• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1259-1268
• /
• 2010

In this paper, we presented a new LC prototype synthesis method for the multi-band filter. For synthesis a multi-band filter with the required frequency response, we proposed the diagram of poles and zeros, also, we proposed the optimization process for finding the combination of optimized poles and zeros. From the transfer and reflection functions calculated from poles and zeros, we performed the quasi-elliptic LC prototype synthesis of multi-band filter. Using the proposed LC prototype synthesis method of multi-band filter, dual-band filter operating at GSM(880~960 MHz) and ISM(2,400~2,500 MHz) and triple-band filter operating at GSM(880~960 MHz) and ISM(2,400~2,500, 5,725~5,850 MHz) were designed and fabricated.

• The Journal of the Petrological Society of Korea
• /
• v.9 no.4
• /
• pp.205-210
• /
• 2000

Measurements of phase identification and degree of orientation for fine-grained (about 0.3 mm in diameter) minerals in rock samples performed by micro-area X-ray diffractometer.$Al_{2}SiO_{5}$ polymorphs (andalusite, kyanite and sillimanite) were chosen for the measurements and target minerals were existed on thin sections. Micro-area X-ray diffractometer is composed of 3(${\omega}\;{\chi}\;{\phi}$)-circle oscillating goniometer and position sensitive proportional counter (PSPC). $CuK_{\alpha}$ radiation was used as X-ray source and a pin hole ($50\;\mu\textrm{m}$$ in diameter) collimator was selected to focus radiation X-ray onto the target minerals. Phase identification and diffracted X-ray peak indexing were carried out by 3(${\omega}\;{\chi}\;{\phi}$)-circle oscillation measurement. Then, 2(${\omega}\;{\phi}$)-circle oscillation measurement was made for the purpose of searching the prevailing lattice plane of the minerals on thin section surface. Finally, for a selected peak by 2-circle oscillation measurement, X-ray pole figure measurement was executed for the purpose of check the degree of orientation of the single lattice direction and examine its pole distribution. As a result of 3-circle oscillation measurement, it was possible that phase identification among $Al_{2}SiO_{5}$ polymorphs. And from the results of 2-circle oscillation measurement and X-ray pole figure measurement, we recognized that poles of andalusite (122), kyanite (200) and sillimanite (310) lattice plances were well developed with direction normal to each mineral surface plane respectively. Therfore, the measurements used with micro-area X-ray diffractometer in this study will be a useful tool of phase identification and degree of orientation measurement for fine-grained rock forming minerals.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.480-484
• /
• 2000

The pole placement technique for control design of the current mode controlled DC-DC switchmode power converter is proposed. It is compared with conventional transfer function analysis. Using the pole placement technique control design automation algorithm, by computer-based tool is presented. Control design example with large signal simulation is shown.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.435-438
• /
• 1990

A new robust stabilizing method of uncertain system is proposed. The model uncertainty is considered to be the system matrix perturbations. The region of perturbed system eigenvalues are estimated by union of the disks which have the constant radius. Full state feedback control matrix which satisfies the new stabilization condition can be obtained by weighted LQ regulator or pole assignment technique.

• Journal of Industrial Technology
• /
• v.11
• /
• pp.27-31
• /
• 1991

Consider a problem to keep half of the poles unchanged when some of the coefficients of stable characteristic polynomials are perturbed. A procedure was proposed for the problem. However, the pole assignment procedure has not been addressed. A simple algorithm for the procedure is proposed in this paper.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.7
• /
• pp.80-84
• /
• 1999

In this paper, the split model analysis algorithm, which can generate the wideband speech signal from the spectral information of narrowband signal, is developed. The split model analysis algorithm deals with the separation of the 10/sup th/ order LPC model into five cascade-connected 2/sup nd/ order model. The use of the less complex 2/sup nd/ order models allows for the exclusion of the complicated nonlinear relationships between model parameters and all the poles of the LPC model. The relationships between the model parameters and its corresponding analog poles is proved and applied to each 2/sup nd/ order model. The wideband speech signal is obtained by changing only the sampling rate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.6
• /
• pp.499-504
• /
• 2001

We evaluated the degree of texture through depth of the superconductor core of Bi-Sr-Ca-Cu-O(BSCCO) superconductor tape. The degree of texture was characterized by pole figure analysis indicating that the degree of texture varied significantly with depth of the superconductor core. It was observed that the degree of texture was higher near the interface than inside the superconductor core. Specifically, as getting near to the center from the sheath/core interface, the orientation of BSCCO became dispersed from normal direction(ND) which, in turn, resulted in the degradation of <001>-fiber texture. In addition, the <001> texture was non-uniform an, better texture was developed along rolling direction(RD), compared to transverse direction(TD). Microstructural investigation showed that grain alignment was locally degraded by the existence of second phases. I was observed that larger grain size and better texturing were developed near the relatively straight interface compared to those inside the superconducting core. Based on our study, the region near the interface is thought to carry significant current compared to that inside the core.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.03a
• /
• pp.73-80
• /
• 1996

Commerical purity aluminium , copper and STS 304 stainless steel sheets are welded by ultrasonic welding. The microstructures, x-ray diffraction profiles of planes , pole figures of the surface of original metal sheets are compared with those of the weld interface. The microstructures show disturbance and dark areas in the weld interface and grain refinement in the vicinity of the interface. The x-ray diffraction intensity of each plane in weld interface decreased in all metal sheets with exception of 9200) in steel sheet. The microstructure and x-ray diffraction intensity is affected by the mixture of deformation, heating and vibratin duringthe ultrasonic welding. Therefore, after the ultrasonic welding, the positions of the peak intensity in the pole figures are changed, the value of the maximum pole intensity is decreased in Al, is increased in copper and stainless steel. Very strong {100} <001> texture, strong {100} <001>,{123}<634> textures in original Al surface are transformed into weak, {100}<001>, {110}<112> and {112}<111> components in weld surface, weak (110) fiber is slightly changed to (110) fiber in copper, (100)and ${\gamma}$ fiber components are transformed into strong ${\gamma}$ fiber component in stainless steel.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.190-193
• /
• 2002

3mol% $Y_2O_3$ Partially-Stabilized Zirconia single Crystals (PSZCs) containing a small quantity (<0.5%) of rare-earth oxides ($CeO_2,\;Tb_2O_3$) were prepared by using a direct high-frequency skull melting technique to evaluate hydrothermal stability in an autoclave. Pole exhibited no $t{\rightarrow}m$ phase transformation during aging for 5h at temperatures from 150 to 250$^{\circ}C$ and 4MPa water vapor pressure in an autoclave, resulting in excellent hydrothermal stability.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.287-290
• /
• 2005

The shearing and punching processes are analyzed with the finite element method using an isotropic material model. The experimental result in the punching process shows that final radiuses of sheet metal according to the rolling direction and transverse direction are different because of the material anisotropy. The material anisotropy is induced by complicated large deformation in the polycrystalline aggregate. The contact region between the punch and sheet metal experiences severe deformation such as shear, compression and tension in the punching process. In this paper, the analysis of punching process for Al 1100 is performed with the ABAQUS Standard. The analysis of texture development and evolution is carried out based on the deformation history in the punching process. The deformation histories are extracted by UMAT in the ABAQUS Standard. The torture development is investigated with the pole figure and yield surface during the punching process.