• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.6
• /
• pp.238-242
• /
• 2016

The effect of the alkali, alkali earth metal elements on selective catalytic reduction(SCR) catalyst deactivation behavior were investigated in terms of microstructure, surface area, pore volume and De-NOx test. Poisoned SCR catalyst were manufactured by injection of $K_2CO_3$, $Na_2CO_3$, $Ca(CH_3COO)_2{\cdot}H_2O$, $C_4H_6MgO_4{\cdot}4H_2O$, $H_3PO_4$ solutions in the new SCR catalyst at $350^{\circ}C$ for 6 hours. New and poisoned catalysts surface were similar. But specific surface area, pore volume decrease from Na, Mg, K, Ca, P compared to new SCR catalyst. Especially, Na poisoned catalyst surface area and pore size extremely decreased by $10.20m^2/g$, $0.061cm^2/g$. De-NOx test results of new and poisoned catalysts at $150{\sim}450^{\circ}C$ indicated that alkali metal (K, Na) poisoned SCR catalysts have the lowest De-NOx efficiency, alkali earth metal poisoned SCR catalysts (Ca, Mg) De-NOx efficiency are higher than alkali metal poisoned SCR catalysts. P poisoned SCR catalyst De-NOx efficiency is similar new SCR catalyst. It were considered that physical deactivation of SCR catalyst was affected by SCR catalyst surface area and pore volume change.

• Applied Chemistry for Engineering
• /
• v.29 no.4
• /
• pp.432-439
• /
• 2018

Metal catalysts such as Fe, Co, Mn, and Pd supported on the activated carbon (AC) were prepared to improve functional groups for the chemical adsorption and catalytic ozonation. Following ascending orders of the phenol decomposition rate, dissolved ozone decomposition ratio and TOC (total organic carbon) removal from experimental results of advanced oxidation process (AOP) were observed: Fe-AC < AC < Co-AC < Mn-AC < Pd-AC. BET analysis results showed that the physical properties of the metal impregnated activated carbon had no effect on the catalytic ozonation, and the catalytic effect was dependent on the kind of impregnated metal. The ratio of the formed concentration of OH radical to that of ozone (RCT) was measured by using the decomposition outcome of p-chlorobenzoic acid, a probe compound that reacts rapidly with OH radical but slowly with ozone. The measured values of RCT were $5.48{\times}10^{-9}$ and $1.47{\times}10^{-8}$ for the ozone alone and activated carbon processes, respectively, and $2.13{\times}10^{-9}$, $1.51{\times}10^{-8}$, $4.77{\times}10^{-8}$, and $5.58{\times}10^{-8}$ for Fe-AC, Co-AC, Mn-AC, and Pd-AC processes, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.219-219
• /
• 2016

유기발광소자는 저전력, 빠른 응답속도, 고휘도 및 자체발광 등의 장점들 때문에 고체 광원과 플렉서블 디스플레이로 연구가 진행되고 있다. 유기발광소자는 유기 발광층을 인광물질로 사용 함으로서 100 % 내부양자 효율을 이루고 있지만 공기와 유리기판의 계면과 유리 기판과 ITO 계면에서 발생하는 내부 전반사 효과와 유기물과 ITO 기판 사이에서 발생하는 웨이브 가이드 효과 등으로 인해 발광량의 약 20 %만을 외부로 추출 할 수 있다. 따라서 유기발광소자의 광 추출 효과를 증가시키기 위해서 소자외부에 아웃커플링 필름 또는 마이크로렌즈 어레이 필름을 부착시키는 방법, 금속 나노 입자를 유기발광소자 내에 삽입하여 표면 플라즈몬 효과로 인한 광추출 효율을 높이는 방법 등이 제시되고 있다. 본 연구에서는 Au-ZnO 나노복합체를 간단한 졸겔법을 이용하여 양극 버퍼층으로 사용하여 그에 따른 계면, 전기적 및 광학적 특성을 분석하였다. Au-ZnO 나노복합체를 포함한 tris(8-hydroxyquinolinato) aluminium (Alq3) 발광층에서 ZnO를 포함한 Alq3 발광층보다 엑시톤 수명이 빠르게 감소하는 것을 시간 관련 단광자 계산(Time-Correlated Single Photon Counting) 측정을 통해서 알 수 있었다. 이러한 결과는 Au 금속 나노입자의 플라즈몬 흡수 파장과 Alq3 발광층에서 생성되는 발광 파장이 겹쳐서 효과적인 공명 에너지 전달효과로 인해 Alq3 발광층의 발광성질이 향상된 것을 의미한다. Au-ZnO 나노복합체와 ZnO 나노입자를 가지는 유기발광소자의 전류 효율은 50 mA/cm2 에서 각각 2.27와 1.83 cd/A 가지는 것으로 확인 되었다. 또한 Au-ZnO 나노복합체와 ZnO 나노입자를 사용한 유기발광소자의 전압-전류밀도가 유사한 것을 확인 할 수 있는데 이는 Au 금속 나노입자가 ZnO 나노입자의 정공 주입능력을 저하시키지 않는 것을 의미한다.

