• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.3
• /
• pp.227-234
• /
• 2016

In this study, asphalt paving filler, which satisfies the KS standards, were prepared from industrial by-products, such as fly ash generated from thermal power plants, cogeneration ash generated from cogeneration plants, and desulfurized gypsum generated from the flue-gas desulfurization process. The properties of the prepared mixed filler and the existing limestone filler were compared through laboratory tests for preparing asphalt mixture using each filler. In addition, asphalt pavement field tests were conducted using the limestone filler and mixed filler. The dynamic stability, Marshall stability, tensile strength ratio, saturation, porosity, and flow value of the asphalt mixtures used in the field test were evaluated, as was done in the laboratory test. The laboratory and field construction test results revealed outstanding tensile strength ratio, Marshall stability and dynamic stability when using the prepared filler than for the existing limestone filler. Through optimization of the mixing design, the possibility of developing fillers, which the characteristics of the existing limestone filler, was confirmed.

• Journal of Broadcast Engineering
• /
• v.11 no.2 s.31
• /
• pp.222-228
• /
• 2006

In this paper, we propose a receive diversity method for orthogonal frequency division multiplexing (OFDM) systems with cochannel interference. In the method, combining is done in the frequency domain by using the subcarrier based maximum ratio combining (MRC) method. For MRC, we exploit the power of cochannel interference as well as the power of channel noise. The accuracy of the power estimate of interference plus noise is enhanced by averaging the initial estimates over the correlated subchannels where the coherency between the subchannel gains comes from the limited delay spread of the channel. Simulation results show that the proposed method yields 2-3.5dB gain of signal to noise ratio compared to the conventional MRC method and less than 1 dB difference to the ideal case.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.10
• /
• pp.1163-1169
• /
• 2012

Rubber, a hyperelastic material, is the main material used in tires. During the operation of a car, the tire receives various types of loads. The accumulation of strain energy due to such loads induces tire failure. Generally, because rubber materials used for tires have stress softening characteristics, unlike metals, test methods used for metals cannot be applied to rubber. Therefore, in this study, for the evaluation of the fatigue properties of two types of specimens that have different material components, a tensile test and a fatigue test according to the extended strain range dissimilar to ASTM D4482 are performed, and fatigue life equations are proposed based on the test results.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.7
• /
• pp.891-899
• /
• 2008

For the effective use of under-utilized resources, silver-stripe round herring (SSRH), the boiled-dried SSRH was investigated on the food component and sensual characterization. Moisture content and salinity of the boiled-dried SSRH were 27.2% and 7.0%, respectively, which were in the range described in Korean Industrial Standards. In the lipid content of the boiled-dried SSRH, viscera was higher in viscera than muscle. The major fatty acids of the boiled-dried SSRH were 16:0 (23.9%), 18:1n-9 (9.5%), and 22:6n-3 (DHA, 28.5%). The degree of lipid oxidation of the boiled-dried SSRH was similar to that of the boiled-dried anchovy caught in the southern sea. When compared to the boiled-dried anchovies, the boiled-dried SSRH was lower in total content of amino acid, while was higher in calcium and phosphorus contents. The boiled-dried SSRH was higher in taste strength, while was similar in the taste pattern to the boiled-dried anchovies. According to the results of chemical components and sensory evaluation, the boiled-dried SSRH could be substituted for boiled-dried anchovy classified into special grade.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.12
• /
• pp.23-35
• /
• 2023

The Ministry of Agriculture, Food and Rural Affairs has announced design standards for disaster-resilient greenhouses capable of resisting wind speeds with a 30-year frequency to respond to the destruction of greenhouses caused by strong winds. However, many greenhouses are still being maintained or newly installed as conventional standard facilities for the supply type. In these supply-type greenhouses, a small pile called a steel peg is used as reinforcement to resist wind-induced damage. The wind resistance of steel pegs varies depending on the soil environment and installation method. In this study, a correlation analysis was performed between the wind resistance of steel pegs installed in loam and sandy loam, using a soil hardness meter. To estimate the pull-out force of steel pegs based on soil water content and compaction, soil compaction tests and laboratory soil box and field tests were performed. The soil compaction degree was measured using a soil hardness meter that could easily confirm soil compaction. This was used to analyze the correlation between the soil compaction degree in the tests. In addition, a correlation analysis was performed between the pull-out force of steel pegs in the soil box and field. The findings of this study will be useful in predicting the pull-out force of steel pegs based on the method of steel peg installation and environmental changes.

• Journal of the Korean Applied Science and Technology
• /
• v.36 no.1
• /
• pp.324-332
• /
• 2019

Most countries including Korea and Indonesia have strong policy for implementing biofuels like biodiesel. Shortage of the oil feedstock is the main barrier for increasing the supply of biodiesel fuel. In this study, in order to improve the stability of feedstock supply and lower the biodiesel production cost, the feasibility of biodiesel production using two types of Indonesian tropical crop oils, pressed at different harvesting times, were investigated. R. Trisperma oils, a high productive non-edible feedstocks, were investigated to produce biodiesel by esterification and transesterification because of it's high impurity and free fatty acid contents. the kindly provided oils from Indonesia were required to perform the filtering and water removal process to increase the efficiency of the esterificaton and transesterification reactions. The esterification used heterogeneous acid catalyst, Amberlyst-15. Before the reaction, the acid value of two types oil were 41, 17 mg KOH/g respectively. After the pre-esterification reaction, the acid value of oils were 3.7, 1.8 mg KOH/g respectively, the conversions were about 90%. Free fatty acid content was reduced to below 2%. Afterwards, the transesterification was performed using KOH as the base catalyst for transesterification. The prepared biodiesel showed about 93% of FAME content, and the total glycerol content was 0.43%. It did not meet the quality specification(FAME 96.5% and Total glycerol 0.24%) since the tested oils were identified to have a uncommon fatty acid, generally not found in vegetable oils, ${\alpha}$-eleostearic acid with much contents of 10.7~33.4%. So, it is required to perform the further research on reaction optimization and product purification to meet the fuel quality standards. So if the biodiesel production technology using un-utilized non-edible feedstock oils is successfully developed, stable supply of the feedstock for biodiesel production may be possible in the future.

