• Journal of Sericultural and Entomological Science
• /
• v.32 no.1
• /
• pp.68-72
• /
• 1990

The color fastness of Korean silk fabrics was measured in this investigation. The sample fabrics under examination were divided into four groups, according to the processing cycle: 1) Plain dyeing(A-C) : 2) Yarn dyeing(D;E=Knitted fabric) ; 3) Direct printing(F-H) ; 4) Discharge Printing(I-P) : The following result can be obtained. Among the samples examined, both the plain-dyed(brilliant colours) and discharge-printed (put-in colours) fabrics show lower values of water, perspiration and ironing color fastness compared with those recommended by International Organization for Standardization(I. S. O.)

• Journal of the Korean Society of Clothing and Textiles
• /
• v.38 no.1
• /
• pp.73-86
• /
• 2014

Persimmon juice dye-printed fabrics with printing were used for a Galot one-piece dress. The Galot dress was assessed in comparison to a white undyed one-piece dress of the same design through a wearing test conducted in a climatic chamber with an air temperature of $30{\pm}1^{\circ}C$, $50{\pm}5%$ R.H, and 0.2m/sec air movement on 4 healthy female subjects in their 20s. The subjects went through a 30-min stable period, a 30-min exercise of walking on a $5^{\circ}$ slope treadmill at 70m/min period, and a 20-min recovery period. In addition, a physiological reaction and subjective sensation were estimated. The results showed that significant differences were mostly observed from a sweating period that occurred during the latter half of the exercise. More specific results are as follows. First, skin temperature on the chest and mean skin temperature were significantly higher (p<.01) in rayon dyed sample dresses. Second, micro-humidity on the back showed a significant difference (p<.01). Both cotton and rayon persimmon juice dyed sample dresses produced lower microhumidity than their counterparts and as for cotton the difference occurred over the entire experimental period; however, it occurred after the middle of the exercise period for rayon. Third, the sweating rate on the back decreased in both cotton and rayon with persimmon juice dye but no significant difference was observed. Fourth, subjective three sensations revealed significant differences between cotton and rayon (p<.01), indicating that the subjects felt more cool, dryer and more comfortable in a cotton Galot. As described above, the analysis of physiological responses and the subjective sensation of undyed and dyed clothing shows the effect of persimmon juice dyeing. Persimmon juice dyeing also seemly increased air permeability, moisture regain and permeability facilitating body heat ventilation, as micro-humidity and sweat rate were lowered. However, this was not shown consistently in subjective responses on comfort especially when wearing rayon dresses.

• Journal of the Korean Home Economics Association
• /
• v.38 no.9
• /
• pp.119-130
• /
• 2000

The purpose of this study was to confirm the possibility of screen printing with Natural dyes. The coloring matter such as sappan wood was used in order to obtain the colorant powder through the processes of extraction, low pressure concentration and the spray dry. After the screen printing on silk and cotton fabrics with colorant, K/S value changes of color and color fastness were measured. The main resets were as follows : 1. The viscosity of printing thickeners of sappan wood powder was about 15,200 cps, and the highest K/S value of the fabrics printed with sappan wood was obtained at 90$\pm$2$\^{C}$ of steaming temperature and 80 minutes of steaming time. 2. For the fabrics printed with sampan wood, adding of urea was not effective, since the more the concentration of urea increased, the more K/S values decreased. 3. For the natural dyes printing, the more the concentration of colorants increased, the more K/S values increased. In general, the K/S values of the printed fabrics were higher when treated with mordants rather than without mordants. Specifically, the λmax sappan wood was 520∼570 nm, and the K/S value was highest when treated with Cu mordant and lowest when treated with Sn. 4. Generally, the color fastness was relatively fair.