• Polymer(Korea)
• /
• v.25 no.5
• /
• pp.642-648
• /
• 2001

An attempt was made to synthesize an ammonia adsorbent by the photo-induced grafting of styrene (St) onto polypropylene (PP) nonwoven using benzoin ethyl ether (BEE) as a photosensitizer with urea and trimethylol propane triacrylate in methanol medium. As styrene concentration was increased, the graft yield was increased. It was also found that the graft yield increased with reaction time. The polypropylene grafted with styrene (PP-g-St) was sulfonated by chlorosulfonic acid in dichloroethane and complexed with several metal ion, such as $cO^{+2}$, $nI^{+2}$, $cU^{+2}$, $Zn^{+2}$. The amount of ammonia gas adsorbed by these sample was dependent on the degree of sulfonation, adsorption time, and ammonia gas pressure. The adsorption capacity of ammonia gas by the sulfonated PP-g-St(SPP-g-St) nonwoven with 4. 25 mmol $H^+$/g was 6.61 mmol/g. Metal ion complexed SPP-g-St nonwovens had higher adsorption capacity than SPP-g-St nonwoven and the $Co^{+2}$ complexed SPP-g-St showed 9.90 mmol $NH_3$/g, which was much higher than that of active carbon or silica gel.

• Analytical Science and Technology
• /
• v.15 no.1
• /
• pp.7-14
• /
• 2002

Laser ablation ion trap mass spectrometry (LAITMS) was developed for the analysis of metal and ceramic samples. For this study, XeCl excimer laser (308 nm) was used for ablating the samples and ITMS was used as a detector. Samples were introduced from outside of a ring electrode and this way of sample introduction was very effective for solid samples when laser ablation was employed. Helium gas was used as a buffer gas, and its effect on sensitivity and some parameters (buffer gas pressure, ion storage time, and cut-off RF voltage) were studied. The optimized conditions were $1{\times}10^{-4}$ Torr of buffer gas pressure, 100 ms of ion storage time and $1150V_{p-p}$ of cut-off RF voltage. From that results, copper (Cu) and molybdenum (Mo) metals were tested with LAITMS and the mass spectra of these pure metals were compared with the natural abundance of isotope ratio. We also examined ceramic samples ($Al_2O_3$, $ZrO_2$) and represented the result of elemental analysis.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.903-906
• /
• 2008

To analyze the growth of SOB (Thiobacillus novellus) and biochemical corrosion of concrete, simulation test method and device were developed. And two types of simulation tests were conducted according to a transplant method and a concentration of H2SO4. As a result, the SOB growth in distinct manners and antibiosis of specimen were observed. In the case of the specimens indirectly transplanted with SOB through culture solution submersion at a hydrogen sulfide level of 120ppm, the rapid activation of SOB and the resulting sulfuric acid production were observed. However, SOB were shown to grow rapidly and then die out in a relative short period of time. Meanwhile, in the case of the specimens directly transplanted with SOB at a hydrogen sulfide level of 50ppm, the long-term growth of SOB was possible, but the production of sulfuric acid by SOB did not progress. In the case of the antibiotic metal-mixed specimens, SOB with destroyed cell membranes and internal organizations were observed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.3
• /
• pp.273-277
• /
• 2005

We prepared $0.25\~l.5um$ poly silicon gate array test group with $SiO_2$ spacers in order to employ NiCo composite salicide process from 15nm Ni/15nm Co/poly structure. We investigate the residual metal shape evolution by varying the rapid thermal silicide anneal temperature from $700^{\circ}C\;to\;1100^{\circ}C$. We observed the residual metals agglomerated into maze type and line type on $SiO_2$ field and silicide gate, respectively as temperature increased. We propose that lower silicide temperature would be favorable in newly proposed NiCo salicide in order to lessen the agglomeration causing the leakage and scum formation.

