• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.9
• /
• pp.886-894
• /
• 2014

A wideband bow-tie antenna fed by wideband microstrip-coplanar stripline(CPS) balun and band notch structures that can be applied to bow-tie antenna are proposed in this paper. In order to increase bandwidth, bow-tie radiators are reshaped so that the surface current flows continuously, and wideband impedance matching is achieved by adjusting strip width and spacing of CPS feeding line. The VSWR is measured as 2:1 over the wide frequency range of 2.3~12 GHz. The fabricated antenna size is $60mm{\times}60mm$. In order to achieve the band-notch function at WLAN(5.8 GHz), ${\lambda}/4$ folded-slits located ${\lambda}/4$ away from feeding point are utilized. To minimize the slit size, folded-slit type is adopted. The measured VSWR is 7:1 and gain attenuation is 14 dB at 5.8 GHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.4
• /
• pp.62-68
• /
• 2010

This work proposes a 10b 100MS/s DAC based on a segmented local matching technique primarily for small chip area. The proposed DAC employing a segmented current-steering structure shows the required high linearity even with the small number of devices and demonstrates a fast settling behavior at resistive loads. The proposed segmented local matching technique reduces the number of current cells to be matched and the size of MOS transistors while a double-cascode topology of current cells achieves a high output impedance even with minimum sized devices. The prototype DAC implemented in a 0.13um CMOS technology occupies a die area of $0.13mm^2$ and drives a $50{\Omega}$ load resistor with a full-scale single output voltage of $1.0V_{p-p}$ at a 3.3V power supply. The measured DNL and INL are within 0.73LSB and 0.76LSB, respectively. The maximum measured SFDR is 58.6dB at a 100MS/s conversion rate.

• Clean Technology
• /
• v.13 no.4
• /
• pp.293-299
• /
• 2007

Direct coating of catalyst layer on the $Nafion^{(R)}$ membrane has been optimized in the process of fabrication of membrane electrode assembly (MEA) to enhance the performance of direct methanol fuel cell (DMFC). In this method, the contact resistance at the interface of the catalyst layer and the membrane was found to be low. The effect of catalyst loading, thickness of membrane and the gas diffusion layer (GDL) with or without the presence of micro-porous layer (MPL) on the performance of the MEA was also investigated. The MEA fabricated by the above-mentioned method exhibited a performance of $147\;mW/cm^2$ and $100\;mW/cm^2$ at $80^{\circ}C$ and $60^{\circ}C$, respectively, with the catalysts loading of $4\;mg/cm^2$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.11
• /
• pp.5879-5884
• /
• 2013

With the rapid industrialization and economical development, the electricity demands of the industrial facilities and densely populated large cities are continuing to increase in Korea. The increase in the power consumption requires the extension of power facilities, but it is difficult to secure spaces for equipment installation in the limited space of urban areas. In addition, the 154 kV or 345 kV transmission systems in Korea has a short transmission distance, and are connected to one another in network structures that ensure the high reliability and stability of power supply. This structure reduces the impedance during the fault in power system, and increases the magnitude of in the short circuit fault current. The superconducting fault current limiter (SFCL) was devised to effectively address these existing problems. The SFCL is a new-concept eco-friendly protective device that ensures fast operation and recovery time for the fault current and does not need additional fault detection devices. Therefore, many studies are being conducted around the world. In this paper, based on the wiring method the initial fault current characteristics, current limiting characteristics, according to the incident angle and the change in inductance current limiting characteristics were analyzed in a multifaceted methods.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.163-163
• /
• 2017

