• Journal of the Korean Magnetics Society
• /
• v.17 no.5
• /
• pp.194-197
• /
• 2007

Understanding the spin polarization (P) has been an ongoing research challenge. The $Co_{1-x}Mn_x$ (x=0.27, 1) and $Co_{1-x}Fe_x$ (x=0, 0.5, 1) films were prepared using UHV-MBE system. For these films, the magnetic properties and spin polarization were investigated using SQUID and Meservey-Tedrow technique, respectively. Although measured P is uncorrelated to the bulk magnetic moment (M) in Co-Fe and Ni-Fe alloy films, it correlates with M in some alloys such as Co-Mn and Ni-Cu. The results can be understood by the tunneling currents made up of the hybridized sp-d electrons near the Fermi-energy level. Our work shows the feasibility to tailor new materials with large P values.

• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.85-101
• /
• 1994

Effect of Cr, Cu and Ni metal powders addition on the alloyed layer of aluminum alloy (AC2B) has been investigated with the plasma transferred arc (PTA) overlaying process. The overlaying conditions were 125-200A in plasma arc current, 150mm/min in process speed and 5-20g/min in powder feeding rate. Main results obtained are summarized as follows: 1) It was made clear that formation of thick surface alloyed layer on aluminum alloy is possible by PTA overlaying process. 2) The range of optimum alloying conditions were much wider in case of Cu and Ni powder additions than the case of Cr powder addition judging from the surface appearance and the bead macrostructure. 3) Alloyed layer with Cu showed almost the homogeneous microstructure through the whole layer by eutectic reaction. alloyed layers with Cr and Ni showed needle-like and agglomerated microstructures, the structure of which has compound layer in upper zone of bead by peritectic and eutectic-peritectic reactions, respectively. 4) Microconstituents of the alloyed layer were analyzed as A1+CrA $l_{7}$ eutectics, C $r_{2}$al sub 11/, CrA $l_{4}$, C $r_{4}$A $l_{9}$ and C $r_{5}$A $l_{*}$ 8/ for Cr addition, Al+CuA $l_{2}$(.theta.) eutectics and .theta. for Cu addition, and Al+NiA $l_{3}$ eutectics. NiA $l_{3}$, N $i_{2}$A $l_{3}$ and NiAl for Ni addition. 5) Concerning defect of the alloyed layer, many blow holes were seen in Cr and Ni additions although there was lesser in Cu addition. Residual gas contents in blow hole for Cu and Ni alloyed layer were confirmed as mainly $H_{2}$ and a littie of $N_{2}$ Cracking was observed in compound zone of the alloyed layer in case of Cr and Ni addition but not in Cu alloyed layer.r.r.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.197-197
• /
• 2011

고온 스퍼터 공정과 구리 리플로우 공정을 통해 다공성 니켈 지지체에 팔라듐-구리-니켈 삼원계 합금 수소 분리막을 제조하였다. 그러나 스퍼터와 같은 물리적 증착법은 주로 주상정 형태로 증착되기 때문에 다공성 니켈 지지체 표면의 수마이크론 내외의 기공이 존재할 경우 다공성 니켈 지지체에 기인한 많은 기공들 때문에 스퍼터 증착에 영향을 주어 수소 분리막 표면에 기공들이 존재하게 된다. 이를 방지하고 균일한 증착이 이루어지도록 다공성 지지체 표면의 전처리 공정이 필요하다. 본 연구에서는 스퍼터 코팅에 의한 균일한 팔라듐 금속층 형성하고 표면에 미세기공이 없는 수소 분리막을 제조하기 위해 다공성 니켈 지지체를 니켈도금, 알루미나 분말 주입 및 미세연마 전처리 공정을 통하여 다공성 니켈 지지체의 표면기공들을 매립하여 치밀한 팔라듐 합금 층을 형성하였다. 전처리를 하지 않은 다공성 니켈 지지체는 팔라듐 및 구리의 고온 스퍼터 증착 및 구리 리플로우 공정에 의해 표면 기공을 막을 수가 없었고 수소분리기능이 없어 수소 분리막으로 역할을 하지 못했다. Al2O3 분말 주입 전처리 공정을 한 다공성 니켈 지지체에 팔라듐 및 구리 고온 스퍼터 증착과 구리 리플로우 공정을 이용하여 제조된 수소 분리막은 다공성 니켈 지지체에 기인한 기공을 메우기 위해서 팔라듐 합금 층이 두꺼워지는 어려움이 있었다. 니켈도금 전처리 공정을 한 다공성 니켈 지지체에 형성한 수소 분리막은 우수한 선택도를 가졌으나 도금 전처리에 사용된 $2{\mu}m$ 두께의 니켈층이 수소의 확산을 방해하는 저항막 역할을 하여 수소 투과도가 3.96 $ml{\cdot}cm-2{\cdot}min-1{\cdot}atm-1$으로 낮게 나타났다. 미세연마 전처리 공정을 한 다공성 니켈 지지체에 형성한 수소 분리막 역시 우수한 수소 선택도를 가졌으며, 수소의 확산을 방해하는 저항막이 존재하지 않아 13.2 $ml{\cdot}cm-2{\cdot}min-1{\cdot}atm-1$의 우수한 수소 투과도를 나타내었다.

