• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.335-342
• /
• 1986

The feasibility of simultaneous measurement of gas-liquid tow-phase flowrate and quality with a sharp-edged orifice has been investigated. Instantaneous pressure drop curves were monitored for various combinations of gas and liquid flowrates in the bubbly flow regime and some statistical properties of the curves were calculated. The time-averaged value of pressure drop increases with increasing gas and liquid flowrate, whereas the mean amplitude and the intensity of fluctuation monotonically increase as void fraction becomes larger in the flow regime. The statistical furctions for the instantaneous curves indicate a consistent pattern throughout the flow regime and the probability density function, which as a single-peaked and symmetrical distribution, is well predicted by the Gaussian distribution function. The results indicate that simultaneous determination of two-phase flowrate and quality may be possible based upon the statistical analysis of instaneous pressure drop curves measured in a sharp-edged orifice.

• Composites Research
• /
• v.33 no.5
• /
• pp.282-287
• /
• 2020

In the present study, a high-strength polyethylene terephthalate (PET) sheet was fabricated through a densification process of low melting PET fiber (LMF) combined PET sheet. During the thermal heat treatment process of the combined LMF, individual PET fiber was connected, which in turn leads to the improvement of the interfacial bonding force between the fibers. Also, the densification of the PET sheet leads to reduce macrospore density and in return could enhance the binding force between the overlapped PET networks. Consequently, the asprepared LMF-PET sheet showed about 410% improved tensile strength and the same elongation compared to before compression. Besides, the enhanced bonding force can prevent the shrinkage of the PET fiber network and exhibited excellent dimensional stability.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.8
• /
• pp.1102-1107
• /
• 1993

Microwave dielectric properties of CaTiO3 and CaTiO3-TiO2 ceramics for the composition range between 40 and 50 mol% CaO in CaO-TiO2 binary system were investigated. CaTiO3 ceramics with50 mol% CaO showed the dielectric constant (e,) of 178, the temperature coefficient of resonant frequency(c,) of+1000 ppm/'c and the qualify factor Q of 2760 (f0=2.7 GHz ). Dielectric constant and temperature coefficient of resonant frequency of ceramics with dual phases of CaTiO3 and TiO2 decreased gradually from those of CaTiO3 as the CaO content decreased. Q value and density were found to have minimum at the composition of 47 mol% CaO. The degradation of Q value and density in dual phase ceramics seems to be caused by the large pores at grain boundaries and/or within grains remained after rapid growth of CaTiO3 grains as TiO2 Phase decreased.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.33.2-33.2
• /
• 2011

CMP (Chemical-Mechanical Planarization) 공정이란 화학적 반응과 기계적 힘을 동시에 이용하여 표면을 평탄화하는 공정으로, 반도체 산업에서 회로의 고집적화와 다층구조를 형성하기 위해 CMP 공정이 도입되었으며 반도체 패턴의 미세화와 다층화에 따라 CMP 공정의 중요성은 더욱 강조되고 있다. CMP 공정은 압력, 속도 등의 공정조건과, 화학적 반응을 유도하는 슬러리, 기계적 힘을 위한 패드 등에 의해 복합적으로 영향을 받는다. CMP 공정에서, 폴리우레탄 패드는 많은 기공들을 포함한 그루브(groove)를 형성하고 있어 웨이퍼와 직접적으로 접촉을 하며 공정 중 유입된 슬러리가 효과적으로 연마를 할 수 있도록 도와주는 역할을 한다. 하지만, 공정이 진행 될수록 그루브는 손상이 되어 제 역할을 하지 못하게 된다. 패드 컨디셔닝이란 컨디셔너가 CMP 공정 중에 지속적으로 패드 표면을 연마하여 패드의 손상된 부분을 제거하고 새로운 표면을 노출시켜 패드의 상태를 일정하게 유지시키는 것을 말한다. 한편, 금속박막의 CMP 공정에 사용되는 슬러리는 금속박막과 산화반응을 하기 위하여 산화제를 포함하는데, 산화제는 금속 컨디셔너 표면을 산화시켜 부식을 야기한다. 컨디셔너의 표면부식은 반도체 수율에 직접적인 영향을 줄 수 있는 scratch 등을 발생시킬 뿐만 아니라, 컨디셔너의 수명도 저하시키게 되므로 이를 방지하기 위한 노력이 매우 중요하다. 본 연구에서는 컨디셔너 표면에 연마 잔여물 흡착을 억제하고, 슬러리와 컨디셔너 표면 간에 일어나는 표면부식을 방지하기 위하여 소수성 자기조립 단분자막(SAM: Self-assembled monolayer)을 증착하여 특성을 평가하였다. SAM은 2가지 전구체(FOTS, Dodecanethiol를 사용하여 Vapor SAM 방법으로 증착하였고, 접촉각 측정을 통하여 단분자막의 증착 여부를 평가하였다. 또한 표면부식 특성은 Potentiodynamic polarization와 Electrochemical Impedance Spectroscopy (EIS) 등의 전기화학 분석법을 사용하여 평가되었다. SAM 표면은 정접촉각 측정기(Phoenix 300, SEO)를 사용하여 $90^{\circ}$ 이상의 소수성 접촉각으로써 증착여부를 확인하였다. 또한, 표면에너지 감소로 인하여 슬러리 내의 연마입자 및 연마잔여물 흡착이 감소하는 것을 확인 하였다. Potentiodynamic polarization과 EIS의 결과 분석으로부터 SAM이 증착된 표면의 부식전위와 부식전류밀도가 감소하며, 임피던스 값이 증가하는 것을 확인하였다. 본 연구에서는 컨디셔너 표면에 SAM을 증착 하였고, CMP 공정 중 발생하는 오염물의 흡착을 감소시킴으로써 CMP 연마 효율을 증가하는 동시에 컨디셔너 금속표면의 부식을 방지함으로써 내구성이 증가될 수 있음을 확인 하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.3
• /
• pp.105-110
• /
• 2015

