• Journal of Drive and Control
• /
• v.11 no.2
• /
• pp.30-35
• /
• 2014

The pumps of electro-hydrostatic actuators operate most frequently in boundary lubrication speed range, as they compensate for the position control errors as a control element. When conventional swash plate type piston pumps are applied to electro-hydrostatic actuators, the frictional power losses as well as the wear rate of sliding components, such as piston shoes can increase drastically under the boundary friction condition. In this paper, the power losses of the piston shoes were investigated which were engendered by a frictional solid-to-solid contact and leakage flow rate of their hydrostatic bearing. In order to reduce them, DLC-coating was applied to the swash plate and the ball joint of pistons along with its effects were demonstrated. In addition, it was also shown that the wear rate of the piston shoes could be markedly reduced using the DLC-coated swash plate.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.1108-1111
• /
• 2009

Auto Pilot is the system which move automatically the vessel through locating operation mode to automatic after entering operating course using a electronic chart or plotter. And water jet is the a propulsion system that make a power to push the vessel through spouting the accelerated water which is absorbed by the hole in the bottom of vessel. The water jet receive the effect of the depth of water lowly, it's acceleration efficiency is higher under high speed and have an advantage on vibrating and floating sound, so it's demand is increasing as new propulsion system. However, the signal systems of auto pilot and water jet are different, we need the system to interface between each system. We designed the interface that efficiently digital feed back control embedded module between auto pilot and water jet system in this paper.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.1
• /
• pp.49-56
• /
• 2008

When the outdoor air temperature decreased less than the freezing temperature, frost forms at the surface of heat exchangers and it makes the performance degradation of a heat pump system. In this study, a heat pump system has been developed which has a refrigerant heating device as an auxiliarly heating equipment. To reduce power consumptions of the system, a liquid pump, rather than a compressor, was used to drive refrigerant in the heat pump cycle. Ratio of refrigerant mass flow between a refrigerant heating heat exchanger(GHX) and a outdoor plate heat exchanger(PHX) was varied and the system performance was measured and analyzed. As results, when the refrigerant flow rate to the GHX was decreased, the system performance is decreased due to heat absorption capability restriction of the GHX and small variation of the power consumption in the compressor. The effect on the evaporating and condensing pressure by the distribution ratio of the refrigerant to the each heat exchanger is small compare to the effect by the frequency change in the compressor. When the compressor was replaced by the liquid pump, the capacity of the system decreased a little, however the power consumption decrease approximately 80% compare with the power used in the compressor.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.9
• /
• pp.1254-1262
• /
• 2021

Recently, the agricultural environment in Korea is rapidly changing due to the aging and decline of the agricultural population, and in order to solve these problems, it is urgently required to improve the agricultural productivity and reduce the labor force. To solve this problem, a smart farm fused with ICT technology is being proposed as an alternative. In Korea, smart farms are currently mainly used in greenhouses. In this paper, this smart farm technology is to be applied to the cultivation of sprouted ginseng. To this end, we use seedlings (about 1.0g) to grow a solid medium and bed for cultivating sprouted ginseng, a fresh ginseng that is produced in a short period of time (2~3 months) with a clean environment management technology that does not use chemical pesticides and hydroponics in a greenhouse developed. In addition, an IoT-based growth environment management system was developed to monitor the growth process of sprouted ginseng in such an environment and to control driving devices.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.517-523
• /
• 2019

Recently, researches about automobile seat having function to support the comfort to driver and passenger during the driving are conducted in various fields including automobile seat having massage function. The effect of massage depends on the pattern of massage such as time, magnitude, and shape. In this paper, linear motor actuator, which is used as driving method in the automobile massage seat, and electromagnetic analysis method, which is used to improve the magnetic efficiency in the design of autuator, is proposed. Electromagnetic analysis using finite element method is conducted in the design of linear motor actuator. Input voltage shape for massage pattern is calculated by simulation using mathematical model of actuator. Performance test for massage pattern generation is conducted with automobile massage seat having developed actuator and controller. It is verified that developed actuator system is applicable in the automobile massage seat.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.1
• /
• pp.22-35
• /
• 2019

