• Korean Journal of Remote Sensing
• /
• v.33 no.5_1
• /
• pp.587-598
• /
• 2017

Volcanic ash is a fine particle smaller than 2 mm in diameters. It falls after the volcanic eruption and causes various damages to transportation, manufacturing industry and respiration of living things. Therefore diffusion information of volcanic ash is highly significant for preventing the damages from it. It is advantageous to utilize satellites for observing the widely diffusing volcanic ash. In this study volcanic ash diffusion information about two eruptions of Mt. Sakurajima were calculated using the geostationary satellite, Communication, Ocean and Meteorological Satellite (COMS) Meteorological Imager (MI) and polar-orbiting satellite, Landsat-8 Operational Land Imager (OLI) and the Thermal InfraRed Sensor (TIRS). The direction and velocity of volcanic ash diffusion were analyzed by extracting the volcanic ash pixels from COMS-MI images and the height was retrieved by adjusting the shadow method to Landsat-8 images. In comparison between the results of this study and those of Volcanic Ash Advisories center (VAAC), the volcanic ash tend to diffuse the same direction in both case. However, the diffusion velocity was about four times slower than VAAC information. Moreover, VAAC only provide an ash height while our study produced a variety of height information with respect to ash diffusion. The reason for different results is measured location. In case of VAAC, they produced approximate ash information around volcano crater to rapid response, while we conducted an analysis of the ash diffusion whole area using ash observed images. It is important to measure ash diffusion when large-scale eruption occurs around the Korean peninsula. In this study, it can be used to produce various ash information about the ash diffusion area using different characteristics satellite images.

• Korean Journal of Remote Sensing
• /
• v.36 no.5_4
• /
• pp.1267-1276
• /
• 2020

To quantitatively predict the impacts of large-scale volcanic eruptions of Mt. Baekdu on air quality and damage around the Korean Peninsula, a three-dimensional chemistry-transport modeling system (Weather Research & Forecasting - Sparse Matrix Operation Kernel Emission - Comunity Multi-scale Air Quality) was adopted. A worst-case meteorology scenario was selected to estimate the direct impact on Korea. This study applied the typical worst-case scenarios that are likely to cause significant damage to Korea among worst-case volcanic eruptions of Mt. Baekdu in the past decade (2005~2014) and assumed a massive VEI 4 volcanic eruption on May 16, 2012, to analyze the concentration of PM_2.5 caused by the volcanic eruption. The effects of air quality in each region-cities, counties, boroughs-were estimated, and vulnerable areas were derived by conducting an exposure assessment reflecting vulnerable groups. Moreover, the effects of cities, counties, and boroughs were analyzed with a high-resolution scale (9 km × 9 km) to derive vulnerable areas within the regions. As a result of analyzing the typical worst-case volcanic eruptions of Mt. Baekdu, a discrepancy was shown in areas between high PM_2.5 concentration, high population density, and where vulnerable groups are concentrated. From the result, PM_2.5 peak concentration was about 24,547 ㎍/㎥, which is estimated to be a more serious situation than the eruption of Mt. St. Helensin 1980, which is known for 540 million tons of volcanic ash. Paju, Gimpo, Goyang, Ganghwa, Sancheong, Hadong showed to have a high PM_2.5 concentration. Paju appeared to be the most vulnerable area from the exposure assessment. While areas estimated with a high concentration of air pollutants are important, it is also necessary to develop plans and measures considering densely populated areas or areas with high concentrations of susceptible population or vulnerable groups. Also, establishing measures for each vulnerable area by selecting high concentration areas within cities, counties, and boroughs rather than establishing uniform measures for all regions is needed. This study will provide the foundation for developing the standards for disaster declaration and preemptive response systems for volcanic eruptions.

