• Journal of Welding and Joining
• /
• 제16권1호
• /
• pp.114-124
• /
• 1998

The effect of matrix phase (austenite, pearlite, martensite) on the low stress abrasion resistance in the chromium-carbide-type high Cr white iorn hardfacing weld deposites has been investigated. In order to examine matrix phase, a series of alloys with different matrix phase by changing the ratio of Cr/C system by heat treatment were employed. The alloys were deposited twice on a mild steel plate using self-shielding flux cored arc welding process. The low stress abrasion resistance of the alloys against sands was measured by the Dry Sand/Rubber Wheel Abrasion Test(RWAT). Even though formation of pearlite phase in the matrix showed higher hardness than that of austenite, there was no observable difference in wear resistance between the pearlite and austenite phase for the same amount of chromium-carbide in the matrix. On the other hand, the formation of martensitic phase,, from heat treated austenitic alloys (high content of Cr), enhanced wear resistance due to its fine secondary precipitates.

• Journal of Welding and Joining
• /
• 제16권1호
• /
• pp.125-133
• /
• 1998

The effect of volume fraction of Cr carbide phase (Cr CVF) on the low stress abrasion resistance in the chromium-carbide-type high Cr white iron hardfacing weld deposits has been investigated. In order to examine Cr CVF, a series of alloys with varying Cr CVF by changing chromium and carbon contents and the ratio of Cr/C were employed. The alloys were deposited once or twice on a mild steel plate using the self-shielding flux cored arc welding process. The low stress abrasion resistance of the alloys against sands was measured by the Dry Sand/Rubber Wheel Abrasion Test (RWAT). It was shown that hardness and abrasion resistance increased with increasing Cr CVF within the whole test range (Cr CVF : 0.23-0.64). Both primary Cr carbide and eutectic Cr carbide were particularly effective in resisting wear due to their high hardness.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1996년도 특별강연 및 추계학술발표 개요집
• /
• pp.114-116
• /
• 1996

• Journal of Welding and Joining
• /
• 제16권2호
• /
• pp.73-83
• /
• 1998

This study investigated the relationships between the microstructure and the wear resistance of hardfaced iron/chromium alloys to examine the low stress abrasive wear mechanism. The effects of volume fraction of reinforcing phases(chromium carbide and eutectic phase) were studied. The alloys were deposited once or twice on a mild steel plate using a self-shielding flux cored arc welding process. The low stress abrasion resistance of he alloys against dry sands was measured by the Dry Sand/Ruber Wheel Abrasion Tester (RWAT). The wear resistance of hypoeutectic alloys, below 0.36 volume fraction of chromium-carbide phase (VFC), behaved as Equal Pressure Mode (EPM) for the inverse rule of mixture whereas the wear resistance of hypereutectic alloys, above 0.36 VFC, represented Equal Wear Mode (EWM) for the linear rule of mixture.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1995년도 특별강연 및 추계학술발표 개요집
• /
• pp.23-26
• /
• 1995

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.3-8
• /
• 1996

To enhance the cutting performance of the tool, single or multilayer coating is applied on the substrate of the tool. Coating material reduces cutting force and heat generation in tool-chip contact zone and enhances resistance against abrasive wear. This paper presents that the effect of different coatings on abrasive wear resistance varies with work material and the flank wear rate is different with depth of cut. Crater wear rate is also found to decrease with higher thermal diffusivity of coating material. It is verified that the estimated thermal diffusivity of multilayer coating has consistent effect on the crater wear.

• 터널과지하공간
• /
• 제22권4호
• /
• pp.284-295
• /
• 2012

본 연구에서는 암석 절삭 장비의 마모에 직접적인 영향을 주는 인자인 암석의 마모도(abrasiveness) 측정에 관한 연구를 수행하였다. 몇 가지 방법 중 세르샤 마모 시험(Cerchar abrasiveness test)을 통하여 암석의 마모도에 영향을 미치는 인자를 확인하고 효율적인 시험을 수행하기 위한 조건들을 연구하였다. 국내 19종 암석에 대한 시험 결과를 통하여, 세르샤 마모 지수(CAI, Cerchar Abrasiveness Index)에 영향을 미치는 암석의 역학적 물성(단축압축강도, 간접인장강도, 탄성계수, 포아송비, 공극률, 쇼어경도)과의 상관관계를 찾아보았고 X선 회절 분석을 통하여 암석의 구성 광물 중 마모도에 가장 큰 영향을 미치는 석영 함량, 등가 석영 함량과의 관계도 확인하였다. 그 결과로 암석의 입자 결합 특성보다 광물의 특성이 CAI에 영향을 더 미치는 것으로 관찰되었고, 단축압축강도와 등가 석영함량의 함수로 CAI를 예측하는 모델을 제시하였으며 핀의 경도가 커질수록 CAI값이 선형적으로 작아짐을 확인하였다. 수치해석적 연구를 통해 세르샤 마모 시험을 모사한 결과 초기 긁힘 거리에서 대부분의 마모가 발생함을 확인하였고 하중이 증가할수록 CAI값이 증가함을 확인하였다.