• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.10-13
• /
• 2011

내진설계의 기본 개념은 보를 기둥보다 약하게 설계하여 보에 소성힌지를 발생시켜 구조물 전체의 큰 변형을 방지하는 것이다. ACI 352R-02에서는 지역의 지진특성에 따라서 접합부의 상세 설계법을 구분하여 적용한다. 하지만 보와 접합부의 내력 차이가 상대적으로 작게 설계된 구조물의 경우 탄성 범위를 유지해야 하는 경우의 접합부에도 파괴가 발생할 가능성이 있다. 횡하중이 작용할 때 접합부 내부는 전단력의 지배를 받게 되고, 전단내력과 부착내력에 따라서 파괴모드가 결정된다. 본 논문에서는 양방향 반복하중이 작용하는 10개의 보-기둥 접합부를 통해서 접합부와 인접보의 전단내력 차이에 따라서 발생하는 파괴모드를 관찰하고 접합부 내의 전단내력 및 부착내력의 감소로 인해 발생하는 부재의 연성에 대해서 관찰하였다.

• Computational Structural Engineering
• /
• v.5 no.2
• /
• pp.119-127
• /
• 1992

The entire nonlinear behavior of reinforced concrete frames up to collapse, is analyzed by the displacement control method and the combined layered and nonlayered method. All of the rigidities of section are calculated approximately by a sum over all the layers for the layered method, are used the integral values over the cross section area for the nonlayered method. The spurious sensitivity to the chosen element size in the result of analysis by finite element method for the materials with strain-softening can be overcome by modifying the strain distribution based on the concept of fracture energy at plastic hinge considering the applied axial load.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2003.05a
• /
• pp.360-365
• /
• 2003

최근 선진국에서 차세대전투기와 고속철도차량 및 자동차 동체 등 경량화를 위해 복합재료의 사용범위가 증가되고 있다. 특히 강화재로서 섬유를 직물구조의 형태를 이용한 직물구조 CFRP 복합재료는 일방향 섬유에 비해 변형능력이나 기계적 특성이 우수하여 철근 콘크리트 구조물의 보강제와 같은 구조물 등에까지 그 사용이 확대되고 있다. 하지만 직물구조 CFRP 복합재료는 내부의 손상형태나 위치를 파악하기가 어렵고 직물구조의 복잡한 강화구조를 가지기 때문에 그 역학적 손상거동과 명확한 파괴거동 해석수법은 확립되어 있지 않다.(중략)

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2018.05a
• /
• pp.65-66
• /
• 2018

국내 항만의 건설 및 확장 보수를 위한 설계 단계에서의 평면배치 검토시 항내측으로 내습하는 파랑변형특성에 대한 정밀한 평가는 필수적이다. 이에 따라 많은 수학적 모델들이 연안역과 항만에서의 파랑전파와 변형에 대해 개발되어 왔다. 특히 항내정온도의 해석은 항만 사용성 측면에서 매우 중요하며 실제 해상의 파랑상태와 유사한 불규칙파로의 해석이 요구되어 지고 있다. 항내정온도 해석에 있어서 항내파랑장 형성에 크게 영향을 미치는 구조물의 반사율을 효과적으로 적용하는 것은 매우 중요하다. 하지만, 구조물의 반사율은 이론계산이 어렵고, 일반적으로는 모형실험 혹은 현지관측에 의해 추정된다. 따라서, 일반적인 경우 비용 및 시간상의 제약으로 인해 평면 파랑모형으로 정온도 해석시 반사율의 적용은 구조형식별로 연구자들에 의해 개략 제시된 반사율을 적용하고 있다. 특히, 다방향 불규칙파의 적용시에 경계조건으로는 다방향 불규칙파를 효과적으로 제어할 수 있는 부분반사 경계면과 계산영역 밖으로 나가는 파랑에 대해서 인공적인 흡수층 또는 감쇠층(artificial damping layer)을 설정하여 반사를 제어하는 기법을 많이 적용하고 있다. 이때 항만구조물의 부분반사는 파랑제원에 따른 damping layer의 parameter의 조정에 의해 구조물의 구조형식별 반사율을 적절히 재현할 필요성이 있다. 본 연구에서는 불규칙파를 대상으로 damping layer의 parameter(무차원 감쇠계수, 감쇠층의 두께)등의 변화에 따른 반사율의 변화특성을 고찰하고, 향후 부분반사 경계면으로 damping layer가 적용되는 평면 파랑모형의 정온도 해석시 부분반사의 적용에 대한 기초자료를 제공하고자 한다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.460-465
• /
• 2016