• Journal of Korean Society of Steel Construction
• /
• v.26 no.4
• /
• pp.299-309
• /
• 2014

HSA800 is a new high strength steel (HSS) plate for building structures developed by POSCO and RIST in 2011. It has upper and lower bounds for yield ($F_y$) and tensile ($F_u$) strength as of 650-770MPa and 800-950MPa, respectively, with yield ratio ($F_y/F_u$) limit as of 0.85 which make steel quality more reliable and enhance the seismic resistance of structures. As made by TMCP, it has a good weldability without increasing carbon percentage. The objective of this study is to provide alternative design of mega-structural members of the Lotte World Tower (555m, 123 story), a first super-tall building in Korea, using HSS considering structural safety, constructability, and cost-effectiveness. Steel outrigger trusses, belt-trusses and steel exterior columns were selected and analyzed to evaluate the structural performance between original and alternative designs using HSS. The results show that HSS can be applied to the members which do not affect lateral stiffness of a building and, in this study, approximately 1100tons of steel were saved. It implies that HSS can save overall construction costs - manufacturing, delivery, and erection costs - by reducing mega structural member size. HSA800 was very first applied to the Lotte World Tower based on the results of this study.

• Korean Journal of Soil Science and Fertilizer
• /
• v.40 no.4
• /
• pp.242-248
• /
• 2007

To find a feasibility of utilization of food waste slurry (FWS) generated during composting, FWS was combined with pig manure slurry (PMS) in various ratios and the change of nutrient contents and offensive odor of the combined slurries before and after fermentation were studied. The initial pH was 7.67 for PMS and 8.45 for FWS. However, during the fermentation, pH increased in the combined slurries with the higher FWS rate among the treatments while decreased in thosewith higher PMS rate. EC of each slurry sample showed that the difference among combined slurry samples has been reduced during fermentation and became stabilized in $21{\sim}23dS\;m^{-1}$ after 180 days. After 180 days fermentation, total nitrogen (T-N) decreased. T-N of mixture with a half and more FWS decreased up to 0.1%, less than the critical level (0.3%). The contents of O.M., T-N, phosphorus, calcium and magnesium decreased with fermentation while those of potash and salinity increased. From initial fermentation until 30 days, a lot of $NH_3$, as an offensive odor, was produced. However, it decreased steadily, except in higher PMS rate. In terms of producing $50{\mu}g\;ml^{-1}$ of $NH_3$, the top layer took 30 days after fertilization with FWS only, 45 days for utilized treatment with F75 (25 % of PMS), 75 days for utilized with F50 (50%) and F25 (75%) and 90 days for PMS only, respectively. $RNH_2$ also had similar trend with $NH_3$ but it was produced continuously as long fermentation proceeded. In terms of $RNH_2$, the decrease in concentration up to $50{\mu}g\;ml^{-1}$ were; 45 days for FWS only(F100), 105 days for F75 utilization, 120 daysfor F50, 165 days for F25, respectively. ethyl mercaptan was produced in PMS until 180 days after fertilization but it was not produced in FWS. Sensory tests as an integrated test of offensive odor were also done. FWS showed lower than 1 after 30 days from initial fermentation, while PMS had still offensive odor even up to 180 days from initial fermentation. It is probably affected by the continuous production of ethyl mercaptan and amines. However, considering in decrease T-N content caused by volatilization while offensive odor intensity according to official standard of fertilizer is lower than 2. Further study on controlling offensive odor needs to be done.

• The korean journal of orthodontics
• /
• v.32 no.1 s.90
• /
• pp.19-31
• /
• 2002

To investigate the association between the hypertrophy of adenoid and jaw morphology during growth, this paper was based on children patients with experimental adenoids (male-15 subjects at each bone age group, female-15 subjects at each bone group) and comparing them to data taken from a control group (male-15 subjects at each bone age group, female-15 subjects at each bone group) with normal respiratory function. The comparisons between the groups were done at each growth stage using cervical vertebrae maturation index(CVMI) of Hassel. The obtained results were as follows : 1. The differences in craniofacial morphology between experimental group and control group were appeared from CVMI 3 and CVMI 4 (aroud adolescent period) in males, and from CVMI 1 in females. 2. The mandibular position of experimental group was more inferior than control group. The difference appeared at adolescent period(male : at CVMI 4, female : at CVMI 5). 3. Experimental group had greater anterior facial height than control group. This difference seemed a relation with lower anterior facial height. The difference appears at CVMI 3(11.94 ${\pm}$ 1.38 years old, at adolescent period) in male and at CVMI 1 in female. 4. The adenoid size of control male group was increased until CVMI 2(10.58 ${\pm}$ 1.07 years old, just before adolescent growth peak) and then decreased, but in female the adenoid size was decreased from CVMI 1(6.92 ${\pm}$ 0.53 years old).