• Korean Journal of Heritage: History & Science
• /
• v.53 no.2
• /
• pp.64-87
• /
• 2020

Copper trihydroxychloride (atacamite, botallackite, paratacamite, etc.), the first green pigment used in Mogao Grotto's mural paintings of China, has been known as "copper green", "green salt", and "salt green", etc. and has been used as an important green pigment with malachite. At first, the natural mineral atacamite was employed, but after the Five Dynasties (907~960 CE), synthetic copper trihydroxychloride was primarily used. In Chinese literature, copper green, green salt, and salt green are recorded as being made via reaction with copper powder, Gwangmyeongyeom (natural sodium chloride), and Yosa (natural ammonium chloride), and the prepared material was analyzed to be copper trihydroxychloride. Copper trihydroxychloride pigment was not found in paintings prior to the Joseon Dynasty (1392~1910 CE) in Korea. In analysis of the green pigments used in paintings and the architectural paintworks in the Joseon Dynasty, copper trihydroxychloride was also shown to have been used as an important green pigment with malachite (Seokrok). In particular, the proportion of copper trihydroxychloride use was high in Buddhist paintings, shamanic paintings, and dancheongs (decorative coloring on wooden buildings). Some of these turned out to be synthetic copper trihydroxychloride, but it is unclear whether the rest of them are synthetic or natural pigments due to a lack of analyzed data. From literature and painting analyses, the pigment name of copper trihydroxychloride in the Joseon Dynasty turns out to be Hayeob, a dark green pigment. It is believed to have first been prepared by learning from China in the early Joseon period (early 15^th century) and its use continued until the late 19^th century with imported Chinese pigment. Round or oval particles with a dark core of copper trihydroxychloride which were used in Chinese literature were similar to the synthetic copper trihydroxychloride pigments used in the Joseon Dynasty and Chinese paintings. Therefore, the synthetic copper trihydroxychloride pigments of Korea and China are believed to have been prepared in a similar way.

• Journal of the Korean Chemical Society
• /
• v.30 no.5
• /
• pp.415-422
• /
• 1986

The metal-support interaction of copper oxide supported on ${\gamma}$-alumina and silica was studied by X-ray diffraction (XRD) and temperature-programmed reduction(TPR). It was found that XRD pattern of CuO can not be observed up to 5.0wt % copper content for CuO/${\gamma}-Al_2O_3$ while CuO/$SiO_2$ sample shows the CuO pattern even at 2.5wt% copper content. $H_2-$TPR of CuO/${\gamma}-Al_2O_3$ system shows four major peaks at 145${\circ}C$, 185${\circ}C$, 210${\circ}C$, and 250${\circ}C$. In the case of CuO/$SiO_2$, a large peak at 250${\circ}C$ was appeared accompanying a small peak at 425${\circ}C$. Comparing the TPR peaks with that of copper aluminate which was prepared from the calcination of CuO/${\gamma}-Al_2O_3$ at 1000${\circ}C$, the peaks at around 145${\circ}C$, 200${\circ}C$ (185${\circ}C$ and 210${\circ}C$), and 250${\circ}C$ were corresponded to $Cu^+$ ion in CuO interacting ${\gamma}-Al_2O_3$, $Cu^+$ ions in defect sites of ${\gamma}-Al_2O_3$ and $Cu^{2+}$ ion in the bulk CuO layer, respectively. From the results, it was concluded that there is considerable metal-support interaction in CuO on ${\gamma}-Al_2O_3$ and the interaction results in a stabilization of $Cu^+$ ion in the system.

• Korean Journal of Heritage: History & Science
• /
• v.56 no.2
• /
• pp.148-169
• /
• 2023

