• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.4
• /
• pp.276-284
• /
• 2000

The acoustic emission (AE) behavior of reinforced concrete beams tested under flexural loading was investigated to characterize and identify the source of damage. This research was aimed at identifying the characteristic AE response associated with micro-crack development, localized crack propagation, corrosion, and debonding of the reinforcing steel. Concrete beams were prepared to isolate the damage mechanisms by using plain, notched-plain, reinforced, and corroded-reinforced specimens. The beams were tested using four-point cyclic step-loading. The AE response was analyzed to obtain key parameters such as the time history of AE events, the total number and rate of AE events, and the characteristic features of the waveform. Initial analysis of the AE signal has shown that a clear difference in the AE response is observed depending on the source of the damage. The Felicity ratio exhibited a correlation with the overall damage level, while the number of AE events during unloading can be an effective criterion to estimate the level of corrosion distress in reinforced concrete structures. Consequently, AE measurement characterization appears to provide a promising approach for estimating the level of deterioration in reinforced concrete structure.

• The Journal of Korean Academy of Prosthodontics
• /
• v.55 no.4
• /
• pp.389-393
• /
• 2017

Purpose: The aim of this study is to evaluate the flexural strength of flexible resins and the flexibility of different resin splint (RS) systems in comparison with resin wire splint (RWS) system. Materials and methods: Three different resin materials (G-aenial flo, GA, GC; Superbond, SB, Sun medical; G-fix, GF, GC) were tested flexural strength test in accordance with ISO-4049:2000. For the flexibility test of splint systems, a artificial model with resin teeth was used to evaluate three types of resin splint systems (GA, SB, and GF) and one resin wire splint system. The left central incisor was simulated 'injured teeth' with third degree mobility. Three consecutively repeated measurements of periotest value were taken in horizontal direction, before and after splinting to access tooth mobility. The splinting effect was calculated through the periotest value. Differences were evaluated through One-way Anova and Tukey HDS post-hoc tests for pair-wise comparison (${\alpha}=.05$). Results: Although GA group showed significant higher flexural strength than SB and GF groups, all of three different resin splint systems produced a significantly higher and rigid splinting effect compared with 016" resin-wire splint system (P < .05). Conclusion: Within the limits of an in vitro study, it can be stated that resin splint systems are too rigid and may not be acceptable to treat tooth avulsion.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.284-290
• /
• 2020

This study was undertaken to determine the effects of SNAGs (sustained natural apophyseal glides) and visual convergence biofeedback on the proprioception and neck disability of patients with chronic neck dysfunction. A total of 31 patients with neck dysfunction were assigned to either SNAGs (n = 16) or biofeedback (n = 15). The groups were assessed for proprioception and neck disability, before and after the intervention. The SNAGs were performed using belt with flexion, extension and right-left rotation, whereas biofeedback training included visual feedback training with deep neck flexor. Intervention was implemented for 20 minutes, twice a week for 4 weeks. Biofeedback training a showed significant effect on the joint position sense (left and right rotation) as compared to the SNAGs group (p< 0.05), whereas neck disability index was significantly effective for SNAGs (p< 0.05). Ed. Notes: The previous statement lacked clarity. I have suggested the edit as per my understanding. Please review and revise appropriately, if required. Therefore, the SNAGs technique is effective for neck function, and biofeedback training is a positive intervention method for enhancing the proprioceptive sensation. In future studies on patients with neck pain, it may be possible to select an intervention method based on the characteristics of the disease.

• Fashion & Textile Research Journal
• /
• v.24 no.6
• /
• pp.667-685
• /
• 2022

This paper aims to investigate 4D printing materials for soft robots. 4D printing is a targeted evolution of the 3D printed structure in shape, property, and functionality. It is capable of self-assembly, multi-functionality, and self-repair. In addition, it is time-dependent, printer-independent, and predictable. The shape-shifting behaviors considered in 4D printing include folding, bending, twisting, linear or nonlinear expansion/contraction, surface curling, and generating surface topographical features. The shapes can shift from 1D to 1D, 1D to 2D, 2D to 2D, 1D to 3D, 2D to 3D, and 3D to 3D. In the 4D printing auxetic structure, the kinetiX is a cellular-based material design composed of rigid plates and elastic hinges. In pneumatic auxetics based on the kirigami structure, an inverse optimization method for designing and fabricating morphs three-dimensional shapes out of patterns laid out flat. When 4D printing material is molded into a deformable 3D structure, it can be applied to the exoskeleton material of soft robots such as upper and lower limbs, fingers, hands, toes, and feet. Research on 4D printing materials for soft robots is essential in developing smart clothing for healthcare in the textile and fashion industry.

• Composites Research
• /
• v.16 no.2
• /
• pp.26-32
• /
• 2003

Optical fibers, for splice, are stripped of their plastic coatings with a plastic stripper and cut off at the end. Therefore, stripped fibers often receive accidental damages and sustain small flaws or cracks. As a result, the breaking strength of a fiber splice made under normal conditions is reduced to about 0.4∼1 ㎏ on the average, nearly one-tenth of the fiber's strength. This makes it necessary to reinforce the splice. One of the most practical and reliable methods for optical fiber splicing is fusion splicing, comprising the steps of tripping the plastic coatings from the two fiber ends to be splice, placing the two bare fiber ends in an end-to-end position, and of fusion splicing, such as are fusion. Generally, steel bar (SB) sleeve is used to reinforce this fusion-splicing region. However, this type of sleeve has a critical defect to keep optical lose after bent by a sudden load. New type of composite spring (CS) sleeve is developed to make up for the weak points in the SB sleeve. This sleeve has an effect on restoration to the original state after eliminating the bending load. The optical spectrum analyzes results show the availability of reinforcement for the fusion splicing optical fiber using small diameter composite springs under the various loading conditions.

