• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.51-59
• /
• 2001

A diesel engine oil formulated in KRICT and a commercial diesel engine oil (API CG-4) were tested by car and their Kinematic Viscosity, TAN, TBN, metal content, additive depletion, anti-wear property and IR analysis were analyzed. From the research, both of the tested oils had almost the same properties f3r the change of TAN and TBN, but the change of Kinematic Viscosity of formulated oil was slightly higher than that of commercial oil. The iron content in the commercial oil increased rapidly from 7000 km while that of the formulated oil was still low. These results were confirmed by the anti-wear test with a 4-ball wear test machine for the each samples. Also, for the commercial oil, the depletion factor of the Zn-DTP which was added as an anti-wear property did not change any more after 7000 km. But, that of the formulated oil changed continuously to 8000 km, which means that the ability to prevent wear of the sliding pairs exists for the formulated oil. From the analysis results of oil properties obtained by field test, it was found that the commercial oil could be used only within 7000 km, but the formulated oil could be used more than 8000 km without severe wear of the sliding parts in the diesel engine.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.3 s.151
• /
• pp.481-486
• /
• 2006

There are attempts to utilize Hanji for apparel material, but, the reason that the strength and durability of Hanji decrease to a great extent in the wet condition, restricts the usability of Hanji. In order to improve the resistance against water, Hanji was treated with silicone type water repellent agents. The treatment was carried out by conventional pad-dry-cure method. The optimum treatment condition was obtained by varying the concentration of repellent agent, curing temperature and time. Water repellency was tested by spray rating method. Wet and dry tensile strength, tearing resistance and abrasion resistance were examined after the treatment. Flexural stiffness and wrinkle recovery angles of hanji were also measured. In result, the optimum condition of treatment was at resin concentration of 40g/l, catalyst concentration of 20g/l(half of resin concentration), curing temperature of 160$^{circ}C$, curing time of 120 sec. Flexural stiffness of Hanji was hardly increased and wrinkle recovery angle of Hanji was improved a little by resin treatment. After the treatment, in dry condition, tensile strength and tearing resistance were little changed but abrasion resistance was improved. In wet condition, tensile strength, tearing strength and abrasion resistance were improved.

• Journal of Energy Engineering
• /
• v.12 no.4
• /
• pp.302-308
• /
• 2003

The peformence tests of zinc-based desulfurization sorbents using the yellow earth as support for the hot gas clean up were carried out. The zinc-based sorbent with 25 wt％ yellow earth was prepared, and their properties such as the reaction rate, the sulfur capacity and the attrition resistance, were investigated. The reactivity tests for hot gas desulfurization was performed at middle temperatures (sulfidation/regeneration：480$^{\circ}C$/580$^{\circ}C$). During multi-cyclic desulfurization, the deactivation of zinc-based sorbent was decreased by the addition of yellow earth, and their efficiency was enhanced. The ZnO/yellow earth sorbent had high reactivity, good regenerability, long-term durability (about 19 gS/100 g sorbent for 10-cycles) and high attrition resistance (AI=19.1％). It was concluded that the peroperties of zinc-based sorbent were improved by metal oxides (Fe$_2$O$_3$, Na$_2$O, MnO$_2$, etc) in the yellow earth. From these results, it was confirmed that the desulfurization properties of zinc-based sorbents at middle temperatures could be improved by the yellow earth using as support.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.2
• /
• pp.296-304
• /
• 2014

For this research, prepared polyurethane dispersion of hard segment type and polyethylene emulsion wax. Use these resin, this article has been analyzed about mechanical properties variation by increasing amount of polyethylene emulsion wax on Lam skin leather and dried film. According to measure data for solvent resistance, PUD had good property. As known in the results, increase of polyethylene wax constant did not influence to big variation of hybrid resin properties. As test of tensile strength, PUD had good tensile characteristic($1.235kg_f/mm^2$) and PUD-EW4 had lowest tensile characteristic($1.022kg_f/mm^2$). As same as tensile characteristic, abrasion test determined PUD(52.225 mg.loss) had highest properties. In elongation case, PUD showed 698 % modulus which was best properties in this experiment.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.4
• /
• pp.618-625
• /
• 2012

In this study, prepared synthesis waterborne acrylic resin and water soluble milk casein resin. And than extent of casein contents in acrylic resin. We measured property of these samples by Lamb leather which is coated by acrylic-casein resins. According to measure data for solvent resistance, WAR resin and Hybrid resins had good property. Among this result knew that increase of casein constant did not influence to big change of hybrid resin property. As test of tensile strength, WAR had lowest strength($1.399kg_f/mm^2$) and WAC-3 had highest strength($1.426kg_f/mm^2$). Also we knew that best property of abrasion was WAC-3(69.774 mg.loss). In elongation case, WAR had best property(820%) in this experiment.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.628-634
• /
• 2014

In this study, a new paint which is able to resist the cavitation erosion is tried to be developed by using urethane added with polyol such as poly propylene glycol(PPG), poly carbonate diol(PCD), polycaprolactone polyol (PCL-1), and poly caprolactone-tetramethylene gylcolether polyol(PCL-2). The new paint synthesized by adding polyol was characterized with physical properties and resistivity to cavitation erosion. Among polyol, the prepolymer added with PCD showed high hardness and wear resistance. However, due to too high in viscosity, the prepolymer added with PCL-1 was selected as a paint. The paint added with PCL-1 showed high resistivity to cavitation erosion and its surface was monitored by using Scanning Electron Microscope.