철강재는 대량 생산이 가능하여 경제성이 뛰어나고 기계적 성질도 우수하여 다양한 산업 분야에서 널리 사용되고 있다. 그러나 철강재는 부식 환경에 취약하기 때문에 그 용도에 따라 다양한 내식성을 부여하는 표면처리를 적용하고 있다. 이러한 철강재에 대한 내식성 표면처리로는 용융아연도금(HDG)과 용융알루미늄도금(HDA)이 우수한 내식성과 다양한 특성으로 널리 사용되고 있으며 아연과 알루미늄을 접목시킨 갈바륨(GL)도금 또한 우수한 내식성 코팅으로 알려져 있다. 또한 최근에는 기존 용융아연도금에 알루미늄(Al) 과 마그네슘(Mg)을 첨가한 3원계 도금강판이 개발되어 기존 용융도금강판 대비 고내식 코팅으로 알려져 있으며 그 적용은 점차 확대되고 있는 추세이다. 일반적으로 이와 같은 강판소재의 내식성 평가에 대해서는 실제 사용할 환경에 폭로하여 비교-시험 하는 것이 가장 확실하고 신뢰도가 높은 방법이다. 그러나 이러한 방법은 경우에 따라 수년에서 수십년에 이르는 장시간이 소요된다. 그러므로 이 방법을 대체하기 위한 각종 가속적 부식 시험들이 널리 적용되고 있다. 즉, 그 목적이나 용도에 따라 염수분무(SST), 침지(Immersion) 및 전기화학적 분극(Polarization) 등 실내에서 부식 시험 하는 방법이 사용되고 있다. 한편, 이러한 부식 가속 시험들은 실제 외부에서 폭로 시험한 결과와의 상관성이 불명확한 경우가 많아 종종 해석에 어려움을 갖고 있는 실정이다. 또한 이 시험 방법들은 동일 재료를 시험하더라도 시험방법의 차이에 따라 부식요인이나 해석방법이 다르므로 인해 그 내식성 결과가 다르게 나타날 수 있다. 그 중 시험목적에 따라 전기화학적 분극 또는 임피던스 분광법(EIS)과 건조 및 습윤 등의 부식 환경 인자들을 적용한 복합부식시험(CCT) 방법은 근사한 대안으로 주목받고 있다. 하지만 이들 시험 또한 실제 부식 환경과는 여러 환경 및 요인들이 다르기 때문에 그 시험방법에 따라 목적하는 시험 결과가 상이하게 나타날 수 있어 해석-평가 하기에 종종 곤란을 갖는다. 이에 따라 최근에는 재현성이 우수하고 실제 부식 환경을 유사하게 모사할 수 있는 내식성 시험과 해석-평가에 대한 내용이 주요한 과제로 사료되고 있다. 본 연구에서는 다양한 내식성 코팅 강판소재들에 대하여 염수분무(SST), 복합부식(CCT), 갈바닉 시험, EIS 시험을 통하여 부식시험 종류 및 시험 환경, 코팅 소재 별 부식경향을 비교-분석하고자 하였다. 또한 이들 부식 진행과정에서는 미세구조관찰(SEM), 결정구조 분석(XRD) 및 원소조성 분석(EPMA)을 통해 다양한 조건에 따른 강판소재들의 부식경향을 비교-평가하고, 실제 환경과의 상관성 및 가속관계를 도출하고자 하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.158-165
• /
• 2007

In this paper, the circularly polarized $4{\times}4$ array antenna is proposed for the X-band. A single antenna consists of square patch and unequal cross-aperture coupled feeding. The RHCP(Right Handed Circularly Polarization) is generated by unequal cross-aperture coupled feeding. By reducing space among elements of way antenna from 0.8 ${\lambda}_0$ to 0.45 ${\lambda}_0$, the mounting area of array antenna is miniaturized. The $2{\times}2$ array antenna is designed using sequential rotation feeding network. The good level of gain, axial ratio, and impedance bandwidth are achieved. The $4{\times}4$ array antenna is extended by ${\lambda}/4$ transformer and T-junction power divider. The simulated maximum radiation gain is 15.09 dBi at 10 GHz. The simulated 3 dB Axial Ratio bandwidth is from 9.05 to 10.4 GHz(13.5%). Also the measured impedance bandwidth($VSWR{\leq}2$) of manufactured $4{\times}4$ array antenna is from 8.45 to 11.84 GHz(33.9%). The measured maximum radiation gain is 11.10 dBi at 10 GHz. The measured 3 dB Axial Ratio bandwidth is from 9.42 to 10.47 GHz(10.5%).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.1
• /
• pp.39-46
• /
• 2015

