• Korean Journal of Agricultural Science
• /
• v.27 no.1
• /
• pp.39-47
• /
• 2000

A large scale field test of prefabricated vertical drains is performed to analyze the effect of parameters of the very soft clay at a test site. Compression index and the coefficient of horizontal consolidation obtained by back-analysis from the settlement data were compared with those obtained by means of laboratory tests. The Hyperbolic, Asaoka's and The Curve fitting methods are used to estimate final settlements and coefficients of consolidation. 1. Final settlement predicted with the Hyperbolic method was the largest, and the settlements predicted with the Asaoka's and the Curve fitting methods were nearly the same range, and it was concluded that smear effect has to be considered on design in the case that spacing of drains is small 2. The relationships of the measured consolidation ratio (Urn) and the designed consolidation ratio($U_t$) were showed as $U_m$ = (1.13~1.17)$U_t$, $U_m$ = (1.07~1.20)$U_t$, $U_m$ = (1.13~1.17)$U_t$ on the Hyperbolic, Asaoka's and the Curve fitting methods, respectively. The relations on the Asaoka's and the Curve fitting methods were nearly the same range. 3. The relationships of the field compression index($C_{cfield}$) and virgin compression index($V_{cclab}$) were showed as $C_{cfield}$ = (1.26~1.45)$V_{cclab}$, $C_{cfield}$ = (1.08~1.15) $V_{cclab}$, $C_{cfield}$ = (1.04~1.21)$V_{cclab}$, on the Hyperbolic, Asaoka's and the Curve fitting methods, respectively. 4. The ratio ($C_h/C_v$) of the coefficient of vertical consolidation and the coefficient of horizontal consolidation that is obtained by back-analysis from the settlement data was $C_h$=(0.7~0.9)$C_v$, $C_h$=(0.9~1.5)$C_v$, $C_h$=(2.4~3.0)$C_v$ on the Hyperbolic, Asaoka's and the Curve fitting methods, respectively. 5. It was concluded that the exact consolidation coefficient must be determined after the final settlement is predicted again when the consolidation is finished, because the field consolidation coefficient is decreased as the time allowed to be alone is increased.

• Journal of the Korea Concrete Institute
• /
• v.14 no.1
• /
• pp.126-135
• /
• 2002

Plate bonding technique has been widely used in strengthening of existing concrete structures, although it has often a serious problem of premature falure such as interface separation and rip-off. However, this premature failure problem has not been well explored yet especially in view of local failure mechanism around the interface of plate ends. The purpose of the present study is, therefore, to identify the local failure of strengthened plates and to derive a separation criterion at the interface of plates. To this end, a comprehensive experimental program has been set up. The double lap pull-out tests considering pure shear force and half beam tests considering combined flexure-shear force were performed. The main experimental parameters include plate thickness, adhesive thickness, and plate end arrangement. The strains along the longitudinal direction of steel plates have been measured and the shear stress were calculated from those measures strains. The effects of plate thickness, bonded length, and plate end treatment have been also clarified from the present test results. Nonlinear finite element analysis has been performed and compared with test results. The Interface properties are also modeled to present the separation failure behavior of strengthened members. The cracking patterns as well as maximum failure loads agree well with test data. The relation between maximum shear and normal stresses at the interface has been derived to propose a separation failure criterion of strengthened members. The present study allows more realistic analysis and design of externally strengthened flexural member with steel plates.

• The Korean Society of Law and Medicine
• /
• v.19 no.2
• /
• pp.235-261
• /
• 2018