• Elastomers and Composites
• /
• v.33 no.4
• /
• pp.231-237
• /
• 1998

In order to investigate the physical properties of rubber blend compound, this experiment was carried out on the cure rate, loss tangent, reinforcement and abrasion properties of S-SBR (solution styrene-butadiene rubber) blends containing silane coupled silica and E-SBR (emulsion styrene-butadiene rubber) blends containing carbon black as a model compound. E-SBR blend showed the highest total bound rubber(TBR), while S-SBR blends showed constant TBR level regardless of rubber type. Rapid cure rate was achieved when the styrene and vinyl content of rubber microstructure decreased and TBR content of rubber compounds increased. The modulus as the index of rubber reinforcement showed the linear relation with TBR content. The large amount of PICO loss was observed when the styrene and vinyl content of rubber microstructure increased, while the small amount of PICO loss was observed when the ratio of bu-tadiene increased in the S-SBR blends with silane copuled silica. The high loss tangent at $0^{\circ}C$, the low loss tangent at $60^{\circ}C$, and the large difference of loss tangent were shown in the S-SBR blends with high styrene content compared to E-SBR blend.

• The korean journal of orthodontics
• /
• v.27 no.4 s.63
• /
• pp.549-557
• /
• 1997

This study was designed to investigate the attrition pattern in Angle Class III malocclusion with facial asymmetry. The sample consisted of three groups, the 20 subjects of normal occlusion group(Group I), the 12 subjects of class III malocclusion without facial asymmetry group(Group II) and 17 subjects of Class III malocclusion with facial asymmetry group(Group III). Attrition areas from canine to second molar on both sides in upper and lower arch, totally twenty, was marked by pencil and mesured by computer system(INTERGRAPH CO. USA) 2 times and the average value was used for date processing. Attrition areas from canine to second molar on both sides in upper and lower arch, totally twenty, was marked by pencil and mesured by computer system(INTERGRAPH CO. USA) 2 times and the average value was used for date Processing. All attrition areas were measured 2 times and the average value was used for data processing The data were statistically analyzed by SAS program. The results of this study were as follows. 1. Total attrition area in Group I was larger than in Group II and III. 2. There was no significant difference in attrition area between right and left side in each group, but attrition area in Group III was larger than in Group I and II. 3. In Group I, Maxillary attrition area was larger than mandibular attrition area, but in Group ll and III, there was no significant difference in attrition area between maxilla and mandible. 4. In Group III, the attrition area of deviated side was target than undeviated side 5. There was no significant difference in attrition area between chewing side and non-chewing side in each group. 6. The total attrition area was unaffected by gender.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.35 no.1
• /
• pp.110-117
• /
• 2008

Clinical performance of resin-based composite material depends on case selection and on the proficiency of the operator. Especially, composite resin restoration on permanent first molar in children have more limitations clinically than adult patients according to stage of tooth eruption and patient's compliance. This study was designed to evaluate the clinical performance of posterior composite resin restoration in children after 5 years. 35 teeth of 16 patients who were received composite resin restoration on permanent first molar in Department of Pediatric dentistry, Pusan National University Hospital between January 2001 and December 2001 were evaluated based on Modified USPHS criteria. From the finding in this study, following conclusions can be made. 1. 6 teeth(17%) of 35 teeth was replaced, so 5-years survival rate of posterior composite resin restoration is 82.9%. 2. As results of each evaluation criteria, on color match, anatomic form, surface roughness, sensitivity/ discomfort, ideal A grade score was 86.2%, 93.1%, 86.2%, 86.2%, clinically accepted B grade score was 13.8%, 0%, 13.8%, 10.3%. On marginal adaptation and marginal discoloration, A grade score was 13.8%, 44.8% and B grade score was 79.3%, 34.5% and secondary caries rate was 20.7%. 3. 69.1% of teeth (20 teeth) was clinically accepted on all evaluation criteria.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.36 no.2
• /
• pp.305-309
• /
• 2009

Dens evaginatus is a dental anomaly most commonly seen in premolar teeth in which a tubercle or protuberance projects from either the center of the occlusal surface or the buccal triangular ridge. These tubercles are easily fractured from mastication as the tooth erupts and frequently leads to pulp necrosis as a common complication. To prevent these sequelae, prophylactic treatment soon after the tooth starts erupting is essential. These preventive treatments include, selective grinding and protection of the tubercle by pit and fissure sealant. When the tooth does shows signs of pulp necrosis and apical periodontitis, endodontic procedures are needed. Apexification and apexogenesis are usually the treatment of choice for the affected teeth which have immature apices. Apexogenesis is a vital pulp therapy procedure performed to encourage continued physiological development and formation of the root end. It involves removal of the inflamed pulp and the placement of calcium hydroxide on the remaining healthy pulp tissue. This case report describes an atypical apexogenesis of a mandibular premolar which showed to be a dens evaginatus. The tooth which was treated with calcium hydroxide shows good results and is planned for permanent root canal filling.