Long pipe structures are usually installed in fixtures located with regular intervals or laid underground. Therefore, deflection and deformation could easily occur due to their weight or ground activity. A shape monitoring technique can be used effectively to evaluate the integrity of the pipe structures. Fiber Bragg grating (FBG) sensors, which have an advantage of multiplexing could be used to measure strains at multiple-points of a long structure. In this study, to evaluate the integrity of a pipeline, a shape estimation technique based on strain information was proposed. Furthermore, different experiments were conducted to verify the performance of the proposed technique. Thus, the proposed shape estimation technique can represent the shape according to the deformation of the specimen using the FBGs. Moreover, calculated deflection of the pipeline using the estimation technique showed a good agreement with the actual deflection of the pipeline.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.1 no.1
• /
• pp.22-30
• /
• 1989

Wave propagation is changed by the effect of shoaling, current-depth refraction and shelter-ing etc. To solve these problems. numerous models have been developed. In the present study, a coordinate system is proposed based on the wave ray equation with the wave number equation including diffraction effects . The governing equation for the study was derived from the mild slope wave equation in non-steady state, including current effects (Kirby, 1986a) and trans-formed into an orthogonal curvilinear coordinate system on the basis of the wave ray equation. To obtain a numerical solution, an explicit finite difference scheme was used, and solved by the relaxation method. This model was tested for various cases: Firstly a submersed circular shoal and a constant unit depth. Secondly a submerged elliptic shoal on a slope, and finally a breakwater harbour with obliquely incident waves on a slope. The model was found to simulate the experimental results and other theoretical results in wave height and wave angle fairy well, and the applicability of the model around an arbitrary shaped coastal structure was also verified. To demonstrate the general usefullness of the present approach , the model is to be applied to a field situation with a complex bed topography.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.5 s.57
• /
• pp.93-100
• /
• 2009

This study presents reasonable relationships to estimate the deformation based on beam mechanism analysis and TDR(Time Domain Reflectometry) data. To declar the length points of co-axial cable installed in civil structure, Nano material ($BaTiO_3$ powders and silver mixture) is used on co-axial cables. From the laboratory test, nano material could make the correct information about attached cable points on beam, and TDR sensor system and Fourier series (data filter) found out the deformation of beam. Therefore it is concluded that the correct deformed information of beam were acquired by Nano-TDR and Fourier filter, they are much more effective to apply at health monitoring system in civil structure compared to conventional TDR or Fiber Optic Sensor (FOS) systems.

• Journal of Korean Association for Spatial Structures
• /
• v.5 no.4 s.18
• /
• pp.53-59
• /
• 2005

This paper provides the results of the investigation on the optimum thickness distribution of plate structures with different essential boundary conditions. In this study, the strain energy to be minimized is considered as the objective function and the initial volume of structures is used as the constraint function. The computer-aided geometric design (CAGD) such as Coon's patch representation is used to represent the thickness distribution of plates. A reliable degenerated shell finite element is adopted to calculate the accurate strain energy level of the plates. Robust optimization algorithms provided in the optimizer DOT are adopted to search the optimum thickness values during the optimization iteration. Finally, the square plate is used to find out the optimum thickness distribution of plates according to different essential boundary condition.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.18 no.3
• /
• pp.321-332
• /
• 2005

In this paper, the time-domain finite element formulations for axisymmetric linear viscoelastic problems, especially for the viscoelastic hollow sphere and cylinder, under various boundary conditions are presented with the theoretical solutions of them obtained by using the elastic-viscoelastic correspondence principle. It is assumed that the viscoelastic material behaves like a standard linear solid in distortion and elastically in dilatation. Numerical examples are solved based on the spherically symmetric, axisymmetric and plane strain finite element models. Good agreements are obtained between numerical and theoretical solutions, which shows the validity and accuracy of the presented method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.2
• /
• pp.52-58
• /
• 2002

Measurment of dynamic strain is important to monitor structural integrity. In this paper, the new type of EFPI is proposed to measure the dynamic strain. The second reflecting surface of fiber in this new sensor is deposited gold on to increase its reflectivity. So, it is called the gold-deposited EFPI (G-EFPI) in this paper. In order to explain the principle of measurement of the dynamic strain, two models for the loss of intensity are proposed and an experiment is performed. If a cavity between two reflecting surface increases, the loss of the light that passes through the cavity increases, causing a subsequent decrease in the output intensity of the sensor. Conversely, if the cavity decreases, the amount of loss decreases and the output intensity increases. Also the optimal length of the cavity is proposed to manufacture the G-EFPI with high sensitivity. Finally, the dynamic strainof a composite specimen was measured successfully using the G-EFPI.