 0.35 mR/min radiation leakage on its surface.

• Journal of the Korean Institute of Gas
• /
• v.18 no.5
• /
• pp.47-51
• /
• 2014

This paper is to analyze and study the fire examples in respect of intake and exhaust, alternator tuning and inflow of inflammables on exhaust part in a car. In the first example, the driver diverted the intake and exhaust system for tuning of a car. Stopping a car to rest for moment, the flammable styrofoam scrap go into exhaust pipe that installed with exhaust manifold newly. It certified the fact that catched fire gradually, furthermore enlarged the fire by leaking fuel. In the second example, the driver enlarged the generator performance to divert the audio system in side room., it knew the fact that the electric wiring connected with generator gave the cause of outbreak a fire by overheating. In the third example, the serviceman replaced the engine oil using funnel-shaped, he put the a bottle of plastic pat onto engine cover carelessly. Consequentially, it found the fire occurrence in the engine room. Therefore, the driver never divert the intake and exhaust and generator construction of a car abnormally. Also, repairing and inspecting a car, the serviceman have a care to not occur the fire by inflammables.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.2
• /
• pp.176-183
• /
• 2014

Acoustic emission testing (AET) of cylinders is advantageous in that it can be directly conducted on cylinders installed in a car, without needing to dissemble them on a real-time basis. Therefore, users prefer AET over other nondestructive testing methods. Owing to these advantages of AET, it has been approved by the Department of Transportation of the U.S. as a safety evaluation method for pressure containers or as an alternative to the hydroproof testing method. This paper presents a study of the quantitative evaluation criteria for a container having ultrasonic testing defects and also for Type 1 and Type 2 gas cylinders, which are defective seamless pressure containers provided by NK, a manufacturer of pressure containers. For the Type 1 cylinder, the process from crack growth to leak was observed in a repetitive fatigue test using a 113 L container according to ASTM E 1419-02. Further, for the Type 2 cylinder, integrity was evaluated using a 119 L sound container and a container damaged by hydraulic pressure, by the slow-fill method according to ASTM E 2191-02. Based on the AET results of the Type 1 and Type 2 cylinders, quantitative evaluation criteria were established for a defective and non-defective container.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.5
• /
• pp.605-611
• /
• 2019

The fuel sloshing due to the rapid manoeuvre of the aircraft causes significant loads on internal components, which may break components or piping. In particular, a significant load is applied to the joint of the external fuel tank by sloshing movement, which may affect the safety of the aircraft when the joint of the external fuel tank is damaged. Therefore, in order to improve the survivability of aircraft and crew members, the design of external fuel tanks, and joints should be performed after evaluating the sloshing load through a numerical analysis of the fuel sloshing conditions. In this paper, a numerical analysis was performed on the sloshing test of the external fuel tank for rotorcraft. ALE (Arbitrary Lagrangian Eulerian) technique was used, and the test conditions specified in the U.S. Military Specification (MIL-DTL-27422D) was applied as the conditions for numerical analysis. As a result of the numerical analysis, the load on the joint of the external fuel tank was calculated. Moreover, the effects of sloshing movement on structural soundness were assessed through analysis of stress levels and margin of safety on metal fittings and composite containers.

• Journal of the Korean Institute of Gas
• /
• v.26 no.3
• /
• pp.54-59
• /
• 2022

This paper is a purpose to study and analyze the failure examples for timing belt, camshaft position sensor and ignition coil of LPG automotive engine. The first example, whe the service man install the front case bracket of engine, he excessively tightened up a 12mm bolt for being fixed of brackct. As a results, the bolt was separated from joint part so that it was put in between the crankshaft sprocket. Therefore the belt was broken off because of interference between timing belt and sprocket tooth. The second example, it verified the disharmony phenenomen of engine that the gap of the camshaft position sensor and camshaft senseing point assembled on cylinder head part was small more than iregular value so that the it was generated senseing damage phenomenon by pulse signal misconduct. The third example, it was found the engine disharmony phenomenon that the fire in the ignition coil was leaked by inner damage of Number 2 ignition coil.Therefore, the the manager of a car throughtly have to inspect not in order to arise the failure symptoms.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.85-89
• /
• 2021

AlGaN-based UV-C light-emitting diodes (LEDs) were applied for p-type activation by electrochemical potentiostatic activation (EPA). The p-type activation efficiency was increased by removing hydrogen atoms through EPA treatment using a neutral Mg-H complex that causes high resistance and low conductivity. A neutral Mg-H complex is decomposed into Mg^- and H⁺ depending on the key parameters of solution, voltage, and time. The improved hole carrier concentration was confirmed by secondary ion mass spectroscopy (SIMS) analysis. This mechanism eventually improved the internal quantum efficiency (IQE), the light extraction efficiency, the leakage current value in the reverse current region, and junction temperature, resulting in better UV-C LED lifetime. For systematic analysis, SIMS, Etamax IQE system, integrating sphere, and current-voltage measurement system were used, and the results were compared with the existing N₂-annealing method.