• Journal of Veterinary Clinics
• /
• v.26 no.4
• /
• pp.353-358
• /
• 2009

Unilateral ureteronephrectomy was performed in a dog presented with unilateral hydroureter and hydronephrosis. On laparotomy, severe adhesion of the dorsomedial border of the affected kidney to the abdominal aorta longitudinally and caudal pole of the kidney firmly to the ipsilateral ovary were observed. Since it was not possible to ligate the renal artery and vein separately due to severe adhesion tissue, two mass ligations were applied in the medial border of kidney, and the adhesion tissue was transected distal to each ligature. Then, blunt and sharp dissections were performed to isolate dorsomedial border of the kidney from the abdominal aorta, but they brought out unexpected hemorrhage caused by incision of renal artery and it has been suspected that two mass ligations could not include renal artery, which was adhered to dorsomedial border of the kidney. The hemorrhage was controlled by double ligations and electrocautery. In this case report, we recommend that if isolation of renal vessels is impossible due to strict adhesion of kidney to adjacent tissue, the mass ligation could be chosen to isolate and exteriorize the kidney and placed carefully not only at medial border of the kidney, where the renal vessels come into the kidney anatomically but also additional border of the kidney where adhesion tissues are formed.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.11 no.4
• /
• pp.1798-1802
• /
• 1969

The experiment was carried out as one of the basic studies to improve the alkali-resistance of cement mortars and it was conducted to investigate some propetties of mortars relating to weight losses when exposed to 0.1 N salution of sodium hydroxide. The experiment and the results obtained are summarized as follow; 1. The specimens used in this experiment were made of 5 centi-meter cubes of mortar having such various ratios of mix by weight as 1 : 1, 1 : 3, 1 : 5, 1 : 7 and 1 : 10. 2. Physical tests included compressive strengths at 7 days, 28 days, 3 months, and 6 month, and 5 hour boiling absorption test. 3. In alkali test, every specimen was immersed into 0.1 N solutions of sodium hydroxide. The specimens exposed to the alkali solution were weighed to determine the weight losses of the alkail-corroded at one week interval for 7 week's exposure and the old alkali solutions were also changed to fresh solutions when weighed the weight losses by alkali attack at one week interval. 4. According to the alkail test after 7 week's exposure, no weight losses were observed on ratios of mix 1:1 and 1:3 and slight weight losses occurred on ratios of mix 1:5 and 1:7, but relatively large amount of weight losses were showed by 36.6 per-cent on ratios of mix 1:10. It was also found that the weight losses of the alkali-corroded were extremely lower than those of the acid-corroded at the some concentrations as 0.1 N of solutions. 5. In order to make better quality of alkali-resistant mortar it might recomend that a 1:7 mix or richemixes, use of small amount of mixing water for watertight, 20 per cent or less absorption by 5 hour boiling 1,600 kirogram per cubic meters or denser densities by absolute dry base are available for physical properties of mortar. It could conclude acid-resistant mortars were so high alkali-resistant, that it is expected to make and improve the acid-resistant mortars for getting rid of damages by alkali attack.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.9
• /
• pp.717-722
• /
• 2001

This paper presents a methodology on the backward path tracking control of a trailer type robot which consists of two parts: a tractor and a trailer. It is difficult to control the motion of a trailer vehicle since its dynamics is non-holonomic. Therefore, in this paper, the modeling and parameter estimation of the system using a real-coded genetic algorithm(RCGA) is proposed and a backward path tracking control algorithm is then obtained based on the linearized model. Experimental results verify the effectiveness of the proposed method.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.09a
• /
• pp.21-36
• /
• 2005

Although the main geology of Korea consists of granite and gneiss, it Is not uncommon to encounter anisotropy Phenomena in crosshole radar tomography even when the basement is crystalline rock. To solve the anisotropy Problem, we have developed and continuously upgraded an anisotropic inversion algorithm assuming a heterogeneous elliptic anisotropy to reconstruct three kinds of tomograms: tomograms of maximum and minimum velocities, and of the direction of the symmetry axis. In this paper, we discuss the developed algorithm and introduce some case histories on the application of anisotropic radar tomography in Korea. The first two case histories were conducted for the construction of infrastructure, and their main objective was to locate cavities in limestone. The last two were performed In a granite and gneiss area. The anisotropy in the granite area was caused by fine fissures aligned in the same direction, while that in the gneiss and limestone area by the alignment of the constituent minerals. Through these case histories we showed that the anisotropic characteristic itself gives us additional important information for understanding the internal status of basement rock. In particular, the anisotropy ratio defined by the normalized difference between maximum and minimum velocities as well as the direction of maximum velocity are helpful to interpret the borehole radar tomogram.

