• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1994.05a
• /
• pp.9-14
• /
• 1994

알카리금속염 (K$_2$CO$_3$, $K_2$SO$_4$). 알카리 토금속염 (Ba(NO$_3$)$_2$), 철족금속염(Ni(NO$_3$)$_2$, FeSO$_4$) 으로 이루어진 여러가지 혼합물들이 반응온도 700~85$0^{\circ}C$ 하의 촤-수증기 가스화반응에서 나타내는 촉매활성을 열천칭 반응기를 사용하여 측정하였다. 비촉매 가스화반응에서 초기반응성은 수증기 분압에 비례하였다. 촉매 가스화반응에서 단일염 촉매의 경우 $K_2$CO$_3$ 가 가장 큰 활성을 나타내었으며, 다른 염들은 낮은 활성을 보였다. 혼합염의 경우 $K_2$SO$_4$에 철족염을 부가함에 따라 반응속도가 향상되었으며, $K_2$SO$_4$+Ni(NO$_3$)$_2$가 가장 큰 촉매활성을 나타내었다. $K_2$SO$_4$와 Ni(NO$_3$)$_2$ 의 촉매 활성은 담지량에 따라 증가하며, 석탄의 등급에 따라 감소하였다. $K_2$SO$_4$와 Ni(NO$_3$)$_2$의 혼합비는 같은 몰비로 혼합하였을때 가장 큰 활성을 나타내었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.86.2-86.2
• /
• 2011

저온형 연료전지인 직접 메탄올 연료전지(Direct Methanol Fuel Cells, DMFC)는 친환경적인 발전 시스템, 높은 에너지 효율의 장점 때문에 주목을 받고 있으나 연료극의 촉매로 사용되는 금속은 고가의 귀금속인 Pt와 Ru가 요구되어 제조비용이 비싸기 때문에 촉매의 양을 줄이고, 반응 도중 생성되는 CO에 의한 촉매의 피독 문제 등 해결하여야 할 점이 산적해 있어 연료전지 중 촉매의 활성을 높이는 연구들이 활발히 이루어지고 있다. 종래의 MEA의 촉매층 제조공정은 우선 환원석출법에 의해 Pt-Ru/C를 합성하고 Nafion 용액에 혼합하여 Pt-Ru/C 슬러리를 제조한다. 이 방법에서는 carbon sheet에 spray 방법으로 Pt-Ru/C 촉매층이 만들어지기 때문에, Pt-Ru 촉매가 Nafion에 의해 부분적으로 매몰되어 촉매의 전기화학적 활성이 떨어지는 문제점이 있다. 이를 해결하는 방안으로 펄스전류를 이용하여 Pt-Ru 합금입자를 carbon sheet에 전기화학적으로 담지 시켜 Nafion에 매몰되는 것을 방지하는 펄스전해법 연구가 진행되고 있다. 그러나 촉매의 입자크기가 일반적으로 50~70 nm 이상으 크기 때문에 촉매의 낮은 활성이 문제점으로 야기되고 있다. 본 연구에서는 Pt-Ru/C 촉매층 제조 문제점을 해결하고, 촉매의 전기화학적 활성을 증가시키기 위해서 2~4 nm Pt-Ru 콜로이드를 전해액으로 사용하고, 전기영동법을 이용하여 Pt-Ru 나노 입자를 carbon sheet($1{\times}1cm^2$) 에 담지 시켰다. 전기영동법에서 균일한 Pt-Ru 촉매층의 제조를 위해 전류인가 방법으로는 펄스전류를 사용하였고, 실험변수로는 전해액 pH, duty cycle, 담지시간을 선정하였다. 합성된 Pt-Ru 콜로이드를 TEM분석으로 나노입자의 크기와 분산성 분석하였고, 콜로이드 나노입자의 표면전하 상태를 분석하기 위해 zeta-potential을 분석하였다. Pt-Ru/C의 촉매의 전기화학적 활성을 분석하기 위하여 0.5 M H_2SO_4$ 와 1 M $CH_3OH$ 혼합용액에 CV(Cyclic Voltammetry)실시하였고, carbon sheet 전극 상 Pt-Ru의 분산성 확인을 위하여 FE-SEM분석을 수행하였다.

• Clean Technology
• /
• v.18 no.1
• /
• pp.83-88
• /
• 2012

In order to improve the stability of ${\gamma}-Al_2O_3$ on hydrolysis of $SF_6$, the catalytic promoters were investigated in this study. The crystal phase of ${\gamma}-Al_2O_3$ is transformed to their ${\alpha}$-phase during hydrolysis of $SF_6$. Various metal oxides were applied as the promoter material that is Ga, Mg, and Zn and the promoter of 1, 5, and 10 wt% was impregnated over ${\gamma}-Al_2O_3$ by the impregnation method. Specially, it were confirmed in the catalytic activity tests and XRD analysis that ZnO/${\gamma}-Al_2O_3$ catalyst had the high activity for decomposition of $SF_6$ by catalytic hydrolysis and the crystal phase of ZnO promoted ${\gamma}-Al_2O_3$ was not transformed. From these results, it could be known that the stability of ${\gamma}-Al_2O_3$ is enhanced with the catalytic promotion of ZnO impregnated over the surface of catalyst.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2011.10a
• /
• pp.511-512
• /
• 2011