• Clean Technology
• /
• v.20 no.1
• /
• pp.7-12
• /
• 2014

Hydrogenolysis of glycerol to propylene glycol was performed over binary and ternary metal oxide catalysts. The conversion of glycerol and selectivity to propylene glycol were increased on Cu/Zn and Cu/Cr mixed oxides compared to pure CuO and ZnO oxides. The addition of alumina into Cu/Zn mixed oxide very highly increased the conversion of glycerol and selectivity to propylene glycol. The conversion of glycerol was increased with increasing the reaction temperature but the selectivity to propylene glycol was shown to have maximum value at $200^{\circ}C$ and then decreased at $250^{\circ}C$. The conversion of glycerol and selectivity to propylene glycol were decreased with increasing the glycerol concentration.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.1
• /
• pp.35-41
• /
• 2002

Flip-chip interconnection that uses solder bump is an essential technology to improve the performance of micro-electronics which require higher working speed, higher density, and smaller size. In this paper, the shear strength of Cr/Cr-Cu/Cu UBM structure of the high-melting solder bump and that of low-melting solder bump after aging is evaluated. Observe intermetallic compound and bump joint condition at the interface between solder and UBM by SEM and TEM. And analyze the shear load concentrated to bump applying finite element analysis. As a result of experiment, the maximum shear strength of Sn-97wt%Pb which was treated 900 hrs aging has been decreased as 25% and Sn-37wt%Pb sample has been decreased as 20%. By the aging process, the growth of $Cu_6/Sn_5$ and $Cu_3Sn$ is ascertained. And the tendency of crack path movement that is interior of a solder to intermetallic compound interface is found.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.65-65
• /
• 2009

철강 재료의 GMA 용접 시, 보호가스로 $CO_2$ 가스를 사용하면 가격이 저렴하고 용입이 깊다는 장점이 있어 국내에서 광범위하게 사용되어 왔다. 그러나 일반적으로 활성가스인 $CO_2$를 사용한 GMA용접은 아크가 불안정하고 스패터가 많이 발생한다는 단점이 있어 아크 안정성 개선의 필요성이 부각되었다. 거기다 용접 자동화 및 용접 품질의 고급화 추세로 아크 안정성이 $CO_2$용접에서 점점 중요해지면서, 아크 안정화 및 스패터 저감을 위한 연구가 활발히 진행되어 왔다. 본 연구에서는 GMA 용접 재료인 solid wire의 표면에 이온화 에너지가 낮은 금속인 인듐(In)을 전해 도금하여 중전류의 $CO_2$ 용접에 적용하였다. 고속 촬영과 아크 모니터링 분석을 통하여 금속 이행 모드 및 아크 안정화에 미치는 영향에 관하여 연구하였다. 동일 전압, 전류 조건에서 도금 두께를 달리하여 용접을 실시, 도금 두께에 따른 아크 안정성의 경향을 분석하였다. 그 결과 도금 두께가 두꺼워짐에 따라 아크가 넓어지는 것을 확인하였으며, 이는 아크 내에 이온화도가 높은 인듐 이온이 다량 포함됨으로써 이온의 양이 증가하기 때문인 것으로 생각된다. 또한 도금 두께가 일정 이상이 되면, 이행 모드가 용적의 아래에서 아크가 발생하는 반발 이행 모드에서 용적의 윗부분에서 아크가 발생하는 입상 용적 이행 모드로 바뀌었으며, 이때 단락 수가 현저히 줄어들어 아크가 안정해졌다. 이에 따라 인듐 도금 와이어는 기존보다 낮은 전류 영역에서도 안정적인 아크와 금속 이행 모드를 가지게 됨을 확인하였다.