• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.3
• /
• pp.46-55
• /
• 2016

This work proposes a 13b 100MS/s 45nm CMOS ADC with a high dynamic performance for IF-domain high-speed signal processing systems based on a four-step pipeline architecture to optimize operating specifications. The SHA employs a wideband high-speed sampling network properly to process high-frequency input signals exceeding a sampling frequency. The SHA and MDACs adopt a two-stage amplifier with a gain-boosting technique to obtain the required high DC gain and the wide signal-swing range, while the amplifier and bias circuits use the same unit-size devices repeatedly to minimize device mismatch. Furthermore, a separate analog power supply voltage for on-chip current and voltage references minimizes performance degradation caused by the undesired noise and interference from adjacent functional blocks during high-speed operation. The proposed ADC occupies an active die area of $0.70mm^2$, based on various process-insensitive layout techniques to minimize the physical process imperfection effects. The prototype ADC in a 45nm CMOS demonstrates a measured DNL and INL within 0.77LSB and 1.57LSB, with a maximum SNDR and SFDR of 64.2dB and 78.4dB at 100MS/s, respectively. The ADC is implemented with long-channel devices rather than minimum channel-length devices available in this CMOS technology to process a wide input range of $2.0V_{PP}$ for the required system and to obtain a high dynamic performance at IF-domain input signal bands. The ADC consumes 425.0mW with a single analog voltage of 2.5V and two digital voltages of 2.5V and 1.1V.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.5
• /
• pp.399-407
• /
• 2009

Laser induced breakdown spectroscopy(LIBS) is an simple analysis method for directly quantifying many kinds of soil micro-elements on site using a small size of laser without pre-treatment at any property of materials(solid, liquid and gas). The purpose of this study were to find an optimum condition of the LIBS measurement including wavelengths for quantifying soil elements, to relate spectral properties to the concentration of soil elements using LIBS as a simultaneous un-breakdown quantitative analysis technology, which can be applied for the safety assessment of agricultural products and precision agriculture, and to compare the results with a standardized chemical analysis method. Soil samples classified as fine-silty, mixed, thermic Typic Hapludalf(Memphis series) from grassland and uplands in Tennessee, USA were collected, crushed, and prepared for further analysis or LIBS measurement. The samples were measured using LIBS ranged from 200 to 600 nm(0.03 nm interval) with a Nd:YAG laser at 532 nm, with a beam energy of 25 mJ per pulse, a pulse width of 5 ns, and a repetition rate of 10 Hz. The optimum wavelength(${\lambda}nm$) of LIBS for estimating soil and plant elements were 308.2 nm for Al, 428.3 nm for Ca, 247.8 nm for T-C, 438.3 nm for Fe, 766.5 nm for K, 85.2 nm for Mg, 330.2 nm for Na, 213.6 nm for P, 180.7 nm for S, 288.2 nm for Si, and 351.9 nm for Ti, respectively. Coefficients of determination($r^2$) of calibration curve using standard reference soil samples for each element from LIBS measurement were ranged from 0.863 to 0.977. In comparison with ICP-AES(Inductively coupled plasma atomic emission spectroscopy) measurement, measurement error in terms of relative standard error were calculated. Silicon dioxide(SiO2) concentration estimated from two methods showed good agreement with -3.5% of relative standard error. The relative standard errors for the other elements were high. It implies that the prediction accuracy is low which might be caused by matrix effect such as particle size and constituent of soils. It is necessary to enhance the measurement and prediction accuracy of LIBS by improving pretreatment process, standard reference soil samples, and measurement method for a reliable quantification method.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.25 no.4
• /
• pp.94-106
• /
• 2022

