• Journal of Energy Engineering
• /
• v.13 no.4
• /
• pp.267-274
• /
• 2004

Theoretical analysis for predicting the heat transport limitations of screen mesh wick and sintered wick heat pipes was performed. The heat pipe diameter was 8mm and water was used for working fluid. For the 250 mesh, each capillary pressures and heat transport limitations, thermal resistances were analyzed according to the operating temperatures, wick thicknesses and inclination angles, based on the effective capillary radius (r$\_$c/), porosity ($\varepsilon$) and permeability (K). The wick capillary limitation was increased as the operating temperature and the wick thickness were increased, and generally the sintered wick showed higher heat transport limitations than that of the screen wick. The thermal resistance of the screen wick was higher than that of the sintered wick and both thermal resistances were linearly increased as the wick thickness was increased.

• Journal of the Korean Chemical Society
• /
• v.43 no.1
• /
• pp.23-29
• /
• 1999

The Al oxide layer formed in 1M $H_2SO_4$ solution and the influence of applied frequency for electrodeposition of Mn on Al oxide layer were characterized using by impedance spectroscopy. Mn compounds were electrodeposited at the base of pores during deposition with applied low frequency voltage. For the Mn deposited oxide layer at 6OHz and 5Hz in 1 g/L $KMnO_4$ solution, in equivalent circuit for interpretation, the resistance ($R_2$) and capacitance ($C_2$) were considered to be due to deposition of Mn on base of pore. The electrochemical behavior of barrier layer and porous oxide layer on Al have been characterized by capacitance ($C_b$) and Young capacitance ($C_Y$) in equivalent circuit model.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1177-1182
• /
• 2003

The porous sensing materials for BaTiO$_3$ gas sensors were fabricated by adding the graphite powders. The crystalline structure and microstructure of the porous BaTiO$_3$-based ceramics were studied. All the sintered bodies showed a tetragonal perovskite structure. The porosity increased with increasing graphite contents. This is mainly due to an enhanced evolution of CO and $CO_2$ gases resulting from the exothermic reactions of graphite and oxygen during the sintering. It was found that the discrepancy in the resistivities measured in air and CO atmospheres at high temperatures (>∼20$0^{\circ}C$) became remarkable with increasing temperature. The sensitivity of CO gas increased with porosity, since the reactions between CO gas and $O_2$$^{[-10]}$ and between CO gas and $O^{[-10]}$ are active due to the formation of many reaction sites. The porous BaTiO$_3$-based ceramics could be promising as a sensing material for CO gas sensors.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.3
• /
• pp.203-207
• /
• 2003

Zinc Air batteries obtain their energy density by utilizing ambient oxygen as the cathode materials. And specific capacity of zinc powder is as high as 820 mAh/g. When Zinc Air battery discharged at low current, then discharge voltage profile has very flat pattern until reach to end of voltage. But, when Zinc Air battery discharged at high current, then discharge voltage and energy becomes very low. So we focused on resistance and porosity of cathode with contents of PTFE. Wf studied on the effects of PTFE on performance of Zinc Air batteries. So we have got optimum contents of PTFE binder.

• Korean Journal of Plant Resources
• /
• v.20 no.5
• /
• pp.437-441
• /
• 2007

The argE gene of E.coli was introduced into #Ilmibyeo# cultivar of rice by Agrobacterium tumefaciens and a large number of transgenic plants were produced. Embryogenic calli were co-cultivated with A. tumefaciens strain AGL1 carrying the plasmid pCAMBIA1300 containing hygromycin resistance(HygR). Transgenic plants showing in vitro resistance to 50mg/L hygromycin were obtained using a selection procedure. Stable integration of argE and HPT genes into chromosomal DNA was proven by southern blot analysis and PCR analysis of genomic isolated from $T_0$ progenies. The fragments of 650 bp(HPT) were detected in transgenic rice lines. The 230 bp(argE) fragments were showed in agarose gel, and detected fragments were matched with size of argE specific primer. The microscopic feature of leaf on scanning electron microscope(SEM) revealed differences between clear and chalky in shape and arrangement of stoma but did not discriminate.

• Applied Chemistry for Engineering
• /
• v.29 no.2
• /
• pp.191-195
• /
• 2018

In this study, the influence of microporous structures of activated carbon fibers (ACFs) on dimethyl methylphosphonate (DMMP) gas sensing properties as a nerve agent simulant was investigated. The pore structure was given to carbon fibers by chemical activation process, and an electrode was fabricated for gas sensors by using these fibers. The PAN based ACF electrode, which is an N-type semiconductor, received electrons from a reducing gas such as DMMP, and then electrical resistance of its electrode finally decreased because of the reduced density of electron holes. The sensitivity of the fabricated DMMP gas sensor increased from 1.7% to 5.1% as the micropore volume increased. It is attributed that as micropores were formed for adsorbing DMMP whose molecular size was 0.57 nm, electron transfer between DMMP and ACF was facilitated. In conclusion, it is considered that the appropriate pore structure control of ACFs plays an important role in fabricating the DMMP gas sensor with a high sensitivity.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.4
• /
• pp.183-188
• /
• 2004