• Textile Coloration and Finishing
• /
• v.6 no.2
• /
• pp.30-39
• /
• 1994

To study the printing behaviors of Polyester and cotton(P/C) fabrics printed with disperse and reactive dyes, the effects of alkalis on the fixation of reactive dyes and the alkali-stability of disperse dyes in various methods of fixation were examined. The anthraquinone disperse dyes which have diamino derivatives as substituents without hydroxy group, such as C.I. Disperse Violet 1(D.V.1), C.I. Disperse Violet 28(D.V.28) and C.I.Disperse Blue 60(D.B.60) showed good results of fixation without regard to the concentration of NaHCO$_3$. In case of high temperature steaming(HTS) and unsaturated steaming(US)/HTS, D.V. 1 was alkali-stable and effective for P/C printing. A good result was obtained with D.V.1 and C.I.Reactive Orange 13(R.O.13) paste of 4% $K_{2}CO_{3}$. It was found that the unfixed D.V.28 bearing chloro group can hinder the fixation of monochlorotriaxinyl reactive dyes, and D.B.60 made little stain on 100% cotton. In thermosol(Tm), the dye uptake of D.V.1 was not decreased so much, but those of D.V.28 and D.B.60 were greatly decreased.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.86-86
• /
• 2011

나노소재기술은 기존 소재로는 얻을 수 없는 새로운 기능 및 특성을 나타낼 수 있어 산업전반에 적용할 수 있는 최첨단집적기술이다. 그러나 나노입자를 섬유에 첨가하여 기능성 섬유를 생산하는 경우 응집이 발생하는 등의 다양한 문제점이 발생하는데 이를 극복하기 위해서는 사이즈 분포를 제어하는 기술, 표면처리를 통해 분산성을 향상시키는 기술, 나노입자와 섬유와의 상용성을 개선하는 기술 등이 해결되어야 한다. 본 연구에서는 고기능성 및 고부가가치 경편파일 니트 원단을 개발하기 위해 은(Silver) 나노입자가 균일하게 분산된 M/B(Master Batch)를 제조하였으며, 이를 PET와의 용융 혼합 방사함으로써 0.5denier(75D/144F)급 원사에 99.9%의 영구적인 항균/소취 기능을 부여하였다. 또한 개발된 극세사를 이용하여 다양한 경편파일 원단을 설계하고, 기모, 염색 및 날염 등의 공정을 거쳐 나노기술융합형 화학섬유소재를 이용한 기능성 침장 제품을 개발하였다.

• Textile Coloration and Finishing
• /
• v.11 no.5
• /
• pp.13-21
• /
• 1999

In this study, selected cotton fabrics and polyester/cotton(P/C) blended fabrics are treated with a soluble polyurethane(SPU) and then, printed by heat transfer to determine the effect of SPU treatment on dye uptake of the samples. The results obtained are as follows： 1) In heat transfer, dye-uptake gets higher in Vopotion to temperature and time. The optimum printing temperature and printing time of C.I. Disperse Orange 3 and C.I. Disperse Violet 1 are $200^\circ{C}$ and 50sec. 2) Dye-uptake gets higher according to SPU concentration ; both cotton and P/C fabrics show the highest at $100g/\ell$. 3) In color, as temperature, time and SPU concentration increase, P/C fabrics show more yellowish orange color than cotton fabrics in case of C.I. Disperse Orange 3 and P/C fabrics show more reddish violet color than cotton fabrics in case of C.I. Disperse Violet 1. 4) All fastness of cotton and P/C fabrics treated with SPU are good, but color fastness to washing and water of cotton fabrics treated with SPU are not good.

• Fashion & Textile Research Journal
• /
• v.6 no.5
• /
• pp.667-672
• /
• 2004

Poly(ethylene terephthalate) (PET) fabrics were treated with a silica particle and phosphate flame retardant to determine the optimum process condition of the digital textile printing(DTP) media. The treating conditions for the study were 6 conditions, from F1 to F6, in which F3, F4 and F5 were treated with mixture of both silica particle and phosphate compound in process of pad, dry and cure fixation. F6 was treated with phosphate compound only and silica particle coating successively. Xanthan gum was used to control the migration of liquid phosphate compound onto PET fabrics. The change in surface morphology of fabrics treated with silica particle and phosphate compound was observed by SEM and flame retardance was evaluated by limiting oxygen index(LOI). It was observed that F6 was the excellent flame retardance and low bleeding in printing, Collectively, the printing characteristics of silica to cyan, magenta, yellow and black ink and flame retardance of fabrics finished with phosphate compound were identified in this study.

