• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.4
• /
• pp.319-326
• /
• 2010

The power supply devices for reducing the size of the LCD TV are increasingly required for high efficiency and highe power density. Recently, the LED backlight of the LCD TV comes into the spotlight for LCD TV, because the conventional CCFL backlight has difficult to use constantly according to the mercury restrictions. And In this paper, the LLC resonant converter using the planar transformer for slim-type LED backlight of LCD TV is presented and verified through an experimental prototype for 47 inch LCD TVs with LED backlight system.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2149-2151
• /
• 2003

본 논문에서는 마이컴(PIC16C74)과 Tabu 탐색법 및 지능기법(퍼지 및 신경회로망)을 이용하여 고정밀 제어 및 강인한 제어 성능을 가지는 초소형 DC 모터용 지능형 제어기를 개발하였다. 이를 위해 마이컴(PIC16C74)를 이용한 지능형 제어 알고리즘을 개발하고, 초소형 DC 모터용 드라이브 회로 설계 및 제작하였다. 개발한 초소형 DC 모터 지능형 제어기는 디지털 자동 용접캐리지에 적용할 예정이며, 다른 응용 분야로써는 자동배수장치, 반도체 분야, 산업용 로봇 분야 및 조립자동화 시스템 분야 등에 사용되는 구동모터에 적용함으로서 정밀도와 외부의 잡음에 대한 영향을 경감시켜 안정성과 효율향상 및 에너지절약이 가능할 것이다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.10
• /
• pp.1426-1431
• /
• 2015

Piezoelectric pump can be considered as R-C load and it needs something special driver because the output voltage does not become 0 even though the applied voltage is 0 with common converter. This operating system consists of fly-back converter to increase the input voltage and energy recovery inverter to apply square voltage to the piezoelectric pump. The energy recovery inverter can charge and discharge the energy of capacitive load. In this paper, to enhance performance of the driver, a few elements or circuits are added and modified. To drive the inverter safely, current limit resister is added and adjusted the value to valance the charging and discharging current. In addition, a current limit inductor is added to the input side to limit the input current and enhance the efficiency. Inductor only may make oscillation and another resister is added parallel to the inductor to solve this problem. The converter and inveter are assembled to one board for compactness. The appropriateness is proved with simulation and experiments.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.92-94
• /
• 2019

양방향 스위치를 가지는 Bridgeless PFC 컨버터(BBPFC)는 구조상 복잡한 플로팅 게이트 드라이버를 활용함에도 불구하고 좋은 공통모드 잡음 즉, Common-Mode (CM) 노이즈 특성과 간단한 제어 방법으로 인해 많은 브리지리스 PFC 컨버터 중에서도 고전력 응용분야에서 매우 매력적인 토폴로지이다. 이러한 BBPFC는 도통 경로 상에 위치한 정류 다이오드의 역회복 특성의 상대적인 편차를 활용하여 전력 밀도를 감소시키지 않고도 좋은 공통모드 (CM) 노이즈 특성의 확보가 가능하다. 하지만 이러한 장점을 가지는 BBPFC 구조를 고전력 서버용 전원장치분야에서 활용할 경우, 이미 등록된 특허로 인해 매우 높은 개런티를 지불해야 하므로 그 활용이 매우 제한적이다. 따라서, 본 논문에서는 이미 등록된 특허를 회피하고, 동시에 기존 BBPFC 회로가 가지는 단점인 플로팅 게이트 드라이버를 활용하는 단점을 개선하는 새로운 형태의 브리지리스 PFC 컨버터를 제안한다. 제안된 컨버터는 기존 BBPFC가 가지는 장점인 좋은 (CM) 노이즈 특성을 가지며, 동시에 높은 효율을 달성 할 수 있다. 또한 제안된 컨버터의 경우, 복잡한 플로팅 형태의 게이트 드라이버 회로가 아닌 간단한 부트스트랩 회로를 활용하여 회로를 운용할 수 있다. 더불어 제안된 컨버터는 입력의 양과 음의 주기에서 단 하나의 스위치를 사용하여 회로를 구동할 수 있기 때문에 기존회로 대비 적은 손실을 가져 높은 효율의 획득이 가능하다. 본 논문에서는 제안된 구조에 대해 하이라인 $230V_{RMS}$ 입력과 800W / 400V 출력의 조건을 적용하여 제안하는 구조의 효용성을 검증하고자 한다.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.233-235
• /
• 2020

