• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1218-1219
• /
• 2011

본 논문은 KA555 Timer을 이용한 PWM회로로 구성된 아날로그 방식의 DC-DC Buck Converter와 AVR ATmega128를 이용한 PWM회로로 구성된 디지털 방식의 Buck Converter을 설계하여 각각의 특성을 비교 분석하였다. 제안된 컨버터들은 공통적으로 전원을 공급받아 전압분압회로를 통해 DC-DC Buck Converter의 PWM 제어회로부에 공급되며, 아날로그방식 컨버터의 제어부는 KA555 timer을 이용하여 구형파회로와 미분회로를 구성하고, 출력된 삼각파와 정현파를 KA555 timer을 이용하여 PWM파형으로 제어한다. 디지털방식의 컨버터는 AVR RISC 8-bit 마이크로프로세서 ATmega128을 이용하여 PWM 제어부를 구성하고 이를 LCD창을 통해 그 값을 확인할 수 있도록 설계하였다. 본 논문에서는 두 가지 방식의 제어부를 구성하여 제작 및 실험함으로써, 각각의 장단점을 비교하여 시스템 구성시 요구조건인 소형경량, 단가저감, 효율 등을 비교하여 그 상황에 맞는 설계가 가능할 것이다.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.391-392
• /
• 2017

최근 자동차 산업의 연구개발의 핵심화두는 효율성 제고 및 NVH(Noise, Vibration, Harshness) 개선에 있다. 특히나 많은 부품들의 개발에 있어서 운전자의 운전 편의성을 높이는 성능적인 지표 외에도 운전자가 느끼는 소음, 이상 진동에 대한 감성성능에 대한 소비자의요구도 높아지고 있다. 이러한 경향에 맞추어 자동차 각 부분의 소음저감, 효율향상을 고려한 설계에 대한 연구가 활발해지고 있다. 많은 자동차 부품들에 모터가 사용되고 있으며, 특히 차량용 쿨링팬의 경우 모터를 사용하여 차량 운행 시 발행하는 (배터리의 온도를) 적절한 수준으로 유지시켜주거나 친환경 자동자차 배터리를 쿨링 하는 역할을 한다. 대다수의 쿨링팬 모터로 BLDC모터가 많이 사용되며 이는 전통적인 제어 방법인 구형파제어를 사용하고 있다. 본 논문에서는 저전압 배터리의 전원을 사용하여 BLDC 쿨링팬을 안정적으로 구동할 수 있는 제어기를 개발하였고, 소음저감 및 높은 효율을 위하여 정현파로 제어하는 기법을 적용하였다. 개발된 시작품의 성능 시험을 통해 그 결과를 검증하였다.

• 전기의세계
• /
• v.25 no.2
• /
• pp.92-99
• /
• 1976

The dynamic characteristic analysis of AC Servomotor which is controlled by AC square voltage is studied in this paper. Although nonconventional sampling method is proved to be effective in controlling the output by changing square voltage width, it is difficult to attack the problem by the classical method. In order to solve the problem easily, the state transition method is introduced in this paper. One of the important advantages of this approach is that the analysis procedure is of a recursive nature and this can readily be programed on a digital computer to yield a quick, accurate solution. Various output characteristics are identified by changing the square voltage width and much improved output response is obtained when the square voltage widths are modulated for the initial period.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.1
• /
• pp.30-40
• /
• 2002

This paper studies the electronic ballast development for 250w MH lamps. We have improved the input power factor using a PFC IC. To provide the rating voltage required In the lamps, we have used the buck type dc-dc converter By this method, the stress of switching devices in inverter can be reduced. The inverter is the Full-Bridge type. To eliminate the acoustic resonance phenomena of MH lamps, we have added the high frequency sinewave voltage to the low frequency square-wave voltage to the lamp. We hove developed the igniter circuit using the L, C devices. We could control dimming of the lamp by varying the output voltage of the buck converter. The time of illuminating lamps and luminous intensity could be adjusted by season and time band. The buck converter output voltage can be controlled and the no load and over current situation were Protected by the development of the microprocessor Program.