• Korean Journal of Remote Sensing
• /
• v.30 no.4
• /
• pp.481-491
• /
• 2014

Blue-ice area is a glacial ice field in ice sheet, ice shelf and glaciers where snow ablation and sublimation is larger than snowfall. As the blue-ice area has large influences on the meteorite concentration mechanism and ice mass balance, it is required to quantify the concentration of blue-ice. We analyzed spectral reflectance characteristics of blue-ice, snow and cloud by using MODIS images obtained over blue-ice areas in McMurdo Dry Valleys, East Antarctica, from 2007 to 2012. We then developed Normalized Difference Blue-ice Index (NDBI) algorithm which quantifies the concentration of blue-ice. Snow and cloud have a high reflectance in visible and near-infrared (NIR) bands. Reflectance of blue-ice is high in blue band, while that lowers in the NIR band. NDBI is calculated by dividing the difference of reflectance in the blue and NIR bands by the sum of reflectances in the two bands so that NDBI = (Blue-NIR)/(Blue + NIR). NDBI calculated from the MODIS images showed that the blue-ice areas have values ranging from 0.2 to 0.5, depending on the exposure and concentration of blue-ice. It is obviously different from that of snow and cloud that has values less than 0.2 or rocks with negative values. The change of NDBI values in the blue-ice area has higher correlation with snow depth ($R^2=0.699$) than wind speed ($R^2=0.012$) or air temperature ($R^2=0.278$), all measured at a meteorological station installed in McMurdo Dry Valleys. As the snow depth increased, the NDBI value decreased, which suggests that snow depth can be estimated from NDBI values over blue-ice areas. The NDBI algorithm developed in this study will be useful for various polar research fields such as meteorite exploration, analysis of ice mass balance as well as the snow depth estimation.

• Korean Journal of Food Science and Technology
• /
• v.36 no.3
• /
• pp.416-422
• /
• 2004

Efficacy of surface sterilization and physicochemical properties of electrolyzed water manufactured depending on electrolyte, materials, and type of electrolytic diaphragm used were investigated. Physical properties of electrolyzed water manufactured from diaphragm system showed the highest effectiveness under at distance between diaphragms of 1.0 mm and 20% NaCl supplying rate of 6 mL/min. ORP, HClO (should defined) content, and pH at above conditions were 1,170 mV, 100 ppm, and 2.5, respectively. Two-stage electrolyzed system was more effective than one-stage one. Electrolyzed water manufactured from non-diaphragm system at 4 mL/min supplying rate of 20% NaCl was similar to the most effective diaphragm system, whereas ORP, HClO content, and pH were 800 mV, 200 ppm, and 9, respectively. Sealed electrolyzed water could be preserved more than one month at room temperature with ORPs of 750 and 1,150 mV in non-diaphragm and diaphragm systems, respectively, and at HClO content of 100 ppm. Physicochemical properties of electrolyzed water manufactured from electrolytic diaphragm of $IrO_{2}$ and Pt+Ir were more effective than that of Pt. ORP and HClO contents of electrolyzed water manufactured from various electrolytes were high in order of NaCl>KCl>$CaCl_{2}$, whereas no differences were observed among electrolytes in sterilization efficacy. Twelve kinds of microorganisms tested (initial total count, $10^{5}-10^{6}CFU/mL$) were sterilized within 1-2 min by electrolyzed water.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.2
• /
• pp.30-37
• /
• 1964