• Textile Coloration and Finishing
• /
• v.26 no.1
• /
• pp.13-21
• /
• 2014

The object of this research is to perform the basic research for the development of selectively permeable membrane fabrics which is suitable for korean military in sense of embattlement. As a key factor of selectively permeable membrane fabrics which is suitable for korean military, this study selected the best PVA thickness and membrane selection for DMMP protection, pre-treatment method for conformational stability of face fabric and water/oil repellent process condition. Especially as the PVA coating thickness of the fabrics increase, peneration of DMMP decrease including water vapor permeation is lower. This study shows how physical features and permeability of chemical agents can be influenced by pre-treatment methods, the selection of selectively permeable membrane, the thickness of PVA etc. Results showed that outer shell / PVA / e-PTFE materials possessed performance with superior water vapor permeation (Over $3,000g/m^2/day$) and protective capability against DMMP vapor ($0.6{\mu}g/cm^2{\cdot}16hr$).

• Journal of Sensor Science and Technology
• /
• v.27 no.6
• /
• pp.421-426
• /
• 2018

To develop a piezoelectric inkjet printhead for high-resolution and high-speed printing, we studied the characteristics of an inkjet printhead by analyzing the major design parameters. An analytical model for the inkjet printhead was established, and numerical analysis of the coupled first-order differential equation for the defined state variables was performed using state equations. To design the dimension of the inkjet printhead with a driving frequency of 100 kHz, the characteristics of the flow rate and discharge pressure of the nozzle were analyzed with respect to design variables of the flow chamber, effective sound wave velocity, driving voltage, and voltage waveform. It was predicted that the change in the height of the flow chamber does not significantly affect the Helmholtz resonance frequency and discharge speed of the nozzle. From the analysis of change in flow chamber width, it is observed that as the width of the flow chamber increases, the ejection speed greatly increases and the Helmholtz resonance frequency decreases considerably, thereby substantially affecting the performance of the inkjet printhead.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.95-95
• /
• 2011

가방지 중에서 고급 브랜드의 핸드백은 근래의 세계적인 경기불황에서도 꾸준한 소비층을 형성하면서 매출 상승을 유도하고 있는데, 기존 40~50대 시니어들을 위한 전통적인 레자 또는 자카드 문양직물의 고유한 디자인 뿐만 아니라 20~30대의 젊은 층을 위한 다양한 칼라의 프린팅 문양 직물도 많이 개발되고 있는 실정이다. 본 연구는 잠재권축사와 고강력PET를 이용하여 이소재 복합 ATY를 제조하고 제직 및 날염을 통해 다양한 프린팅 문양을 발현할 수 있는 가방지용 직물 개발에 관한 것이다. 최근의 캐주얼 및 힙합룩은 물론, 베이직 정장 차림까지 트렌디한 우븐 백이 코디 아이템 1호로 떠오르고 있는데, 가방용 브랜드 중"레스포색"과 "키플링" 등이 급상승 기류를 타며 국내에 빠르게 정착하고 있으며 수입 브랜드인 경전상사의 "롱샴"도 폴딩백으로 인기를 누리고 있다. 핫 이슈인 스포티즘을 떠올리지 않더라도 최근의 변화는 소비자의 니즈를 적극 수용하려는 패션잡화 업체들의 움직임을 대변하고 있으며, 직물형태의 백이 합리적인 가격에서나 가볍고 편리한 실용적인 부분 모두 소비자의 니즈를 채워주기에 충분하고, 트렌드가 부각된 가방일수록 시즌에 따라 스피디하게 구매가 이뤄지고 있다는 장점이 있어서, 최신 트렌드의 디자인과 재료 효과를 극대화한 제품이 다수 선보이고 있다. 본 연구에서는 이러한 다양한 트렌드 디자인의 문양 발현을 위한 직물을 위해 PET Base의 잠재권축사와 PET 고강력사를 사용하였는데, 이때 사용되는 잠재권사는 Effect사로써 온도, Air압 등의 공정요소 제어를 통해 Soft한 touch을 위한 잔루프를 발현하도록 하였으며, PET 고강력사는 Core사로 사용함으로써 잠재권축사의 강도를 보강하여 가방지로써 요구되는 강력을 가질 수 있도록 하였다.