In order to increase timber self-sufficiency, Korea's 6th Basic Forest Plan aims to increase the density of forest roads to 12.8 m ha^-1 by 2037. However, due to rapid re-forestation, current management infrastructure is insufficient, with just 4.8 m ha^-1 of forest roads in 2017. This is partly due to time and cost limitations on the process of forest road feasibility evaluation, which considers factors such as topography and forest conditions. To solve this problem, we propose an eco-friendly and efficient forest road network planning method using a geographic information system (GIS), which can evaluate a potential road site remotely based on spatial information. To facilitate such planning, this study identifies forest road construction priorities that can be evaluated using spatial information, such as topography, forest type and forest disasters. A method of predicting the optimal route to connect a forest road with existing roads is also derived. Overlapping analysis was performed using GIS-MCE (which combines GIS with multi-criteria evaluation), targeting the areas of Cheongsong-gun and Buk-gu, Pohang-si, which have a low forest-road density. Each factor affecting the suitability of a proposed new forest road site was assigned a cost, creating a cost surface that facilitates prioritization for each forest type. The forest path's optimal route was then derived using least-cost path analysis. The results of this process were 30 forestry site recommendations in Cheongsong-gun and one in Buk-gu, Pohang-si; this would increase forest road density for the managed forest sites in Cheongsong-gun from 1.58 m ha^-1 to 2.55 m ha^-1. This evaluation method can contribute to the policy of increasing timber self-sufficiency by providing clear guidelines for selecting forest road construction sites and predicting optimal connections to the existing road network.

• Korean journal of applied entomology
• /
• v.61 no.2
• /
• pp.335-347
• /
• 2022

We investigated the emergence patterns of Chilo suppressalis (Lepidoptera: Crambidae) adults using sex pheromone traps in the three northeastern areas, Dandong (40°07'N 124°23'E) (Liaoning province), and Gongzhuling (43°30'N 124°49') and Longjing (42°46'N 129°26'E) (Jilin province), China, in 2020 and 2021. Two times of adult flight seasons were isolated clearly during the rice growing periods in the all areas, in which the first season from mid May to late July, and the second season from mid July to mid September were observed. The adult emergence seasons in the areas at higher latitude were later than that at lower latitude. Using the adult emergence data during the first flight seasons, the second flight seasons were estimated through insect phenology modelling, and compared with the observed data. Temperature-dependent life history models (developmental rate, development completion, survival rate, adult aging rate, total fecundity, oviposition completion, and adult survival completion) were collected or constructed for each life stage of C. suppressalis, in which the data from the four previous studies were used. Those models were combined in an insect phenology estimation software, PopModel, and operated for the observed areas. In the results, the phenology modelling operated with the models based on the data of shorter larval periods in the previous studies estimated more accurately the second flight seasons. In 2021, we investigated the change of damaged hill ratios of rice with observing the adult emergence at Dandong and Longjing, 2021. The increase periods of damaged hill ratios of rice were observed two times during the total rice cultivation season, which may be caused by different generations of C. suppressalis larvae.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.1
• /
• pp.172-191
• /
• 2023

This study was undertaken to strategize the mixed traffic operation of autonomous vehicles in the pilot zone. This was achieved by analyzing the changes expected when autonomous vehicles are mixed in the autonomous vehicle pilot zone. Although finding a safe and efficient traffic operation strategy is required for the pilot zone to serve as a test bed for autonomous vehicles, there is no available operation strategy based on the mixture of autonomous vehicles. In order to presents a traffic operation strategies for each period of autonomous vehicle introduction, traffic efficiency and safety analysis was performed according to the autonomous vehicle market percentage rate. Based on the analysis results, the introduction stage was divided into introductory stage, transition period, and stable period based on the autonomous vehicle market share of 30% and 70%. This study presents the following traffic operation strategies. Considering the traffic flow operation strategy, we suggest the advancement of the existing road infrastructure at the introductory stage, and operating an autonomous driving lane and the mileage system during the transition period. We also propose expanding the operation of autonomous driving lanes and easing the speed limit during the stable period. In the traffic safety strategy, we present a manual and legal system for responding to autonomous vehicle accidents in the introductory stage, an analysis of the causes of autonomous vehicle accidents and the implementation of preventive policies in the transition period, and the advancement of the autonomous system and the reinforcement of the security system during the stable period. Through the traffic operation strategy presented in this study, we foresee the possibility of preemptively responding to the changes of traffic flow and traffic safety expected due to the mixture of autonomous vehicles in the autonomous vehicle pilot zone in the future.