• Journal of the Korean Magnetics Society
• /
• v.17 no.6
• /
• pp.226-231
• /
• 2007

High frequency loss property of nanocrystalline amorphous ribbon with a high resistivity insulation layer of $TiO_2$ and $SiO_2$ was studied. The insulation layer was fabricated by sol-gel method using dip-coating. The optimum composition ratio of metal alkoxide and slurry for fabrication of insulation layer was established and insulation layer with high adhesion was coated on the nanocrystalline amorphous ribbon. Frequency loss of magnetic core material manufactured on nanocrystalline amorphous ribbon with the surface insulation layer decreased over 40 % compared with that of magnetic core material without surface insulation layer. The insertion loss of an inductive coupler, which was prepared by using magnetic core material coated insulation layer, decreased due to reduction of frequency loss for magnetic core material and insertion loss decreased in proportion to frequency.

• Journal of the Korean Magnetics Society
• /
• v.8 no.5
• /
• pp.255-260
• /
• 1998

Fabrication condition and magnetic properties of ultrathin Co-based amorphous alloy have been investigated. When the ejection gas pressure was lower than 0.05 kgf/$\textrm{cm}^2$ at the roll speed of 55 m/s, ultrathin ribbons with the thickness less than 10 ${\mu}{\textrm}{m}$ were successfully obtained. The ribbon thickness decreased linearly with the decrease in ejection pressure. Moreover the significant decrease in ribbon width was accompanied with the decrease of thickness in the range of ejection pressure to form an ultrathin ribbon. This behavior was attributed to the decrease of effective ejection pressure in the both end-sides of rectangular nozzle due to the larger friction between molten metal and nozzle wall. The effective permeability at low frequency (1 kHz) decreased largely with the decrease in ribbon thickness, while the coercive force increased with the thickness decrease. It was considered that these behaviors were due to the enhancement of surface effect leading to the suppression of wall motion. However effective permeability at high frequency (1 MHz) increased with the decrease in ribbon thickness, and this was ascribed to the easier magnetization rotation owing to the reduction of eddy current.

• Membrane Journal
• /
• v.22 no.1
• /
• pp.1-7
• /
• 2012

We make a studyof the hydrogen permeability and chemical stability of $Nb_{56}Ti_{23}Ni_{21}$ metal alloy membrane. For this purpose, we produced the $Nb_{56}Ti_{23}Ni_{21}$ membrane which has 10 mm diameter and 0.5 mm thick, and experiment the hydrogen transport properties under two kinds of feed gas ($H_2$ 100%; $H_2$ 60% + $CO_2$ 40%) at $450^{\circ}C$C with variation of absolute pressure.The maximum hydrogen permeation flux was $5.58mL/min/cm^2$ in the absolute pressure 3 bar under pure hydrogen. And each case of feed gases about gas composition, the permeation fluxes were satisfied with Sievert's law, and the hydrogen permeation flux decreased with decrease of hydrogen partial pressure irrespective of temperature and pressure. After permeation test, we experiment the stability and durability of $Nb_{56}Ti_{23}Ni_{21}$ alloy membrane for carbon dioxide by XRD analysis.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.8
• /
• pp.661-669
• /
• 2021

A mechanical stiffener has been mainly applied on a PCB to secure fatigue life of a solder joint of an electronic components in spaceborne electronics by minimizing bending displacement of the PCB. However, it causes an increase of mass and volume of the electronics. The high damping PCB implemented by multi-layered viscoelastic tapes of a previous research was effective for assuring the fatigue life of the solder joint, but it also has a limitation to decrease accommodation efficiency for the components on the PCB. In this study, we proposed high damping PCB with a multi-layered superelastic shape memory alloy stiffener for spatialminimized, light-weighted, high-integrated structure design of the electronics. To investigate the basic characteristics of the proposed PCB, a static load test, a free vibration test were performed. Then, the high damping characteristic and the design effectiveness of the PCB were validated through a random vibration test.