• Applied Chemistry for Engineering
• /
• v.3 no.1
• /
• pp.24-34
• /
• 1992

Recent studies dealing with the fundamental understanding and applications of bimetallic catalysts are discussed. Bimetallic catalysts have had a major industrial impact, specifically for the reforming of petroleum naphtha, for the hydrogen reduction of carbon monoxide, and for the three way catalytic converter system. The action of the bimetallic catalysts in these reactions may be interpreted in terms of ensembles, electronic influences and surface structure. Various combinations of metal pairs have been considered in order to evaluate the role played by the added metals. For catalyst selectivity control, the possibility of surface enrichment of one element has been recognised. More generally, the influence of preparative variables on the formation of supported catalysts has been clarified, In particular by temperature programmed reduction (TPR). Information on the structure of bimetallic catalysts has been obtained with chemical probes, such as chemisorption and reaction rate measurement and physical probes, such as extended X-ray absorption fine structure (EXAFS), scanning transmission electron microscopy (STEM) and Xe-NMR.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.321-330
• /
• 2005

In 1990's the Korean polyolefin industry boomed up through the development of magnificient polymerization catalysts. To understand the general situation of polymerization catalyst R & D, the various experimental results had been summarized for the investigation of not only the supported Ziegler-Natta catalyst used presently in polyolefin industry but also the metallocene catalysts applied for the preparation of special grade of polyolefin. In addition, it had been shown that the new polymeric materials were prepared by new developed catalyst, and the polymer in-situ nanocomposites could be obtained with the application of catalyst heterogenization procedures.

• Applied Chemistry for Engineering
• /
• v.28 no.1
• /
• pp.64-72
• /
• 2017

A series of Pt-based ${\gamma}-Al_2O_3$ catalysts promoted with several alkali and alkaline earth metals were prepared by a wet impregnation method. We confirmed that the addition of Na to $Pt/{\gamma}-Al_2O_3$ could cause a change in the oxidation state of Pt through an electronegative gap between Pt and Na atom, and increase the ratio of the metallic Pt. The metallic Pt species made by adding an optimum Na content improved the adsorption of NO species on the catalyst surface and restrained the oxidation of $CH_4$ to $CO_2$. When molar ratio of Na/Pt was 4.0, the highest catalytic activity could be obtained.

• Applied Chemistry for Engineering
• /
• v.1 no.1
• /
• pp.100-105
• /
• 1990

Small amounts of potassium were added to the titania - supported cobalt catalysts in order to produce higher and olefinic hydrocarbons in CO hydrogenation. Titania and potassium played important roles not only for the enhancement of the production of higher and olefinic hydrocarbons, but also for the prevention of the catalyst deactivation by carbon deposits. Titania support induced the so - called SMSI, and potassium seemed to act as an electronic modifier, giving rise to an electron enrichment of the metallic phase.

• Applied Chemistry for Engineering
• /
• v.20 no.1
• /
• pp.87-93
• /
• 2009

Pd/activated carbon (Pd/AC) and Pd/alumina (Pd/AO) catalysts were prepared by the impregnation of palladium into activated carbon and alumina. The catalytic characteristics according to the kinds of support materials were compared. The decomposition efficiencies of ozone according to kinds of support materials are about the same when these were compared by adding 10 g of catalysts into the water saturated with ozone. The decomposition efficiencies and the oxidation characteristics (TOC, $COD_{Cr}$) of dichloroacetic acid were compared with the ozone only process and the catalytic ozonations using Pd/activated carbon and Pd/alumina catalysts. The decomposition efficiencies of dichloroacetic acid by catalytic ozonations were better than the one by ozone only process, but there was slight difference of the one between Pd/activated carbon and Pd/alumina catalyst. The decomposition efficiency of dichloroacetic acid was increased with increasing ozone dose at a constant concentration of dichloroacetic acid, but the one was little increased with increasing ozone dose at more than 1.0 L/min of ozone dose. It was seemed that the bicarbonate and the chloric ion formed throughout the decomposition of dichloroacetic acid acted as the scavenger of hydroxyl radical.

• Korean Chemical Engineering Research
• /
• v.45 no.2
• /
• pp.143-148
• /
• 2007

In hydrogen production for fuel cell by reforming city-gas, sulfur compounds, odorant in city-gas, are detrimental to reforming catalyst and fuel cell electrodes. We prepared metal salt impregnated ${\beta}-zeolite(BEA)$ to remove sulfur compound in city-gas by adsorption. The sulfur breakthrough adsorption capacity was changed depending on the concentration and species of metal salt. $AgNO_3$ impregnated BEA showed the highest sulfur breakthrough capacity among adsorbents used in this experiment(41.1 mg/g). But metal salt impregnated BEA such as $Ni(NO_3)_2/BEA$, $Fe(NO_3_)_3/BEA$, $Co(NO_3)_2/BEA$ showed a certain amount of sulfur adsorption capacity comparable to $AgNO_3/BEA$. Adsorption temperature effect, desorption study, and x-ray photoelectron spectroscopy analysis revealed that the dominant interaction between metal impregnated adsorbent and sulfur compounds was not chemisorption but physisorption.