• Analytical Science and Technology
• /
• v.20 no.4
• /
• pp.308-314
• /
• 2007

The analytical method of HPLC with the radial-flow electrochemical cell (RFEC) has been developed to determine doxorubicin, epirubicin, nogalamycin, daunorubicin and idarubicin simultaneously by employing a reversed-phase chromatography. Anthracyclines were detected at -0.74 V vs. a Ag/AgCl (0.01 M NaCl) reference electrode, a potential of diffusion current plateau in the mobile phase. At a $V_f$ of 1.0 mL/min doxorubicin, epirubicin, daunorubicin and idarubicin appeared at a retention time ($t_r$) of 6.4 min, 7.4 min, 12.7 min and 18.4 min, respectively, while at a $V_f$ of 0.6 mL/min, doxorubicin, epirubicin, nogalamycin, daunorubicin and idarubicin appeared at a $t_r$ of 9.9 min, 11.5 min, 13.5 min, 19.6 min and 28.7 min, respectively. The linearity between each anthracycline injected ($2.40{\times}10^{-7}M{\sim}1.42{\times}10^{-5}M$) and peak area (charge) was excellent with the square of the correlation coefficient ($R^2$) higher than 0.999. The detection limits were $1.0{\times}10^{-8}M{\sim}1.5{\times}10^{-7}M$ for the five anthracyclines. Within-day precision for the five anthracyclines were in reasonable relative standard deviations less than 3 % ($1.00{\times}10^{-6}M{\sim}1.42{\times}10^{-5}M$) except the lower concentrations less than $0.7{\mu}M$. Solid phase extractions of $1.00{\times}10^{-5}M$ epirubicin, $0.48{\times}10^{-5}M$ nogalamycin and $1.52{\times}10^{-5}M$ daunorubicin from human serum with a $C_{18}$ cartridge resulted in 97 %, 100 % and 90 % of recoveries, respectively.

• Korean journal of applied entomology
• /
• v.62 no.3
• /
• pp.183-191
• /
• 2023

After examining the temperature change in berry sawdust during the fermentation period and the developmental characteristics of Protaetia brevitarsis larvae according to the fermentation period, it was found that the fermentation speed was faster than with oak sawdust and a fermentation period of 50-70 days was the most suitable for larval growth. During the fermentation period, the temperature change in sawdust was quickly fermented as berry sawdust passed a high temperature of more than 60℃ in the early stages of fermentation compared to fermentation speed of oak sawdust, and stabilized within 60 days. In individual breeding, the total growth period of P. brevitarsis larvae by fermentation period was the longest at 104.8 days after fermentation for 30 days, which was a significant difference. There was no difference in the growth period between 50 and 90 days of fermentation. Oak sawdust tended to be the same as berry sawdust, but the larval development period was approximately 30 days. The developmental period by larval stage differed greatly between berries and oak sawdust. The weight of larvae according to the fermentation period of sawdust was the lowest after 90 days of fermentation, with a long fermentation period for both berry and oak sawdust, and there was no difference in the 30-70 days fermentation periods. The survival rate was more than 95% in individual breeding, and there was no difference among the fermentation periods. However, in group breeding, the survival rate was lower than that of individual breeding and was lowest at 90 days of fermentation. In group breeding, the ratio of larvae weighing ≥ 2.5 g, which is the standard for shipment, was 85% after 30-70 days of fermentation of berry sawdust, but was lower at 70% after 90 days of fermentation, which was a significant difference. The survival rate with oak sawdust showed the same trend, which was approximately 10% lower than that with sawdust. In addition, the larvae from the berry sawdust weighed > 2.5 g in 40-60 days, while it took 75-105 days with oak-fermented sawdust.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.18 no.3
• /
• pp.191-209
• /
• 2023