• Composites Research
• /
• v.12 no.5
• /
• pp.40-53
• /
• 1999

The interlaminar facture behavior of multidirectional carbon-fiber/epoxy composite laminates under low and high rates of test, up to rate of about 11.4m/s has been investigated using the double cantilever beam specimens. The mode I loasing with rates above 1.0m/s had considerable dynamic effects on the load-time curves and thus revealed higher values of the average crack velocity than thet expected from a simple proportional relationship with the test rate. The modified beam analysis utilizing only the opening displacement and crack length exhibited an effective means for evaluating the dynamic fracture energy $G_{IC}$. Flexural modulus increased gradually with an increase of the test rate, which was utilized in the evaluation of $G_{IC}$. Values of $G_{IC}$ at the crack initiation and arrest were scarcely changed with increasing test rate up to 1.0m/s. However the maximum $G_{IC}$ was much enlarged at 11.4m/s due to the large amount of fiber bridging the crack tip. The larger the initial crack length, the smaller the maximum $G_{IC}$ at high rate.

• Composites Research
• /
• v.35 no.6
• /
• pp.463-468
• /
• 2022

The high porosity of the infill pattern of carbon chopped fiber-reinforced Nylon composite structures fabricated by the fused filament fabrication (FFF) type 3D printers determines the mechanical performance of the printed structures. This study experimentally evaluated the mechanical performance of Onyx composite specimens fabricated with a rectangular infill structure under the hot-pressing condition to improve the mechanical properties by reducing the porosity of the infill pattern of the printed structure, and evaluated the best mechanical performance. The hot-pressing conditions (145℃, 4 MPa, 12 min) that induce the most appropriate mechanical properties were found. As a result of microscopic observation, it was confirmed that the infill porosity of the composite specimens subjected to post hot-pressing treatment was effectively reduced. In order to confirm the mechanical performance of the post-treated specimen, a tensile test and a three-point bending test were performed with a control specimen without post-treatment and a specimen printed with the same density and dimensions after post-treatment to evaluate the mechanical properties. As a result of comparison, it was confirmed that the mechanical properties were effectively improved when the post-treatment of hot-pressing was performed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.2
• /
• pp.217-223
• /
• 1999

In this study, the effects of the content of $ZrO_{2}$ in $Si_{3}N_{4}$ on mechanical and wear properties were investigated. $Si_{3}N_{4}$ based composites containing 0~40 wt% $ZrO_{2}$ powders were fabricated using hot isostatic pressing (HIP), at $1750^{\circ}C$, 172 MPa for 1 hour in $N_{2}$ gas. Mechanical properties and wear properties of composites were examined. Mechanical properties (hardness, strength, and fracture toughness) of $Si_{3}N_{4}-ZrO_{2}$ composite were decreased with increasing the amount of $ZrO_{2}$, but relative density of composites were increased. Further, the increase in amount of $ZrO_{2}$, reduced wear rates in air. It was found that wear behaviors in air were related to microcracking.

• Journal of The Korean Society of Integrative Medicine
• /
• v.5 no.4
• /
• pp.31-39
• /
• 2017

Purpose : The purpose of this study was to examine the effects of short neck flexor strengthening in proprioceptive neuromuscular facilitation and neuromuscular electrical stimulation on swallowing function in patients with chronic stroke and to provide basic data for swallowing rehabilitation in stroke patients. Method : The study involved 30 chronic stroke patients who visited ${\bigcirc}{\bigcirc}$ General Hospital in Daegu Metropolitan City between March and July, 2017. The subjects were randomly assigned to either an experimental group (n=15) or a control group (n=15). Both groups underwent traditional swallowing rehabilitation therapy for 30 minutes five times a week over a six-week period. The experimental group performed short neck flexor exercises, which are part of the proprioceptive neuromuscular facilitation, for 30 minutes three times a week over a six-week period. The control group performed neuromuscular electrical stimulation for 30 minutes three times a week over a six-week period. Based on its results, changes in the patients' swallowing function and degree of food intake were analyzed. Result : In terms of the ASHA NOMS scale and new VFSS scale, the experimental group and the control group showed statistically significant changes in ten sub-items and six sub-items, respectively. Statistically significant differences in one sub-item were found between the groups. Conclusion : PNF-based short neck flexion exercise appear to be effective at improving swallowing function of stroke patients with dysphagia.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.3
• /
• pp.99-109
• /
• 2000

Elastic dynamic responses analysis program for ship hulls considering slamming impact loads due to the voyage in large amplitude waves is developed. Ship hull structures are modeled by a thin-walled beam model in order to consider effects of shear deformation. The momentum slamming theory is used to derive nonlinear hydrodynamic forces considering intersection between wave particles and ship section. For the validation of the developed computer program, motions of a V-shaped simple section model and S-175 standard container model are calculated and analyzed. In each numerical example, time histories of relative displacement, velocity and vertical bending moment of a ship section are derived, considering the effect of slamming impacts in various wave conditions.ures near the free surface as well as the wake of the hydrofoil.