• 한국전산유체공학회:학술대회논문집
• /
• 1999.05a
• /
• pp.73-78
• /
• 1999

극초음속 유동장의 정확한 해석을 위해 AUSMPW+ 수치기법과 충격파 포착시 생기는 수치오차를 제거하기 위해 충격파 정렬 기법(Shock-Aligned Grid Technique)을 개발하였다. AUSMPW+ 수치기법은 자체 수치점성이 적은 수치기법으로 점성 경계층 계산시 정확한 계산결과를 보여주며 기존의 AUSM 계열이 가지는 문제점인 물성치의 진동 현상을 제거한 수치기법이다. 원통형과 무딘 물체 주위의 극초음속 유동장 해석을 통해 공력이 진동현상 없이 정확하게 계산됨을 확인하였다. 그리고 충격파 정렬 기법의 특성을 파악하기 위해 충격파 반사문제와 충격파-충격파 상호작용 문제를 해석하여 수치오차 없이 충격파를 포착할 수 있음을 보였다. 또한 화학적 평형 비평형 유동 영역까지 충격파 정렬 격자 기법을 확장하였다.

• Proceeding of EDISON Challenge
• /
• 2016.11a
• /
• pp.63-67
• /
• 2016

본 연구에서는 극초음속 추진기관을 위한 고공환경 모사 설비 장치에서 시험부 안에 들어가는 시험 모델의 변수에 대해 고찰하였다. 시험부에 적용할 시험 모델을 대상으로 진행하고, 시험 모델 형상 변화에 따른 유동 특성을 파악하였다. 시험 모델에 대한 주요 변수는 폐색율, 각도, 받음각으로 설정하였으며, 해석은 EDISON_CFD에서 제공하는 정렬격자 기반 2차원 압축성 유동 범용 해석 SW로 진행하였다. 해석 결과를 통해 다양한 형상 변수에 따라 변화 되는 충격파 뒤의 압력층 두께를 확인 하였고, 압력층 두께가 두꺼워 질수록 시험 조건을 모사 할 수 없음을 확인하였다. 본 연구를 통해 형상 변수에 따른 극초음속 추진기관을 위한 고공모사설비에서 시험부에 적용될 시험 모델의 범위를 확인하였다.

• Proceeding of EDISON Challenge
• /
• 2016.11a
• /
• pp.78-80
• /
• 2016

우주발사체와 항공 분야에서 초음속과 극초음속 영역에서 비행체의 항력을 최소화하기 위한 최적 형상설계 연구가 활발히 진행되고 있다. 본 논문에서는 마하수 2의 초음속 영역에서 대표적인 비행체 선두부 형상 3가지에 대한 수치해석을 eMEGA 프로그램을 활용해 격자를 생성하고 eDAVA 프로그램을 활용해 유동 해석을 수행하였다. 그 결과 자유유동 마하수 2의 초음속 영역에서는 선두부 형상이 뾰족한 Cone 형상이 3가지 형상 중 작용하는 항력이 가장 적게 나타났고, 선두부가 무딘 형상이 극초음속 영역에서 가장 적합한 현상과 다르게 나타났다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.6
• /
• pp.562-570
• /
• 2009

An Experimental study was conducted on the flow characteristics and interference heating caused by a two-dimensional object protruding from a flat plate using a blow-down type of hypersonic wind tunnel. Inflow condition was a free-stream Mach number of 7.0 and a unit Reynolds number of $2.0{\times}10^6/m$. Experimental conditions were varied with three heights of protuberance for two flat plate models which have different lengths. Experimental data were obtained from Schlieren visualization images and heat flux measurements. Also, this paper suggests hypersonic experimental techniques such as boundary-layer detection method in detail. A Large separation region was observed in front of the protuberance and that region was very sensitive to the height of protuberance and the length of the flat plate. For only the highest protuberance, a severe jump of heat flux was observed at the top station among the measuring points. Measured heat flux is large when the height of protuberance is large and the length of flat plate is long.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.7
• /
• pp.1-8
• /
• 2003

Numerical characteristics of air chemistry associated with hypersonic flows are described and are compared with those of hydrogen oxygen combustion, applying the partially implicit time integration method to air chemistry. This paper reveals that the time integration of air chemistry needs a chemical Jacobian for stable calculations. However the positive real eigenvalues in air chemistry are relatively smaller than those of hydrogen combustion, and the numerical integration is less sensitive than that with combustion. lt is also found that the application of the partia1ly irnplicit method reduces the computing time without numerical instabilities.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.3
• /
• pp.113-126
• /
• 2021

In order to develop active cooling systems for a hypersonic cruise vehicle, a series of studies need to be preceded on regenerative cooling technologies by using endothermic reaction of liquid hydrocarbon aviation fuels. Among them, it is essential to scrutinize fluid flow/heat transfer/endothermic pyrolysis characteristics of supercritical hydrocarbons in a micro-channel, as well as to acquire thermophysical properties of hydrocarbon fuels in a wide range of temperature and pressure conditions. This study, therefore, reviewed those technologies and analyzed major findings in related research areas which have been carried out worldwide for the development of efficient operational regenerative cooling systems of a hypersonic flight vehicle.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.3 s.18
• /
• pp.165-173
• /
• 2004

Matching inviscid and boundary layer methods are developed for analysis of hypersonic flow with thick boundary layer. The new equations match all the boundary layer properties with a variation in the inviscid solution near the edge, except for the normal velocity. Computational comparison are peformed for incompressible and compressible flows over a flat plate. Results from the present method are compared with Wavier-Stokes solutions. The present results are in good agreement with Wavier-Stokes solutions. They show that the new technique can provide improved predictions of heating rates and skin friction predictions for preliminary design of vehicles where shear layers and entropy layer swallowing are importantfor for preliminary design.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.4
• /
• pp.321-327
• /
• 2008

The shock tunnel as a hypersonic ground test facility was designed, constructed and its performance test was conducted to reproduce the high speed flow which the hypersonic propulsion system is encountered. The design points were understood and the conceptual design was completed using the quasi one dimensional operation analysis code. After that, the specific performance and compartment design were completed using CFD simulation as the part analysis. The facility was then constructed according to those design results and the performance test was conducted for various operation conditions. In this paper, we suggested the design method of hypersonic shock tunnel including the conceptual and performance design using theoretical analysis and the quasi 1D Multi-species computational fluid dynamics code.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.41-44
• /
• 2007

Ground test facility for the hypersonic propulsion system was designed, constructed and performance test was conducted. The design point was selected using quasi，1-Dimensional CFD analysis before the conceptual design for construction of hypersonic facility After that, specific designs for performance and components were completed using unit analysis CFD code and performance tests were conducted for the various operation conditions.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.4
• /
• pp.328-336
• /
• 2008

The shock tunnel as a hypersonic ground test facility was designed, constructed and its performance test was conducted to reproduce the high speed flow which the hypersonic propulsion system is encountered. The design points were understood and the conceptual design was completed using the quasi one dimensional operation analysis code. After that, the specific performance and compartment design were completed using CFD simulation as the part analysis. The facility was then constructed according to those design results and the performance test was conducted for various operation conditions. In this paper, we suggested the compartment design method using CFD analysis, construction process and various performance test results in detail.