Development of low cost rechargeable batteries has been considered as a significant task for future large-scale energy storage units (i.e. electric vehicles, smart grids). Sodium-ion batteries (SIBs) have been recognized as a promising alternative to replace conventional lithium-ion batteries (LIBs) because of their abundancy and economic benign. Nevertheless, Na ions have larger ionic radius than that of Li ions, resulting in sluggish transport of Na ions in electrodes for cell operation. There have been efforts to seek suitable anode materials for the past years operated based on three different kinds of reaction mechanism (intercalation, alloy reaction, and conversion reaction). In this review, we introduce a class of conversion reaction anode materials for Na-ion batteries, which have been reported.

• Journal of Korea Water Resources Association
• /
• v.54 no.1
• /
• pp.39-48
• /
• 2021

The experiment of rip current at successive ends of breaking wave crests was conducted in a laboratory wave basin, and its time-varying evolution according to incident wave durations was observed by using ortho-rectified images. The experiment utilized the generation of a quasi nodal line of the honeycomb-pattern waves (i.e., intersecting wave trains) formed by out-of-phase motion of two piston-type wave makers arranged in the transverse direction, instead of the original honeycomb pattern waves which are generated when two wave trains propagate with slightly different wave directions. The particle moving distance and velocity caused by the rip current were measured by using the particle tracking technique. As a result, the rip current was survived for a while even without incident waves after its generation due to several successive ends of wave crests, and it moved the particles further out to sea.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.21 no.4
• /
• pp.89-100
• /
• 2011

Physical memory analysis has been an issue on a field of live forensic analysis in digital forensics until now. It is very useful to make the result of analysis more reliable, because record of user behavior and data can be founded on physical memory although process is hided. But most memory analysis focuses on windows based system. Because the diversity of target system to be analyzed rises up, it is very important to analyze physical memory based on other OS, not Windows. Mac OS X, has second market share in Operating System, is operated by loading kernel image to physical memory area. In this paper, We propose a methodology for physical memory analysis on Mac OS X using symbol information in kernel image, and acquire a process information, mounted device information, kernel information, kernel extensions(eg. KEXT) and system call entry for detecting system call hooking. In additional to the methodology, we prove that physical memory analysis is very useful though experimental study.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.6
• /
• pp.411-419
• /
• 2020

The experiment of unsteady rip current generated at the successive ends of breaking wave crests of honeycomb pattern waves was conducted in a laboratory wave basin, and its time-varying evolution was observed by using ortho-rectified images. The present experiment utilized the generation of a quasi nodal line of the honeycomb-pattern waves formed by out-of-phase motion of two piston-type wavemakers arranged in the transverse direction, instead of the original honeycomb pattern waves which are generated when two wave trains propagate with slightly different wave directions. The velocities of rip current were measured by using the LSPIV (Large-Scale Particle Image Velocimetry) technique. As a result, the unsteady rip current was generated between successive ends of wave crests, and evolved with its shear fluctuations in this experiment. Also, the time series of LSPIV velocity of the unsteady rip current showd its short component due to waves and its long component due to wave-induced currents.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.4
• /
• pp.63-73
• /
• 2021

The radar operated to detect/track aircraft targets is divided into a search radar that operates while the antenna rotating device rotates for the purpose of detecting the target according to the mission characteristics, and a tracking radar that periodically steers and tracks a beam to the predicted position of the target. The tracking radar has a shorter target information acquisition preiod than the search radar. Due to this characteristic, the tracking accuracy is better than that of the search radar, but as the prediction error increases due to the speed error at the beginning of the tracking, there are many cases in which tracking fails at the beginning of tracking due to failure to perform beam steering normally. In this paper, in order to solve the above-mentioned problems, we propose an algorithm for improving the accuracy of track initiation using radial velocity measurements in addition to the position of the measured, and confirm the performance of the proposed algorithm by comparing with the two point differential algorithm