• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1453-1459
• /
• 2011

A roller pinion gear (RPG) system composed of either a pin or a roller and its conjugated cam gear can improve the gear endurance from that of a conventional gear system by reducing the sliding contact while increasing the rolling motion. In this paper, we first proposed the exact cam gear profile and the self-intersection condition obtained when the profile shift coefficient is introduced. Then, we investigated the Hertzian contact stresses and the load stress factors while the varying the shape design parameters to predict the gear surface fatigue life, which is strongly related to the gear noise and vibration at the contact patch. The results show that the pitting life can be extended significantly by increasing the profile shift coefficient.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.4
• /
• pp.225-234
• /
• 2003

Turbo compressors need high speed rotating impeller in structure, high rate gearbox and conventional induction motor. This mechanical system increased moment of inertia and mechanical friction loss. Recently turbo compressor has adopted a super high-speed motor and driver and have made its size smaller and mechanical friction loss at minimum. In this paper, variable super high - speed motor controller, compressor controller and MMI controller are implemented with only one DSP (TMS320VC33) chip for a 150HP, 70,000rpm direct drive turbo compressor. It was required hardware and software integration. The result of integration, Controller hardware became simple and all control software are developed same developing tool. The implements turbo compressor meets the requirements.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.6
• /
• pp.885-890
• /
• 2002

Turbo compressor needs high speed rotation of impeller in structure, high rated gearbox and conventional induction motor. This mechanical system increased the moment of inertia and mechanical friction loss. Resently the study of turbo compressor applied super high speed motor and drive, removing gearbox made its size small and mechanical friction loss minimum. In this study we tried to develope variable super high speed motor controller, compressor controller and MMI controller under one DSP based systems for 1500Hp, 70,000rpm direct drive Turbo compressor. It have to do unitification of each controller"s hardware and software. The result of study is applied to a 150Hp direct turbo compressor and makes it goods.oods.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.1
• /
• pp.45-54
• /
• 2003

Turbo compressor needs high speed rotation of impeller in structure, high rated gearbox and conventional induction motor. This mechanical system increased the moment of inertia and mechanical friction loss. Resently, the study of turbo compressor applied super high speed motor and drive, removing gearbox made its sire small and mechanical friction loss minimum. This paper describes the implementation of the vector control schemes for a variable-speed 131㎾ PMSM(Permanent Magnet Synchronous Motor) drive in super-high speed application.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.8
• /
• pp.1057-1067
• /
• 2010

Vibration and noise analysis as well as strength of gear teeth, gear profile design are considered in order to develop the multi-gear train devices of synchro system for the guns of a warship. A new approach to the critical speed calculation of practical industrial multi-mesh geared system is presented. A transfer matrix model based on Hibner's branch method is developed and the natural properties of the branched rotor system are calculated with using the ${\lambda}$-matrix formulation. A Campbell diagram, in which the excitation sources caused by the mass unbalance of the rotors and the transmitted errors of the gearing are considered, shows that, at theoperating speed, there are not the critical speed.

• Journal of Aerospace System Engineering
• /
• v.14 no.1
• /
• pp.1-7
• /
• 2020

This paper discusses a series of procedures and results for designing the gear part of a fuel transfer pump for an aircraft, developed as an independent technology for the first time in Korea. A gear pump type is selected because the design requirements of the fuel transfer pump are met by a gear pump with a characteristics of less leakage inside than a vane pump with superior overall performance. The gear housing is designed with suitable clearance, considering the outer diameter of the gear, which is the main factor on which the flow can be determined. Additionally, the calculation of the required hydraulic and axial force for the motor to drive the fuel transfer pump was performed.

• Journal of Korea Society of Industrial Information Systems
• /
• v.17 no.7
• /
• pp.35-41
• /
• 2012

To control screen door installed in the subway platform, geared BLDC motors have been being used. However, because of the geared mechanisms, the control profile of the screen door in slow speed is very poor. Moreover, geared mechanism tends to leads system malfunctions and low efficiency. To overcome those problems, in this paper, the techniques of developing hi-efficiency direct drive gearless PMAC motor controller and application example to control the screen door of subway platforms are proposed. The developed system has advantages that; the energy efficiency has been increased by adopting gearless PMAC motor; the system break-down factor has been decreased due to the actuator mechanism has been simplified. In this paper, the screen door control system structure, PMAC motor drive circuit design, implementations of vector control algorithm, and test results are shown.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.380-388
• /
• 2016

Using the magnet gear, it is possible to transmit power without mechanical contact. As the drive shaft in a magnet gear-based speed reducer system is isolated from the drive shaft, the system is a two-inertia resonance system that should cope with an external load with the limited air-gap stiffness. On the other hand, the drive shaft or low-speed side is controlled only by the torque of the drive shaft through an air-gap, and the excessive oscillation or the slip can then be generated because of an abrupt disturbance that is different from the general mechanical gear system. Therefore, the disturbance loaded at the low speed side should be measured or estimated, and considered in the control of the driving shaft. This paper proposes a novel full-state feedback controller with a reduced-order observer for the speed reducer system using a magnet gear with a unified harmonic modulator. The control method was verified by simulation and experiment. To estimate the load at the low speed side, a novel observer was designed, in which the new state variable is introduced and the new state equation is formulated. Using a full-state feedback controller including the observer, the test result against disturbance was compared with two D.O.F PI speed controllers. The pole slip was compensated within relatively a short time, and the simulation result about the estimated variable shows a similar tendency to the test result. The test results showed that the magnet gear-based reducer can be applied to an accurate servo system.

• Journal of the Korean Society for Railway
• /
• v.16 no.1
• /
• pp.26-31
• /
• 2013

The reduction unit is one of the most important components for railway vehicles because the torque of the motor must be transmitted to the wheels of the vehicle by the reduction unit. The faults in the reduction units of high-speed trains are caused by damage such as gear, fatigue. These have serious impacts on safety of the train during operation. To address this development of a system for monitoring, fault diagnosis of the reduction unit is needed to keep the vehicle running safely. Before that can be accomplished, it is most important to understand the vibration characteristics of the reduction unit in a normal state. Vibration diagnosis technology using characteristic-analysis of vibration waveform and frequency is known to be the most effective method for fault diagnosis. In this paper, we analyzed the vibration characteristics of the reduction units two Korean high-speed trains (KTX and KTX II), under normal conditions, by two test methods (driving gear test, full-vehicle test).

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.7
• /
• pp.914-919
• /
• 2004

When the motor is rotating, the torque and rpm are varying as the loads or the driving status connecting through reduction units are changing. On the contrary, one can monitor the changes of the loads or the driving status in the manner of measuring motor torque and rpm. There is a torque measuring method using the strain gauge and bridge circuit. But, because this is the contact method, it has the life time which is dependent on rotating velocity and used time. So this system demands on replacement of some Parts or whole system itself for maintenance. And this system is also relatively big and expensive, requiring preceding annoying process. In this paper, we are going to suppose non-contact method to measure torque and rpm using the Hall effects sensor For this we have made the planetary geared reduction motor with Hall sensors and with the monitoring system. The monitoring system displays the sensing data(torque, rpm) and calculated data( power) and also has the network capability with Bluetooth protocol. Our solution is much more inexpensive ;md simple method to measure torque and rpm than before.