In this paper, a gas sensor using a modified $90^{\circ}$ hybrid coupler structure with conducting polymer which operates at 2.4 GHz is represented. Conducting polymers are used to the gas sensing material in proposed sensors. The conducting polymer varies its electrical property, such as work function and conductivity corresponding to the certain gas. To verify this variation of electrical property of conducting polymer at microwave frequencies, the conducting polymer is incorporated with the $90^{\circ}$ hybrid coupler structure, and this proposed sensor operates as reflection type variable attenuator and variable phase shifter. The conducting polymer is employed as impedence-variable transmission lines that cause a impedance mismatching between the general transmission line and conducting polymer. The experiment was conducted with 100 ppm ethanol gas at temperature of $28^{\circ}C$ and relative humidity of 85 %. As a result, the amplitude deviation of $S_{21}$ is 0.13 dB and the frequency satisfying ${\angle}S_{21}=360^{\circ}$ is shifted about 2.875 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.1
• /
• pp.11-19
• /
• 2013

In this paper, we designed and implemented the planar monopole antenna using the coupling effect for the multi-band characteristic. A parasitic element for the multi-band characteristic based on a rectangular patch with single resonance is inserted. Spiral shaped parasitic element is used for minimizing the antenna size and obtaining the multi-resonance characteristic. The frequency characteristics are modified and optimized by varying specific parameters. By inserting an L-shaped resonator at both sides of the feed line which connected through the via hole to the ground plane, unnecessary frequency bands are eliminated. Proposed antenna dimension is $40{\times}60{\times}1mm^3$. It is fabricated on the FR-4 substrate(${\varepsilon}_r$=4.4) using a microstrip line of $50{\Omega}$ for impedance matching. By measurement results, the characteristic of the return loss under -10 dB are 1.714~2.496 GHz, 2.977~4.301 GHz, and 4.721~6.315 GHz, and the radiation patterns have omni-directional shapes.

• Journal of the Korea Society of Computer and Information
• /
• v.15 no.8
• /
• pp.59-66
• /
• 2010

In this paper, the internal antenna for mobile communication handset which is able to control both coupling coefficient and resonant frequency without any major modification of radiator and ground plane of antenna. Novel internal antenna with its controllable resonant frequency is presented for triple-band or over mobile handsets. The operating range can include GSM(880~960 MHz), GPS($1,575{\pm}10MHz$), DCS(1,710~1,880MHz), US-PCS(1,850~1,990 MHz), and W-CDMA(1,920~2,170 MHz). The proposed antenna is realized by combination of a half wavelength loaded line antenna and PIFA(Planner Inverted F Antenna). A single shorting and feeding points are used and they are common to both antenna structures. One of two inductors which is placed at each shorting post, one inductor is for adjusts amount of coupling, and the other controlling the resonant frequency in DCS/US-PCS/WCDMA bands. The inductance range for control of input impedance is between 0nH and 6.8nH, and each of gain variation in GSM, GPS and DCS/US-PCS/WCDMA band is under 0.15dBi, 0.73dBi and 0.29dBi. The inductance range for control of the resonant frequency is between 1640MHz and 2500MHz, and each of gain variation in GSM, GPS and DCS/US-PCS/WCDMA band is under 0.46dBi, 0.53dBi and 0.8dBi.

• Clean Technology
• /
• v.22 no.4
• /
• pp.308-315
• /
• 2016

$SiO_x/ZnO$ composites were prepared from sol-gel method for excellent cycle life characteristics. The composites were coated by PVC as a carbon precursor. ZnO removal to create a void space therein was able to buffer the volume change during charge and discharge. To determine the crystal structure and the shape of the synthesized composite, XRD, SEM, TEM analysis was performed. The carbon contents in the composites were confirmed by TGA. The pore structure and pore size distribution of the composite was measured with the BET specific surface area analysis and BJH pore size distribution. Enhanced electric conductivity by carbon addition was determined from powder resistance measurement. Electrochemical properties were measured with the AC impedance and the charge and discharge cycle life characteristics. When carbon was coated on the $SiO_x/ZnO$ sample, the electrical conductivity and the discharge capacity were increased. After removal of ZnO with HCl the surface area of the sample was increased, but the discharge capacity was decreased. $SiO_x/ZnO$ sample without acarbon coating showed very low discharge capacity, and after carbon coating the sample showed high discharge capacity. For cycle life characteristics, $C-SiO_x/ZnO$ composite (Zn : Si : C = 1 : 1 : 8) with a capacity of $815mAh\;g^{-1}$ at 50 cycle and 0.2 C has higher capacity than existing graphite-based anode materials.