• Journal of the Korean Vacuum Society
• /
• v.16 no.6
• /
• pp.483-488
• /
• 2007

Current feeder system (CFS) for Korea superconducting tokamak advanced research(KSTAR) project plays a role to interconnect magnet power supply (MPS) and superconducting (SC) magnets through the normal bus-bar at the room temperature(300 K) environment and the SC bus-line at the low temperature (4.5 K) environment. It is divided by two systems, i.e., toroidal field system which operates at 35 kA DC currents and poloidal field system wherein 20$\sim$26 kA pulsed currents are applied during 350 s transient time. Aside from the vacuum system of main cryostat, an independent vacuum system was constructed for the CFS in which a roughing system is consisted by a rotary and a mechanical booster pump and a high vacuum system is developed by four cryo-pumps with one dry pump as a backing pump. A self interlock and its control system, and a supervisory interlock and its control system are also established for the operational reliability as well. The entire CFS was completely tested including the reliability of local/supervisory control/interlock, helium gas leakage, vacuum pressure, and so on.

• Journal of Radiation Protection and Research
• /
• v.31 no.4
• /
• pp.203-210
• /
• 2006

Purpose : To estimate the dose to the embryo/fetus of a pregnant patient with brain tumors, and to design an shielding device to keep the embryo/fetus dose under acceptable levels Materials and Methods : A shielding wall with the dimension of 1.55 m height, 0.9 m width, and 30 m thickness is fabricated with 4 trolleys under the wall. It is placed between a Patient and the treatment head of a linear accelerator to attenuate the leakage radiation effectively from the treatment head, and is placed 1 cm below the lower margin of the treatment field in order to minimize the dose to a patient from the treatment head. An anti-patient scattering neck supporters with 2 cm thick Cerrobend metal is designed to minimize the scattered radiation from the treatment fields, and it is divided into 2 section. They are installed around the patient neck by attach from right and left sides. A shielding bridge for anti-room scattered radiation is utilized to place 2 sheets of 3 mm lead plates above the abdomen to setup three detectors under the lead sheets. Humanoid phantom is irradiated with the same treatment parameters, and with and without shielding devices using TLD, and ionization chambers with and without a build-up cap. Results : The dose to the embryo/fetus without shielding was 3.20, 3.21, 1.44, 0.90 cGy at off-field distances of 30, 40, 50, and 60 cm. With shielding, the dose to embryo/fetus was reduced to 0.88, 0.60, 0.35, 0.25 cGy, and the ratio of the shielding effect varied from 70% to 80%. TLD results were 1.8, 1.2, 0.8, 1.2, and 0.8 cGy. The dose measured by the survey meter was 10.9 mR/h at the patient's surface of abdomen. The dose to the embryo/fetus was estimated to be about 1 cGy during the entire treatment. Conclusion : According to the AAPM Report No 50 regarding the dose limit of the embryo/fetus during the pregnancy, the dose to the embryo/fetus with little risk is less than 5 cGy. Our measurements satisfy the recommended values. Our shielding technique was proven to be acceptable.

• Korean journal of communication and information
• /
• v.43
• /
• pp.247-281
• /
• 2008

The purpose of this article is to re-examine the issue of Chobo's origin, which has not been clearly determinated thus far. Also, the research investigates Chobo's name, time point of discontinuance, character of the article on disaster, and civil-printed incident of Chobo during King Sunjo. As an internal bulletin, handwritten Chobo began to come out at the end of 15th century, roughly King Sungjong period of Chosun Dynasty. Systematically developed in the period of King Jungjong, it had continuously been released until November, 1907 when fairly organized and competitive commercial daily newspapers were published and when the office of secretary named Biseogam was abolished. Because handwritten Chobo was exclusive and narrow in its communication nature and difficult to read it's fast handwritten Nancho calligraphic style, in August, 1577 (10th year of King Sunjo) a few civilian in Seoul obtained a permission from authorities (Uijungboo and Sahunboo) published a wooden type printed Chobo. Unfortunately, privately printed Chobo was forced to cease in 3 month because of King Sunjo's oppressive measure. However, considering it was published for a profit by civilian and used the world's first type printing, it is highly probable that Chobo seems to be the world’s first type printing commercial daily newspaper.