• Korean Journal of Materials Research
• /
• v.11 no.8
• /
• pp.629-635
• /
• 2001

To improve the ductility of $A1_3Hf$ intermetallics, which are the potential high temperature structural materials, the mechanical alloying behavior. the effect of Cu addition on the $Ll_2$ phase formation and the behavior of vacuum hot-pressed consolidation were investigated. During the mechanical alloying by SPEX mill, the $Ll_2 A1_3Hf$ intermetallics with the grain size of 7~8nm was formed after 6 hours of milling in Al-25at.%Hf system. The $Ll_2$ Phase of Al_3Hf$ intermetallics with the addition of 12.5at.%Cu, similar to that of the binary Al-25at.% Hf, was formed, but the milling time necessary for the formationof the $Ll_2$ phase was delayed form 6 hours to 10 hours. The lattice parameter of ternary $Ll_2(Al+Cu)_3Hf$ intermetallics decreased with the increase of Cu content. The onset temperature of $Ll_2$ to $D0_{23}$ phase in $Al_3Hf$ intermetallics was around 38$0^{\circ}C$, the temperature upon completion varied from 48$0^{\circ}C$ to 5$50^{\circ}C$ as the annealing time. The onset temperature of $Ll_2$ to $D0_{23}$ phase transformation in $(Al+ Cu)_3Hf$ intermetallics increased with the amount of Cu and the highest onset temperature of $700^{\circ}C$ was achieved by the Cu addition of 10at.%. The relative density increased from 89% to 90% with the Cu addition of 10at.% in $Al_3Hf$ intermetallics hot-pressed in vacuum under 750MPa at 40$0^{\circ}C$ for 3 hours. The relative density of 92.5% was achieved without the phase transformation and the grain growth as the consolidation temperature increased from 40$0^{\circ}C$ to 50$0^{\circ}C$ in $(Al+Cu)_3Hf$ intermetallics hot-pressed in vacuum under 750MPa for 3 hours.

• The korean journal of orthodontics
• /
• v.40 no.1
• /
• pp.27-33
• /
• 2010

Objective: The need to bond orthodontic brackets onto various alloys has increased because of the increasing demand for adult orthodontic treatment. This study tried to evaluate the shear bond strength between gold alloy and metal bracket using light emitting diode (LED) light curing after metal primer and silicoating surface conditioning. Methods: Half of the type III gold alloy plates were treated with sandblasting with aluminum oxide and metal primer containing 4-META. the other half were treated with silica and silane. Metal brackets were bonded with Transbond XT light curing adhesive on these plates and shear bond strength were evaluated 1 hour, 6 hours, and 24 hours later. The differences of shear bond strength between groups were evaluated with two-way ANOVA. Results: The results showed higher bond strength in the silicoating group and a tendency of bond strength increase over time. Conclusions: When using LED curing lights for metal bracket bonding to alloy surfaces, long curing time and silicoating can produce a reliable bonding strength.

• Journal of Conservation Science
• /
• v.32 no.1
• /
• pp.33-42
• /
• 2016

Modern cultural heritage were made with various materials. But there are no certain analysis for modern cultural heritage. Analysis on rickshaw from National Museum of Korean Contemporary History were carried out using P-XRF, species identification, paint film analysis, FT-IR and microscope observation. As a result Copper and Zinc were measured in metal parts. Nickel alloys were first used in the modern era for rickshaw. Wooden parts, Oak(Quercus spp.), bamboo(Phyllostachys spp.) and Hinoki cypress(Chamaecyparis spp.) were identified. Outer films were painted by 5 layers and inner films were painted by 3 layers. More simple painting process were performed on the inner part. Cotton and wool were identified by FT-IR. Also, cowhide were identified. Authenticity conservation and restoration could be carried out with the results.