Experiments were carried out to clarify the relationships between seed yields and some ecological characteristics, seed yields and some morphological characteristics, and the relationships among the varietal yields on the several sowing plots when grown under different climatic conditions. Twenty-four soybean varieties were used as the material, selected at random from 138 varieties which were cultivated the year before. These varieties were grown in the Experimental Farm, Chinju Agricultural College, Kyung Sang Namdo, Korea, and seed sowing was conducted at 5 times, from April to July, in 1962 and 1963. The results obtained are summarized as follows: 1. Correlations between seed yields and some ecological characteristics on the sowing date bases are shown in Table 1. Among some ecological characteristics, it was observed that there wert close relationships between seed yields and days to flowering, and between seed yields and the total growing length, except on the late sowing, i.e. July sowing plots, However, there was no clear correlation between seed yields and durations of flowering, and between seed yields and days from flowering to maturity. 2. Correlations between seed yields and some morphological characteristics on the sowing date bases are shown in Table 2. From this table, it was also observed that there were some close relationships between seed yields and branch number for plant, stem diameter, plant weight, pod number per plant, and grain number per plant, but there was no clear relationship between seed yields and stem length, and between seed yields and 100 grain weight, on every sowing plot. 3. Relations between varietal yields and the sowing dates are shown in Table 3. Our leading varieties such as Ulsan, Sangdoo, Changdan Backmok, Iksan, Haman, Barchongdeo, and Anion Daerip, which belong to the maturity groups of IV, V, and VI, have been significantly high in yield at each sowing date plot, but the extreme early varieties, that frequently are damaged by insects, moisture and diseases, and the extreme late varieties, that frequently are caught by frost suffering reduced yield, are showed a lower yield than the others. However, extreme early varieties, for instance, Black Hawk, an American variety, and Chung Buk Baek, a Korean early variety, showed high productivity on the late sowing, June and July sowing plots, and Do san No. 6, which is late Japanese variety, showed a high yield on the extreme early sowing, i.e. April sowing plots. 4. Relations between seed yields and the sowing dates on the varietal bases are shown in Table 4. It was observed that, the early varieties did not differ much in yields at the various sowing dates while the yields of late varieties decreased progressively with subsequent dates. However, the extreme late varieties, such as Tamanishiki, that frequently are caught by frost suffering reduced yield, may be difficult to harvest at this location. The results in these experiments showed that in most cases maximum yields were obtained when leading varieties, which are medium or late varieties, were shown in Mid-May, and progressively lower yields were produced from June and July sowings. On the other hand, the late sowings of the early varieties, such as Black Hawk and Chung Buk Baek, in these experiments showed favorable yields compared with the others. From these results, we can predict that our local medium or late varieties produce higher yields at this location than was produced by early varieties in most of the sowing dates, especially the May sowing, and early varieties such as Black Hawk and Chung Buk Baek should be used in the late sowing, June sowing time.

• Archives of design research
• /
• v.18 no.2 s.60
• /
• pp.37-46
• /
• 2005

Today's advertisement is dominated by visual images, which deliver messages in the most efficient and engaging way. Vivid and live images, through multimedia, attract the viewer to consume the products being advertised. In this course, the effect of 'Verfremdung' or alienation is often detected. This terminology was at first used in a epic play of Bertolt Brecht to signify a specific effect to block the empathy of the audience by reminding them of their position as the audience separate from the play. 'Verfremdung' helps them to have a sense of objectivity and critical attitude toward the performance. Multimedia commercials nowadays exhibit such a quality together with 'viewer participation:' criticism on reality: and 'speed.' In an advertisement for Shinsegi Communications' mobile system titled <017-I-Touch series, the hand transformed into a web>, the copy, 'my blood type is 'i', ' is accompanied by six unrelated fictitious scenes in which the same ocean appears as a common denominator. Because there is no connection between the scenes, free imagination of the viewer has to be involved and thus plays a significant role in making them into a context. This fact dearly exhibit some characteristics of post- modern advertisement. Momentary 'Gap' and 'Difference' between scenes contribute to 'Verfremdung' or alienation' that makes it hard for the consumers to comprehend the content on the spot. Such an uneasy situation, however, keeps the viewers thinking about the advertisement itself. While repeatedly exposed to the alienated images, the viewers come to get involved in the advertisement, trying to make the fragmented images into a coherent context. In addition, the leaps between the scenes produce a sense of 'speed' in a context, which adds more impact to the way of delivering messages using multimedia. With the help of multimedia, 'Verfremdung: which was originally intended to bring about objective and critical altitude of the audience in a play, plays a crucial role in attracting the viewer's attention and conveying a specific message in a moment in contemporary advertisement.