Hayeob pigment is known as one of the traditional dark green pigments, but the color, raw material, and manufacturing method have not been clearly identified. However, comparing the analysis results of the particle shape and constituent minerals of Hayeob pigments revealed through pigment analysis studies of colored cultural properties such as Dancheong, Gwaebul, and paintings, Hayeob pigments appear to be the same as Dongrok pigments produced by salt corrosion. Therefore, in order to restore Hayeob pigment, the manufacturing method of Dongrok pigment was studied based on the records of old literature. The Dongrok pigment manufacturing method confirmed in the old literature records is a natural corrosion method in which copper powder and a caustic are mixed and then left in a humid condition to corrode. Based on this, artificial corrosion using a corrosion tester was adopted to corrode the copper powder more efficiently, and an appropriate mixing ratio was selected by analyzing the state of corrosion products according to the mixing ratio of the caustic agent. In addition, the manufacturing method of Dongrok pigment was established by adding a salt removal process to remove residual caustic agents and a purification process to increase chroma during pigment coloring. The prepared Dongrok pigments have a bluish green or green color, show an elliptical particle shape and a form in which small particles are aggregated, and a porous surface is observed. The main constituent elements are copper(Cu) and chlorine(Cl), and the main constituent mineral is identified as atacamite [Cu₂Cl(OH)₃]. As a result of an accelerated weathering test to evaluate the stability of the prepared Dongrok pigments, it was found that the greenness partially decreased and the yellowness significantly increased as deterioration progressed. Before deterioration, the Dongrok pigments had lower yellowness compared to the Hayeob pigments of the old Dancheong, but after deterioration, yellowness increased significantly, and it was found to have a similar chromaticity range as Dancheong's Hayeob pigments. As a result, the prepared Dongrok pigments were confirmed to be similar to Dancheong's Hayeob pigments in terms of color as well as particle shape and constituent minerals.

• Proceedings of the Mineralogical Society of Korea Conference
• /
• 2001.06a
• /
• pp.58-59
• /
• 2001

부산에서 북동쪽으로 대략 25km 떨어진 지점에 위치하고 있는 일광광산 부근의 지질은 백악기 화산암ㆍ퇴적암 그리고 이를 관입한 화강암류와 이 암주 내에 발달하는 구리-중석을 함유하고 있는 각력파이프광상으로 이루어져 있다. 일광광산의 화강암류는 거의 타원형으로 felsic한 중앙부와 mafic한 양상의 주변부로 나뉘어지며, 암주 내에 수직적인 원통형의 각력파이프가 광화대를 이루고 있고, 그 주변에는 모암변질대가 발달되어 있다. 각력파이프를 충진하고 있는 vein과 화강암의 중앙부에는 전기석이 풍부하게 산출되고 있다. 일광광산에서 산출되는 전기석은 야외 관찰시 각력파이프 중심에서부터 외곽부쪽으로 전기석의 풍부함이 감소하며 산출형태도 달라진다. 파이프에서 대략반경 150m내에서 전기석은 침상형 의 방사상 모양 내지 rosettes형으로 풍부하게 산출되며, 화강암내의 mafic한 암편을 치환한 형태로 산출되기도 한다. 암주의 중앙부 주변부에서는 거의 미세한 구상형으로 산재되어 나타나고 있다. 전기석은 복잡한 화학식 {(Na, Ca)(Fe, Mg)$_3$(Al, Li)$_{6}$(BO$_3$)$_3$Si$_{6}$O$_{18}$ (OH, F)$_4$}을 갖는 붕산 규산염광물이다. 이러 한 다양한 성분은 마그마의 진화과정, 모암의 특성, 온도, 압력, 성분과 같은 물리ㆍ화학적 성질에 따라 전기석의 성분이 체계적으로 변하기 때문에 모암과 전기석 기원과의 상관관계를 파악할 수 있다. 파이프 부근의 화강암류는 현미 경상에서 전기석이 석류석과 같이 풍부하게 나타나며 장석들은 변질받은 상태로 세리사이트, 녹렴석으로 나타나고, 흑운모와 각섬석은 녹니석화되어 변질된 상태를 보이고 있다. 파이프 중심에서 외곽부로 갈수록 전기석의 함량은 줄어들고 있고 장석들이 알바이트ㆍ칼스베드 쌍정을 보이며, 흑운모가 각섬석보다는 우세하게 나타나고 있다. 전기석은 주상 결정, 자형 내지 반자형의 입자로 다색성을 보이며, 결정 중심에서 가장자리로 갈수록 파란색과 황갈색의 광학적 누대구조를 관찰할 수 있다. 일광광산에서 산출되는 전기석에 대한 현미경 관찰은 열수기원임을 지시하고 있다. 야외조사와 현미경 관찰의 예비조사에 의하면 일광광산의 전기석이 형성된 환경은 다른2가지 화학적인 저장소의 혼합 효과의 결과로 생성되어진 것으로 예상된다. 일광의 화강암류를 만든 마그마는 전기석을 형성할 만큼의 Fe-Mg성분이 충분하지 않았을 것이다. 화강암 내에 흑운모와 각섬석의 결정작용에 의해 마그마의 Fe-Mg성분이 고갈되어지고 이로 인해 그 함량이 감소하며 상대적으로 마그마 내에 남은 붕소(B$_2$O$_3$)는 열수로 용리되고 흑운모, 각섬석과 평형을 유지하며 열수에 남아있게 된다. 잔류용융체에 남은 붕소의 함량은 전기석을 만들기에 충분함에도 불구하고, Fe-Mg 함량이 부족하여 마그마 기원의 전기석 결정을 만들 수가 없다가 광맥이 형성된 시기에 또 다른 열수가 공급되면서 이전의 평형이 깨지고 기존의 흑운모와 같은 염기성 광물이 붕소(B)를 함유한 새로운 열수와 반응하여 전기석을 형성한 것으로 예상한다. 앞으로 전암과 광물에 대해 지화학적 연구를 통해 화강암류와 전기석과의 지화학적 연관성, 주성분 원소와 열수의 특성과의 상관관계, 전기석의 기원(마그마 기원인지 열수기원인지)이 보다 정확하게 파악될 것이다. 마그마 진화에 따른 전기석의 성분변화와 기원을 이용하여 일광광산의 동광화대를 형성한 마그마 계에서 열수계로 이어지는 지질학적 과정을 이해할 수 있을 것이며, 암석 성인론적 지시자로서 어떠한 중요성을 갖는지 논의되어질 수 있다.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.2
• /
• pp.97-104
• /
• 2016