본 논문은 40 kV 나노초 펄스발생을 위한 모듈형 solid-state Marx modulator(SSMM) 설계에 대해 기술한다. 가속기 및 플라즈마 어플리케이션과 같은 다양한 응용분야에 요구되는 전압 및 전류 사양을 만족시키기 위해 10 kV(출력 전압), 50 ns(펄스폭), 20 ns(상승&하강 시간), 100 kHz(반복률)의 사양을 만족하는 단위모듈기반으로 모듈형 설계를 제안한다. 독립적인 제어가 가능한 4개의 단위모듈을 기반으로 제안된 SSMM은 임의의 출력 파워 및 임피던스를 만족시킬 수 있는 장점을 가지고 있다. 예를 들어, 모든 단위모듈의 위상을 같게 했을 때 출력전압을 증가시킬 수 있으며 각 모듈의 위상을 지연하였을 경우는 펄스의 반복률을 크게 높일 수 있다. 개발된 SSMM은 직렬 스택 MOSFET의 스위칭 성능을 향상시키기 위해 게이트 구동 회로는 동기 신호와 구동 전력을 제공하는 1 턴 변압기로 설계되었다. 출력 펄스의 폭과 하강시간을 최소화하기 위해 다이오드 대신 기생 커패시턴스에 저장된 에너지를 빠르게 방출하는 액티브 풀다운 회로가 적용되었다. 또한, 출력 펄스의 빠른 상승을 달성하기 위해 게이트의 라인 인덕턴스를 최소화하고 모든 게이트 신호의 동기화는 필수적이다. 개발된 ns급 펄스전원장치는 단위모듈을 기반으로 최대 펄스전압이 40 kV 까지 출력이 가능하며 이에 대한 상세설계 및 구현은 실험결과를 바탕으로 검증한다.

• Journal of the Korea Society of Computer and Information
• /
• v.28 no.12
• /
• pp.97-104
• /
• 2023

In this paper, we propose a harmful bird repellent system using directional speakers. Existing sound systems for the extermination of harmful birds have the disadvantage of reducing effectiveness due to the learning effect of birds due to problems caused by noise pollution and monotonous sounds. In this paper, directional speakers are used to minimize surrounding noise. In addition, the up-down and left-right angles of the speaker driving device were freely adjusted to maximize usability. Additionally, the problem of performance degradation due to learning effects was solved by using various scanning patterns. In the future, we plan to develop a platform capable of central control by applying remote control functions and a deep learning model that can recognize bird species.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.1
• /
• pp.61-69
• /
• 2015

The objective of this study is to experimentally investigate the mixed flow behaviors and oxygen transfer characteristics of a vertical orifice ejector. The experimental apparatus consisted of an electric motor-pump, an orifice ejector, a circulation water tank, an air compressor, a high speed camera unit and control or measurement accessories. The mass ratio was calculated using the measured primary flow rate and suction air flow rate with experimental parameters. The visualization images of vertically injected mixed jet issuing from the orifice ejector were qualitatively analyzed. The volumetric oxygen transfer coefficient was calculated using the measured dissolved oxygen concentration. At a constant primary flow rate, the mass ratio and oxygen transfer coefficient increase with the air pressure of compressor. At a constant air pressure of the compressor, the mass ratio decreases and the oxygen transfer coefficient increases as the primary flow rate increases. The residence time and dispersion of fine air bubbles and the penetration of mixed flow were found to be important parameters for the oxygen transfer rate owing to the contact area and time of two phases.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.1
• /
• pp.52-58
• /
• 2018

A Study on the dynamic characteristics of a rotor driven by a tipjet system in hovering condition was carried out. The sectional modeling was performed for the tipjet blade in which the flow path was inserted, and the dynamic characteristics analysis was conducted by modeling the components of the proposed rotor system. The analysis was conducted with respect to the rotational speed and the collective pitch. As a result of the analysis, it was checked that the proposed tipjet rotor did not have aeroelastic instability within the designed operating range. The tipjet test equipment was constructed in order to verify the analysis approach. It was confirmed that the proposed rotor was driven normally by tipjet. The non-rotating eigenmode measurement test and the rotation test were performed, and the validity was proved by comparing the test results and the analysis results.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.8
• /
• pp.174-181
• /
• 2001

Nowadays, the improvement and development of Multi-media and information & communication technology is rapidly processed. They need large data storage capacity. So that, many studies and researches in data storage have been carried out. According to them, the data storage capacity has been increased. But the limitation of storage capacity is happened for several problems. One of them is spot & pit size in optical and magnetic data storage and another is the resolution of actuators. The problems in spot & pit size are covered by new data storage methods-- for examples, AFM(Atomic Force Microscopy), MO(Magneto-optical) system, and NFR(Near-Field decoding) system etc. But the resolution limit of an actuator was not developed and doesn\`t follow up the development of spot & pit size. Because of them, we should improve a resolution of an actuator. Especially, in this paper an actuator if studied and designed for NFR (in using SIL(Solid Immersion Lens) system. It is a dual stage actuator, which consists of a Fine actuator and a Coarse actuator. and should desire 100nm accuracy. Its actuating force generation method is VCM(Voice Coil Motor). The Fine actuator is composed of 4-leaf springs and a bobbin wrapped by coil. The Coarse actuator has Coils and 3-Roller bearings. Also, The Characteristics of designed actuator for NFR system is estimated by Sine-Swept mode and LDV(Laser Doppler Vibro-meter).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.2
• /
• pp.476-484
• /
• 2010

Recently, as the piezoelectric transformer technology develops, piezoelectric transformer may become a variable alternative to magnetic transformers in various applications. Because it was have to favorable characteristics such as electromagnetic-noise free, compact size, higher efficiency, and superior power density, linkage flux, noiseless, etc. its resonance frequency was used to output waveform of a sine wave. In this paper, the switching mode power supply of about 87.2[KHz] is driven by the multilayer thickness vibration mode piezoelectric transformer and the DC to DC converter drive circuit using an electrical equivalent circuit is proposed. Also, it was possible to drive power source device of the high-luminance LED by propose circuits.