• Journal of Sensor Science and Technology
• /
• v.8 no.6
• /
• pp.427-433
• /
• 1999

In this paper, we have presented an one-axis fluxgate magnetic sensor with ferrite core, excitation, and pick-up coil. This magnetometer is consist of a sensing element, driving circuits for excitation coil and signal processing for detecting second harmonic frequency component which is proportional to the DC magnetic to be measured. The sensor core is excited by a square waveform of voltage through 82 turns of the excitation coil. The second harmonic output of pick-up coil(150 turns) is measured by a FFT spectrum analyzer. This result is compared to output of PSD(phase sensitive detector) unit for detecting a second harmonic component. The measured sensitivity is about 50 V/T at driving frequency of 2 kHz. The nonlinearity of fluxgate magnetic sensor is calculated about 2.0%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.15-22
• /
• 2011

Integrated-optic symmetric/asymmetric Mach-Zehnder interferometers at $1.3{\mu}m$ wavelength were studied as sensing part for electric-field measurement system. The devices were simulated based on the BPM software and fabricated utilizing Ti-diffused $LiNbO_3$ channel optical waveguides and lumped-type electrodes. A half-wave voltage of $V_{\pi}$=6.6V and modulation depth of 100% and 75% for a symmetric structure were measured for 200Hz and 1kHz electrical signal bandwidth, respectively. By the way, almost half-maximum power transmission was observed for asymmetric interferometers with ${\pi}$/2 intrinsic phase difference. Expected experimental measurements were observed for 1kHz electrical signal bandwidth.

• Food Engineering Progress
• /
• v.15 no.4
• /
• pp.398-403
• /
• 2011

A dielectric barrier discharge plasma (DBDP) treatment system was fabricated and the optimum operating conditions for the plasma generation were determined in order to explore the potential of cold plasma as a non-thermal proessing technology. The microbial inactivation performance of the system was also evaluated against Staphyloocus aureus. The system consisted of power supply, transformer, electrode assembly and sample treatment plate. The input power was 220 V single phase AC and amplified to 10.0-50.0 kV on a transformer. A pulsed sine wave of frequency 10.0-50.0 kHz was introduced to the electrode embedded in ceramic as a dielectric barrier material in order to generate plasma at atmospheric pressure. Higher currents and consequently greater power were required for the plasma generation as the frequencies increased. A homogeneous and stable plasma was generated at currents of 1.0-2.0, and frequencies of 32.0-35.3 kHz. The optimum electrode-gaps for the plasma generation were 1.85 mm without loaded samples. More power was consumed as the electrode-gaps increased. The practically optimum electrode- gap was, however, 2.65 mm when samples were treated on slide-glasses for microbial inactivation. The maximum temperature increase after 10 min treatment was less than 20$^{\circ}C$, indicating no microbial inactivation effect by heat and thereby insuring a non-thermal method. The DBDP inactivation effect against Staphyloocus aureus increased linearly with treatment time up to 5 min, but plateaued afterward. More than 5 log reduction was achieved by 10 min treatment at 1.25 A.

• Journal of Biosystems Engineering
• /
• v.7 no.2
• /
• pp.18-29
• /
• 1983

A low cost and versatile data acquisition system for the field and laboratory use was developed by using a single board microcomputer. Data acquisition system based on a Z80 microprocessor was built, tested and modified to obtain the present functional system. The microcomputer developed consists of 6 kB ROM, 5 kB RAM, 6-seven segment LED display, 16-Hex. key and 8 command key board. And it interfaces with an 8 channel, 12 bits A/D converter, a microprinter, EPROM programmer for 2716, and RS232C interface to transfer data between the system and HP3000 mini-computer manufactured by Hewlett Packard Co., A software package was also developed, tested, and modified for the system. This package included drivers for the AID converter, LED display, key board, microprinter, EPROM programmer, and RS232c interface. All of these programs were written in 280 assembler language and converted to machine codes using a cross assembler by HP3000 computer to the system during modifying stage by data transferring unit of this system, then the machine language wrote to the EPROM by this EPROM programmer. The results are summarized as follows: 1. Measuring program developed was able to control the measuring intervals, No. of channels used, and No. of data, where the maximum measuring speed was 58.8 microsec. 2. Calibration of the system was performed with triangle wave generated by a function generator. The results of calibration agreed well to the test results. 3. The measured data was able to be written into EPROM, then the EPROM data was compared with original data. It took only 75 sec. for the developed program to write the data of 2 kB the EPROM. 4. For the slow speed measurements, microprinter instead of EPROM programmer proved to be useful. It took about 15 min. for microprinter to write the data of 2 kB. 5. Modified data transferring unit was very effective in communicating between the system and HP3000 computer. The required time for data transferring was only 1~2 min. 6. By using DC/DC converting devices such as 78-series, 79-series. and TL497 IC, this system was modified to convert the only one input power sources to the various powers. The available power sources of the system was DC 7~25 V and 1.8 A.