Amid rapid changes in technological innovation due to the influence of the 4th Industrial Revolution and COVID-19, research related to absorption capacity and patent activities to promote technological innovation of Korean technology start-ups is important in this uncertain environment. This study aims to examine the effects on entrepreneurial performance and patent activities by reconstructing absorptive capacity, an organizational capability, for technology-based startups in fields such as BT and ICT with less than seven years of establishment, distinguishing between potential absorptive capacity and realized absorptive capacity. The study also seeks to develop a theoretical research model. To accomplish this, data was collected from managerial executives, including CEOs of 215 technology startups. The following hypotheses were tested: Firstly, potential absorptive capacity had a significant impact on patent activities, while realized absorptive capacity did not. Secondly, potential absorptive capacity had a significant impact on technological performance, while realized absorptive capacity did not. Thirdly, both potential and realized absorptive capacity had a significant impact on financial and non-financial performance. Fourthly, patent activities indirectly influenced potential absorptive capacity and technological performance, but did not affect realized absorptive capacity. Fifthly, patent activities indirectly influenced potential absorptive capacity and financial performance, but did not affect realized absorptive capacity. Lastly, patent activities indirectly influenced potential absorptive capacity and non-financial performance, but did not affect realized absorptive capacity. The practical significance of this study lies in providing useful guidelines for building the core capabilities of organizations through absorptive capacity and patent activities. Furthermore, it is expected that startups that have not recognized the formation process of absorptive capacity for patent activities will perceive the formation mechanism of absorptive capability anew and show considerable interest in future potential and realized absorptive capacity as part of their management strategies. This is anticipated to play an important role in adapting to rapidly changing technological advancements, the startup ecosystem, and securing sustainable competitive advantages.

• Journal of the Society of Disaster Information
• /
• v.20 no.2
• /
• pp.339-350
• /
• 2024

Purpose: This study analyzes accessibility of 10 hydrogen charging stations in Seoul and identifies areas that were difficult to access. The purpose is to re-analyze accessibility by adding a new location in terms of equity and safety of location placement, and then draw implications by comparing the improvement effects. Method: By applying the location-allocation model and the service area model based on network analysis of the ArcGIS program, areas with weak access were identified. The location selection method applied the 'Minimize Facilities' method in consideration of the need for rapid arrival to insufficient hydrogen charging stations. The limit distance for arrival within a specific time was analyzed by applying the average vehicle traffic speed(23.1km/h, Seoul Open Data Square) in 2022 to three categories: 3,850m(10minutes), 5,775m(15minutes), 7,700m(20minutes). In order to minimize conflicts over the installation of hydrogen charging stations, special standards of the Ministry of Trade, Industry and Energy applied to derive candidate sites for additional installation of hydrogen charging stations among existing gas stations and LPG/CNG charging stations. Result: As a result of the analysis, it was confirmed that accessibility was significantly improved by installing 5 new hydrogen charging stations at relatively safe gas stations and LPG/CNG charging stations in areas where access to the existing 10 hydrogen charging stations is weak within 20 minutes. Nevertheless, it was found that there are still areas where access remains difficult. Conclusion: The location allocation model is used to identify areas where access to hydrogen charging stations is difficult and prioritize installation, decision-making to select locations for hydrogen charging stations based on scientific evidence can be supported.

• Journal of Internet Computing and Services
• /
• v.25 no.1
• /
• pp.99-107
• /
• 2024

Along with economic growth and industrial development, there is an increasing demand for various electronic components and device production of semiconductor, SMT component, and electrical battery products. However, these products may contain foreign substances coming from manufacturing process such as iron, aluminum, plastic and so on, which could lead to serious problems or malfunctioning of the product, and fire on the electric vehicle. To solve these problems, it is necessary to determine whether there are foreign materials inside the product, and may tests have been done by means of non-destructive testing methodology such as ultrasound ot X-ray. Nevertheless, there are technical challenges and limitation in acquiring X-ray images and determining the presence of foreign materials. In particular Small-sized or low-density foreign materials may not be visible even when X-ray equipment is used, and noise can also make it difficult to detect foreign objects. Moreover, in order to meet the manufacturing speed requirement, the x-ray acquisition time should be reduced, which can result in the very low signal- to-noise ratio(SNR) lowering the foreign material detection accuracy. Therefore, in this paper, we propose a five-step approach to overcome the limitations of low resolution, which make it challenging to detect foreign substances. Firstly, global contrast of X-ray images are increased through histogram stretching methodology. Second, to strengthen the high frequency signal and local contrast, we applied local contrast enhancement technique. Third, to improve the edge clearness, Unsharp masking is applied to enhance edges, making objects more visible. Forth, the super-resolution method of the Residual Dense Block (RDB) is used for noise reduction and image enhancement. Last, the Yolov5 algorithm is employed to train and detect foreign objects after learning. Using the proposed method in this study, experimental results show an improvement of more than 10% in performance metrics such as precision compared to low-density images.