The fiber-reinforced endodontic posts were prepared using a photocurable resin and a glass fiber. The mechanical property of the posts increased with increasing density of glass fiber and the micro-pores in the post were removed by a vacuum impregnation process. To improve the interfacial adhesion between glass fiber and polymer, silane coupling agent was used. The surface treatment of glass fiber increased the surface wettability of resing on glass fiber and increased the adhesion property with resin, consequently improved the mechanical property of posts.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.159-166
• /
• 1999

The physical properties and microstructural changes with heat-treatment of opacified silica aerogels doped by TiO2 were investigated. Monolithic SiO2-TiO2 aerogels were prepared by supercritical drying (25$0^{\circ}C$, 1250 psig) of wet gel obtained by adding titanium isopropoxide to prehydrolyzed TEOS-isopropanol solutions. The density and the porosity of SiO2-10 mol% TiO2 aerogels were 0.23 g/㎤ and 90%, respectively. During supercritical drying, the linear shrinkage of aerogels increased with increase in the titanium content an TiO2 was transformed to the anatase phase as well as particls agglomerates led to TiO2 clusters of 100~800 nm dispersed homogeneoulsy in the silica matrix. The IR transmittance of opacified silica aerogels was very low in the region of wavelengths below 8 ${\mu}{\textrm}{m}$ compared with pure silica aerogels and SiO2-TiO2 aerogels showed the high thermal stability of microstructures up to $600^{\circ}C$.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.75-75
• /
• 2010