In the preparation of Ag-coated Cu flakes using L-ascorbic acid as a reductant for the electroless Ag plating, the effects of pretreatment methods and the reductant concentration on the uniformity of Ag coating layer and the anti-oxidation property of Ag-coated Cu flakes during the heating in air were evaluated. It was found that the removal degree of surface oxide layer during the pretreatment has great influence on the uniformity of Ag coating layer and the formation degree of hole defects in the flakes has slight effect on the anti-oxidation property of Ag-coated Cu flakes. It was also verified that the reductant concentration has great influence on the coverage uniformity and thickness of Ag coating, thus it was could be considered a main process parameter. When the reductant concentration was 0.04 M, high-quality Ag-coated Cu flakes was obtained. When the concentration increased to 0.06 M, however, the anti-oxidation property of Ag-coated Cu flakes became remarkably worse owing to remnant of Cu surface non-coated with Ag by the formation of pure Ag fine particles.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.11
• /
• pp.35-43
• /
• 2016

In this study, by using a Effective Microorganisms Brewing Cycle, it confirmed the purification effect of pollutants that are adsorbed on the basins stench removal and retarding soil. On the basis of on-site application test, a soil decontamination system will be suggested. Using a Effective Microorganisms Brewing Cycle, the odor concentration is reduced 2.5 times than that of natural purification treatment method. It was measured and found that the quality of the pore water discharged from the soil is improved. In addition, it was found that a composite of copper and lead with the fermentation microorganisms adsorbed on soil particles from the surface of the stirred experiments lagoon mixed soil is reduced to 65% and 66%, respectively, The TPH organic component was confirmed that the reduction effect of 85%. Restoration of reservoir contaminated soils using the effective microorganism brewing cycle needs to be more developed and implemented as a long-term purification system. This study may be a good reference of developing more complete microorganism brewing system which will efficiently reduce the odor and soil contamination based on optimal stirring and mixing ratio of the compound solutions and contaminated soils in reservoir.