The Medical law stipulates regulations about the physician's duty to inform to contribute to patient's self-determination. This law was most recently revised on December 20, 2016, and came into effect on June 21, 2017. There has been much controversy about this, and it has been questioned whether or not it will be effective for physicians to comply with the duty to inform. Therefore, this study investigated perceptions of physicians of whether they observed the duty to inform and their legal judgment about that duty, and analyzed how the revision of the medical law may have affected the legal cognition of physician's duty to inform. This study was conducted through an online questionnaire survey involving 109 physicians over 2 weeks from March 29 to April 12, 2018, and 108 of the collected data were used for analysis. The questionnaire was developed by revising and supplementing the previous research (Lee, 2004). It consisted of 41 items, including 26 items related to the experience of and legal judgment about the duty to inform, 6 items related to awareness of revised medical law, and 9 items on general characteristics. The data were analyzed using SAS 9.4 program and descriptive statistics, Chi-square test, Fisher's exact test and Binary logistic regression were performed. The results are as follows. • Out of eight situations, the median number of situations that did not fulfill the duty to inform was 5 (IQR, 4-6). In addition, 12 respondents (11%) answered that they did not fulfill the duty to inform in all eight cases, while only one (1%) responded that he/she performed explanation obligations in all cases. • The median number of the legal judgment score on the duty to inform was 8 out of 13 (IQR, 7-9), and the scores ranged from a minimum of 4 (4 respondents) to a maximum of 11 (3 respondents). • More than half of the respondents (n=26, 52%) were unaware of the revision of the medical law, 27 (25%) were aware of the fact that the medical law had been revised, 20(18%) had a rough knowledge of the contents of the law, and only 5(5%) said they knew the contents of the law in detail. The level of awareness of the revised medical law was statistically significant difference according to respondents' sex (p<.49), age (p<.0001), career (p<.0001), working type (p<.024), and department (p<.049). • There was no statistically significant relationship between the level of awareness of the revised medical law and the level of legal judgment on the duty to inform. These results suggest that efforts to improve the implementation and cognition of physician's duty to inform are needed, and it is difficult to expect a direct positive effect from the legal regulations per se. Considering the distinct characteristics of medical institutions and hierarchical organizational culture of physicians, it is necessary to develop a credible guideline on the duty to inform within the medical system, and to strengthen the education of physicians about their duty to inform and its purpose.

• Korean Journal of Construction Engineering and Management
• /
• v.20 no.4
• /
• pp.114-125
• /
• 2019

Off-Site Construction (OSC) is a new construction method based on factory production. OSC (Off-Site Construction) is a new construction method based on factory production. Researches such as OSC-related design and production standardization, transport methods are actively conducted in the U.S., UK and other parts of the world as this new method has an edge over existing methods in terms of productivity, economy and quality. As the emergence of this new area requires reasonable management, an analysis of the scope of construction project management is required accordingly. Therefore, this research analyzed the study trends and relationships at the CM/PM range's "Operation level" to identify areas of study, relationship between studies and deficiencies in current research. This study carried out a comprehensive literature review of the OSC (CM/PM) research by analyzing 94 papers in Operation level as of September 3, 2018, and the analysis results are as follows. (1) Working stage level researches have been increasing rapidly since 2006. (2) Non-volumetric type is contributing most significantly at work stage level. In the building sector, it has been identified that problems such as residential: living, quality issues, non-residential: economic difficulties, factory: productivity problems have been addressed. (4) The Non-volumetric pre-assembly type dealt with the economic feasibility of residential and non-residential buildings, whereas the modular type was studied in regards to assembly quality. (5) From 2006, project management areas (e.g., quality, human resources, risks) have been expanded. It is expected that this research will help find new areas of research for OSC. If the analysis is carried out to the level of the industrial, corporate and project phases in the future, it is deemed that the overall research flow and area of the OSC industry can be identified.

• The Korean Society of Law and Medicine
• /
• v.22 no.1
• /
• pp.91-124
• /
• 2021

In May 2019, the Ministry of Food and Drug Safety revised the "Pharmaceutical Determination and Adjustment Criteria" with the content of differentially calculating the price of generic drugs according to the registration of the drug substance and meeting the requirements for their own bioequivalence test. According to this revised rule, if their own bioequivalence test is not conducted, even the generic drugs that have already been approved would be lowered in price. I wondered whether this system was introduced with sufficient public legal considerations regarding its legislative purposes and means. Therefore, I reviewed the contents of the revised notice based on whether or not it is valid to determine and adjust the price of generic drugs in terms of the legitimacy of legislative purposes and the proportionality principle after introducing the history and background of the rule. First, I raised a question as to whether the purpose of preventing the overrun of generic drugs is indeed legitimate in terms of the legitimacy of the purpose. In order for the revised notice of "reduction of drug prices when the test requirements are not met," to meet the conformity principle, the premise that it is difficult to recognize safety and effectiveness through consignment (joint) bioequivalence test or that these tests are insufficient in safety and efficacy verification than their own test must be established. Nevertheless, it seems that suffficient review has not been carried out. In order to achieve the purpose of securing safety and effectiveness, the focus should be on 'reinforcement of the standards for bioequivalence test and the management of the bioequivalence test itself' rather than whether it is a their own test or a consignment (joint) test. Third, it is contrary to the necessity and substantiality principle that strict standards are uniformly applied to the products that can be considered to have been sufficiently verified for safety and effectiveness after a considerable period of time has passed after the product approval. In many cases, revised administrative legislations quickly enacted and amended in the state of lack of legal review or consensus, while the regulatory effects resulting from it are quite direct and specific to the regulated person. In this respect, I emphasized that the administrative legislative process also requires substantial review and prior control of the regulatory purposes and means, and that the participation of stakeholders in the legislative procedure is to be strengthened.