3D 패키징 기술은 전기소자의 소형화, 고용량화, 저전력화, 높은 신뢰성등의 요구와 함께 그 중요성이 대두대고 있다. 이러한 3D 패키징의 연결방법은 와이어 본딩 또는 플립칩등의 기존의 방법에서 TSV(Through Silicon Via)를 이용하여 적층하는 방법이 주목받고 있다. TSV는 기존의 와이어 본딩과 비교하여 고집적도, 빠른 신호전달, 낮은 전력소비 등의 장점을 가지고 있어 많은 연구가 진행되고 있다. TSV의 세부 공정 중 비아필링(Via filling)기술은 I/O수 증가와 미세피치화에 따른 비아(Via) 직경의 감소 및 종횡비(Via Aspect Ratio)증가로 인해 기존 필링 공정으로는 한계가 있다. 기존의 비아 홀(Via hole)에 금속을 필링하기 위한 방법으로 전기도금법이 많이 사용되고 있으나, 전기도금법은 전기도금액 조성, 첨가제의 종류, 전류밀도, 전류모드 등에 따라 결과물에 큰 차이가 발생되어, 최적공정조건의 도출이 어렵다. 또한 20um이하의 비아직경과 높은 종횡비로 인하여 충진시 void형성등의 문제점이 발생하기도 한다. 본 연구에서는 용융솔더와 진공을 이용하여 비아를 필링시켰다. 이 방법은 관통된 비아가 형성된 웨이퍼 양단에 압력차를 주어, 작은 직경을 갖는 비아 홀의 표면장력을 극복하고, 용융상태의 솔더가 관통된 비아 홀 내부로 필링되는 방법이다. 관통 비아홀이 형성 된 웨이퍼 위에 솔더페이스트를 $250^{\circ}C$이상 온도를 가해 용융상태로 만든 후 웨이퍼 하부에 진공을 형성하여 필링하는 방법과 용융솔더를 노즐을 통하여 위쪽으로 유동시켜 그 위에 비아홀이 형성된 웨이퍼를 접촉하고 웨이퍼 상부에 진공을 형성하여 필링하는 방법으로 실험을 각각 실시하였다. 이 때, 웨이퍼 두께는 100um이하이며 홀 직경은 20, 30um, 웨이퍼 상부와 하부의 진공차는 약 0.02~0.08Mpa, 진공 유지시간은 1~3s로 실시하여 최적 조건을 고찰하였다. 각 조건에 따른 필링 후 단면을 전자현미경(FE-SEM)을 통해 관찰하였다. 실험 결과 0.04Mpa 이상에서 1s내의 시간에 모든 비아홀이 기공(Void)없이 완벽하게 필링되는 것을 관찰하였으며 이 결과는 기존의 방법에 비하여 공정시간을 감소시켜 생산성이 대폭 향상 될 수 있는 방법임을 확인하였다.

• Composites Research
• /
• v.27 no.3
• /
• pp.96-102
• /
• 2014

In this study, we fabricated jute fiber reinforced polylactic acid (PLA) composite in the form of sandwich panel structure which includes core foam of chopped jute fiber reinforced PLA and outer skin layer of continuous glass fiber reinforced PLA. Flexural properties of the composite were assessed for different jute fiber weight fractions. Density of the core foam ranged from 0.31 to 0.67 $g/cm^3$ and void content fraction 0.51 to 0.71. The maximum flexural strength was 92.7 MPa at 12.5 wt.% of jute fiber content, and the maximum flexural modulus was 7.58 GPa at 30.0 wt.%. Cost analysis was also conducted. The cost to enhance the flexural strength of the applied structure was estimated to be $0.010USD/m^3/MPa$ for 12.5 wt.% fiber content.

• Journal of Plant Biotechnology
• /
• v.31 no.2
• /
• pp.145-149
• /
• 2004

We investigated the anatomical aspects of vitrification in peace poplar. Comparisons were made with regard to characteristics occurring between hyperhydric and normal shoots in shoot proliferation cultures on MS medium containing 0.2 mg/L BA. Compared with normal plants, hyperhydric plants had thick, curled, and dark green leaves. Hyperhydric stems were thicker and shorter than those of normal stems. When examined under the microscopes, the mesophyll palisade cells of hyperhydric leaves were vacuolated, whereas those of normal leaves contained normal and enriched vacuole with cytoplasm. Generally, the hyperhydric leaves showed poorly developed palisade parenchyma, and revealed irregular and bigger sized intercellular structures in both palisade and spongy parenchyma as well as epidermis cells compare to those of normal leaves. In addition, the hyperhydric leaves had lower stomatal density and bigger sized cell. Vascular tissues of hyperhydic stems were less differentiated because of poorly lignified xylem tissue. The greatly expanded cortical cells and pith appeared to be the main cause of thick stems as compared with normal stems.

• Korean Journal of Food Science and Technology
• /
• v.21 no.6
• /
• pp.780-787
• /
• 1989

The texturization properties of extrudate from isolated soybean protein and rice flour by extrusion cooking were investigated. The addition of up to 30% rice flur to isolated soy proetin could give more tenderness to the texturized extrudate. As the rice flour content increased, die temperature, nitrogen solubility index, and integrity index were decreased slightly with lower chewiness and gumminess. The water content of final extrudate was increased as the addition of rice flour increased, while density was maintained without variation, and rehydration ratio was decreased. The distribution of pressure profile during extrusion were in the range of $15-100kg/cm^3$. As the addition of rice flour increased, scanning electron micrographs demonstrated the gelatinized surface structure of rice starch and the increased air cell size of the testurized extrudate.