In order to develop polymer electrolyte for lithium/sulfur batteries, highly microporous P(VdF-HFP) membranes were prepared by phase inversion method. Porous structure was controlled by extracting NMP with mixture of deionized water and methanol. Porous structure of the membranes was observed with SEM. Polymer electrolytes were prepared by soaking the porous membranes in 1M $LiCF_3SO_3-TEGDME/EC$. The ionic conductivity of polymer electrolyte was found to be at high as $2\times10^{-3}S/cm$ when the polymer membrane extracted by $80\%$ methanol was used. The microporous polymer electrolyte optimized in this work displayed high ionic conductivity, uniform pore size, low interfacial resistance and stable ionic conductivity with storage time. The ionic conductivity of polymer electrolytes was measured with various lithium salts, and the conductivity showed $3.3\times10^{-3}S/cm$ at room temperature when $LiPF_6$ was used as a lithium salt.

• Clean Technology
• /
• v.25 no.2
• /
• pp.101-106
• /
• 2019

The aim of this study is to investigate the feasibility of an Ni-SA catalyst, which was prepared from nickel, kieselguhr, and alumina, for the hydrogenation of triglyceride in a bench-scale reactor. Ni-SA powders were prepared by precipitating nickel precursors on a silica and alumina support. The powder was reduced in a hydrogen flow, mixed with a saturated palm oil, and then cooled to prepare an Ni-SA catalyst tablet. The sizes of NiO crystals of a commercial Pricat catalyst and the Ni-SA catalyst prepared in this study were $35{\AA}$ and $38{\AA}$, respectively. The pore volume and pore size of the Ni-SA catalyst was much larger than the pore volume and pore size of the Pricat catalyst. In addition, the average particle size of the Ni-SA catalyst was much smaller than that of the Pricat catalyst. The triglyceride hydrogenation reaction was carried out in a semi-batch reactor using catalysts impregnated with oil and molded into tablets. It was found that the Ni-SA catalyst was superior to the commercial Pricat catalyst in triglyceride hydrogenation, which could be ascribed to the raw material and the products being less influenced by the diffusion resistance in the pores of the Ni-SA catalyst. The Ni-SA catalyst prepared in this study has the potential to replace the Pricat catalyst as a catalyst for use in the commercial process for hydrogenation of triglyceride.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.2
• /
• pp.94-99
• /
• 2004

Anode-supported flat tubular solid oxide fuel cell (SOFC) was investigated to increase the cell power density. The anode-supported flat tube was fabricated by extrusion process. The porosity and pore size of Ni/YSZ ($8mol\%$ yttria-stabilized zirconia) cermet anode were $50.6\%\;and\;0.23{\mu}m$, respectively. The Ni particles in the anode were distributed uniformly and connected well to each other particles in the cermet anode. YSZ electrolyte layer and multilayered cathode composed of $LSM(La_{0.85}Sr_{0.15})_{0.9}MnO_3)/YSZ$ composite, LSM, and $LSCF(La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.7}O_3)$ were coated onto the anode substrate by slurry dip coating, subsequently. The anode-supported flat tubular cell showed a performance of $300mW/cm^2 (0.6V,\; 500 mA/cm^2)\;at\;500^{\circ}C$. The electrochemical characteristics of the flat tubular cell were examined by ac impedance method and the humidified fuel enhanced the cell performance. Areal specific resistance of the LSM-coated SUS430 by slurry dipping process as metallic interconnect was $148m{\Omega}cm^2\;at\;750^{\circ}C$ and then decreased to $148m{\Omega}cm^2$ after 450hr. On the other hand, the LSM-coated Fecralloy by slurry dipping process showed a high area specific resistance.

• Current Research on Agriculture and Life Sciences
• /
• v.5
• /
• pp.106-111
• /
• 1987

The susceptibility of 8 chrysanthemum varieties to Apelenchoides ritzemabosi, Shuhonothikara and Sagakiku were resistant by 11.7% and 14.5% each infested leaf, Sinrokusiogio, Dangonanako and Sintoa were susceptible as above 50%, Gold wave and Tenju were modertae by 24 to 26%. Percentage of infested leaf was positively correlated with the number of epidermal hair but not with leaf area, leaf thickness, stomatal size, number of stomata and length of epidermal hair. In effect of watering method, Polyethylene film cover plot was lowest by 9.4%, next conventional watering plot by 50%, Conventional watering and spray plot was the highest by 62%. The infested leaf rate was closely related with a number of rainy days than the amount of rainfall. Effect of chemical soil treatment, Temik showed the lowest infested leaf rate by 5%. There was no significant difference between the chemicals except Temik, but these are markedly effective in compare to control.