• Composites Research
• /
• v.36 no.1
• /
• pp.1-15
• /
• 2023

Demand for energy consumption reduction is increasing according to the development expectations of future mobility. Lightweight structural materials are known as a method to reduce greenhouse gas emissions and improve energy efficiency. In particular, fiber reinforced polymer composite (FRP) is attracting attention as a material that can replace existing metal alloys due to its excellent mechanical properties and light weight. In this paper, industrial applications and research trends of carbon fiber reinforced composites (CFRP, carbon FRP) and self-reinforced composites (SRC) were reviewed based on the reinforcement, polymer matrix, and manufacturing process. In order to overcome the expensive process cost and long manufacturing time of the epoxy resin-based autoclave method, which is mainly used in the aircraft field, mass production of CFRP-applied electric vehicles has been reported using a high-pressure resin transfer molding process including fast-curing epoxy. In addition, thermoplastic resin-based CFRP and interface enhancement methods to solve the recycling issue of carbon fiber composites were reviewed in terms of materials and processes. To form a perfect matrix-reinforcement interface, which is known as the major factor inducing the excellent mechanical properties of FRP, studies on SRC impregnated with the same matrix in polymer fibers have been reported. The physical and mechanical properties of SRC based on various thermoplastic polymers were reviewed in terms of polymer orientation and composite structure. In addition, a copolymer matrix strategy for extending the processing window of highly drawn polypropylene fiber-based SRC was discussed. The application of CFRP and SRC as lightweight structural materials can provide potential options for improving the energy efficiency of future mobility.

• Journal of Life Science
• /
• v.12 no.6
• /
• pp.700-707
• /
• 2002

To study the characteristics of organic and nutrient removal by Bacillus species at high COD concentration of influent, three lab-scale batch reactors(R1, R2, R3), each of which has different substrate composition, were operated. More than 95% of $NH_4^+$-N and $COD_{cr}$, concentrations were removed under an aerobic condition, and their removal efficiencies were found to be 22.6 and 90.5%(R1), 23.9 and 65.8%(R2), 30.2 and 86.4%(R3), respectively. The removal efficiency of $NH_4^+$-N was high when an enough amount of $NO_3^{-}$-N was supplied, and that of $COD_{cr}$. was low when a high concentration of initial $NO_2^{-}$-N was added. The amount of carbon utilized in denitrification was a little. In all reactors,$NO_3^{-}$-N was removed under an anoxic condition, but in the R3 reactor, 10% of $NO_3^{-}$-N could be removed even undo, an aerobic condition. The removal efficiencies of TN and TP were 41.8 and 49.5%(R1), 40.1 and 35.8%(R2), 47.0 and 57.6%(R3), respectively. Alkalinities destructed under an aerobic condition for each reactor were 4.96, 5.41 and 3.93 mg/L (as $CaCO_3$) per each gram of $NH_4^+$-N oxidized, respectively, while 3.06, 3.17 and 2.60 mg/L (as $CaCO_3$) of alkalinities were produced for each gram of ,$NO_3^{-}$-N reduced to $N_2$. The SOUR were found to be 38.5, 52.7 and 42.0 mg $O_2$/g MLSS/hr, which indicated that Bacillus sp. had a higher cell activity than activated sludge. The OLR and sludge production were estimated to be 0.69 and 0.28(Rl), 0.77 and 0.20(R2), 0.61 kg COD/$m^3$/day and 0.25 kg MLSS/kg COD(R3), respectively. From the N-balance, the highest percentage(40.9%) of nitrogen lost to $N_2$ was obtained in the R3 reactor. From all the results, the possibility of aerobic denitrification Bacillus sp. has been shown and the B3 process seemed to have two advantages: a little amount of carbon was required in denitrification and not much amount of alkalinity was destructed under an aerobic condition.