• Korean Journal of Environmental Agriculture
• /
• v.17 no.3
• /
• pp.200-204
• /
• 1998

Physical and chemical properties of artificial soil produced by firing process were analyzed and compared with normal dry field soil and soil quality standards. Material used for production was water and wastewater treatment sludge, chabizite, and lime. The mixed material was thermally treated in the firing kiln at about $300^{\circ}C$ and $1,000^{\circ}C$, respectively, as per designed process. General properties of the artificial soil were classified as sand by unified soil classification method and similar to the dry-field soil, and even soil conditioning effect were expected when it is mixed properly with normal soil. The artificial soil is high in pH and permeability compared to the dry-field soil. Heavy metal concentrations of the artificial soil met the soil quality standards for the farmland. Overall, the artificial soil was thought to be an appropriate soil which can be returned safely to the nature without significant adverse effect. The cost for the artificial soil production process needs to be lowered for practical application as a sludge treatment, therefore, commercializing of the artificial soil is under review.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.1
• /
• pp.17-21
• /
• 2011

Copper (Cu) had been attractive material due to its superior properties comparing to other metals such as aluminum or tungsten and considered as the best metal which can replace them as an interconnect metal in integrated circuits. CMP (Chemical Mechanical Polishing) technology enabled the production of excellent local and global planarization of microelectronic materials, which allow high resolution of photolithography process. Cu CMP is a complex removal process performed by chemical reaction and mechanical abrasion, which can make defects of its own such as a scratch, particle and dishing. The abrasive particles remain on the Cu surface, and become contaminations to make device yield and performance deteriorate. To remove the particle, buffing cleaning method used in post-CMP cleaning and buffing is the one of the most effective physical cleaning process. AE(Acoustic Emission) sensor was used to detect dynamic friction during the buffing process. When polishing is started, the sensor starts to be loaded and produces an electrical charge that is directly proportional to the applied force. Cleaning efficiency of Cu surface were measured by FE-SEM and AFM during the buffing process. The experimental result showed that particles removed with buffing process, it is possible to detect the particle removal efficiency through obtained signal by the AE sensor.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.5
• /
• pp.449-470
• /
• 2018

A review of research trends on wood surface protection for exterior use obtained the following conclusions: It has been reported that inorganic compounds such as chrome and copper used as wood preservatives can protect wood from weathering. It has been shown that precoating with hydrophobic substances such as wax and oil, UV absorbers, and HALS (Hindered Amine Light Stabilizers) enhances weathering resistance on the surface of ACQ-treated wood. Opaque coatings of paint/stains and semitransparent stains on the surface of preservative treated wood can increase the synergistic effects on prevention of weathering deterioration. Also the need for repainting periodically for the protection of the preservative treated wood surface has also been suggested. ZnO or $TiO_2$ of fine particles, metal ions such as Co, Cr, Fe, Mn, Ni and Ti, and UV absorbers such as tris-resorcinol triazine derivatives, triazine and benzotriazole were introduced as additives for preventing UV in the transparent coating on wood. Several reports showed that chemical modification such as methylation, acetylation, or alkylations have made some increases the effects of preventing weathering with the increasing weight gain of chemical formulas. In heat-treated wood, there were various contradictory reports on the resistance of weathering, and there were some other reports emphasizing the necessity of painting with UV resistance, which leads to the necessity of more advanced studies.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.17 no.4
• /
• pp.257-267
• /
• 2014

The distributions of trace metals in the East Sea were investigated during the R/V Lavrentyev cruise (July 2009) in which four transects from Russia shore to South were conducted to collect 25 surface water samples. The total dissolved concentrations of Cu and Ni were measured using ICP-MS, DRC-e. In the coastal area, their concentrations of Russia shore (Cu, 1.51; Ni, 1.82 nM) were 1.9 times for Cu and 2.0 times for Ni lower than Korea shore (Cu, 2.87; Ni, 3.71 nM). In the subregion, their concentrations of Warm region (Cu, 3.03; Ni, 2.28 nM) were higher for Cu than Cold region (Cu, 2.04; Ni, 2.28 nM). The distributions of Cu and Ni concentrations were divided by lowest level at $10^{\circ}C$ of water temperature. In this study period, the surface water temperatures of Russia shore and Japan basin were lower than $10^{\circ}C$ and them of Ulleung basin and Sakhalin shore were higher. Below $10^{\circ}C$, Cu and Ni concentrations increased when surface water temperatures decreased. Above $10^{\circ}C$, their concentrations increased with temperature, which showed highest concentrations in the Ulleung basin, directly influenced by flux from East Korean Warm Current. By comparing with other sea areas (Western Mediterranean, Atlantic), Cu concentrations in the East Sea were a little higher and Ni concentrations were lower. Particularly as the level of Cu in the offshore in the Ulleung basin were higher than in the coastal area, We can suggest that the atmospheric flux of Cu is relatively important in this area.