• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.46-53
• /
• 2014

An automatic grease lubricator provides an adequate amount of fresh grease constantly to any type of rotating machine to minimize friction heat and reduce friction loss. This study seeks to develop an automatic grease lubricator by means of rapid prototyping with a gear-driven mechanism and a controlled operation time. The ultimate design is to lubricate an adequate amount of grease by a simple dip-switch clicking mechanism according to an advanced set cycle. The backlash of the gear was minimized to increase the power, and to increase the power of the mechanism, the binding frequency and the thickness of the coil were changed. To control the rotation cycles of the main shaft according to certain set numbers, different resistances and chips were used in the design of the circuit which controls the electrical signals via a pulse. A digital mock-up was analyzed and the rapid prototyping (RP) trial products were tested with a PCB circuit and grease. An evaluation of the outlet capacity of RP trial products was conducted, as the friction caused by the outlet on the wall surface was an important factor in the operation of the equipment. Finally, a finishing process was applied to decrease the roughness of a surface to a comparable level to test the performance of the product.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.3
• /
• pp.419-425
• /
• 2010

To machine the micro hole, laser machining system is widely used, however, the system cannot fabricate the micro hole with high aspect ratio and good surface finish. To break the obstacles, the high frequency vibration mechanism with PZT (Piezoelectric Transducers) is proposed in this paper. The mechanism will vibrate the laser beam in vertical direction so that the aspect ratio and surface finish may be higher than the conventional. The mechanism vibrates the eyepiece of laser optics. In addition to the benefits, the mechanism enables us to have high precision and flexibility. It decreases burr and debris during machining. And it is able to machine various materials of workpiece. This research include high frequency and large travel range of the proposed mechanism. The PZT motion of mechanism and analysis on the sensitivity of design parameters are extracted from a finite element method (FEM) simulation. In the analysis, the target vibration mode without parasitic motion is designated to have the target frequency and high amplitude.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.7
• /
• pp.609-614
• /
• 2015

Implanted telemetry systems provide the ability to monitor different species of animals while they move within their cages. Species monitored include mice, rats, rabbits, dogs, pigs, primates, sheep, horses, cattle, and others. A miniature transmitter implanted in each animal measures one or more parameters. Parameters measured include arterial pressure, intra-pleural pressure, left ventricular pressure, intra-ocular pressure, bladder pressure, ECG, EMG, EEG, EOG, temperature, activity, and other parameters and transmits the data via radio frequency signals to a nearby receiver. Every conventional dedicated transmitter contains one or more sensors, cpu and battery. Due to the expected life of the battery, the measuring time is limited. To overcome these problems, electromagnetic inductive coupling based wireless power transmission technology using multiple transmit coils were proposed, with each coil having a different active area driven by the coil driver. In this research, a parallel resonance based coil driver and serial resonance based coil driver are proposed. From the experiments we see that the parallel coil driver shows better performance under a low impedance and multiple coils configuration. However, the serial coil driver is more efficient for high impedance transmit coils.

• Journal of Digital Contents Society
• /
• v.19 no.2
• /
• pp.407-413
• /
• 2018

In this paper, we present a scalable data delivery infrastructure for such IoT computing environment where we need a common platform where data providers share their diverse sensing data and applications can easily access and receive such data from providers. For efficient data delivery, this paper proposes a new delivery path management technique that take advantage of diverse consumer QoS when building bandwidth-efficient delivery paths. We perform primitive experiments on the path construction and reconstruction which may be major overhead of the scalable infrastructure. The results show that the proposed infrastructure achieves a high level of scalability, and demonstrates that the management overhead is not significant.

• Journal of the Korean Magnetics Society
• /
• v.9 no.1
• /
• pp.48-54
• /
• 1999

For the high speed linear motor and the transportation device at clean room, a magnetic levitation rail without contact using the repulsive force of permanent magnets was newly developed. The characteristics of repulsive and lateral forces of the magnetic levitating system using permanent magnet was studied and the devised magnetic levitating system was evaluated by analytical and experimental approaches. This system is composed of two fixed guide rails with the rare earth permanent magnet array and a moving unit which is attached two magnet pairs at each sides. Because this system was forcedly levitated by the face to face repulsive forces, levitating air gap length can be repulsive force of an auxiliary magnetic repulsion system on the center of moving unit.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1196-1199
• /
• 2017

A series-hybrid power system was designed for quad-tilt prop UAV and the characteristics was analysed. The power system consists of a 4.5kW rotary engine-generator and a li-battery as power sources, a power controller manages the overall power and supplies to the vehicle system. The output power of the engine is to be matched with the generator performance considering mechanical driving loss and generating efficiency, and also loss for charging and discharging of the battery energy. It is applied that the constant speed operation of the engine-generator to minimize overall fuel consumption by integrating the generating power and the battery energy, consequentially the battery capacity and characteristics could be important factors for improvement of the system efficiency.

• Convergence Security Journal
• /
• v.13 no.4
• /
• pp.27-32
• /
• 2013

In this paper, technologies applied to design urination detection device on diaper that issues an alarm signal to guardian within 10~20m are introduced. It features power saving that uses both low power bluetooth v4.0 chip and low-power program scheme that makes sensor and mirco-controller to be sleep mode while data is not receiving from sensor. Urination detection algorithm that utilizes the difference between previous sensing data and current values is used to improve the degree of the detection precision level. The device designed with the suggested technologies shows the performance that is 100ml of the minimum urine amount for detection, more than 90% of urination detection degree, and 100% of wireless communication success rate.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.4
• /
• pp.225-230
• /
• 2004

An electromagnetic actuator has been designed and fabricated for Probe-based data storage applications. The actuator consists of permanent magnets(SmCo) housing and a media Platform which is connected to the Si frame by four couples of Si leaf springs. In order to generate electromagnetic force, Cu coils were electroplated under the media platform. The magnetic field distribution was calculated with 3D Finite Element Method of Maxwell 3D program. The field strength felt by Cu coils was estimated to be about 0.33T when the distance between the media platform and permanent magnets is $200\mu\textrm{m}$. The static and dynamic motions of the actuator were analyzed by FEM method with ANSYS 5.3. The measured displacements of the actuator were about $\pm$$92\mu\textrm{m}$ for input current of $\pm$40㎃ and the resonance frequency was 100Hz. The proposed electromagnetic actuator can be utilized for media driver of probe-based data storage system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.4
• /
• pp.331-338
• /
• 2005

In this paper the novel pulsewidth modulation(PWM) technique for the two-leg and four-leg two-phase inverter is proposed. The conventional space vector PWM technique for two-phase inverter was complex. The proposed PWM for two-leg inverter, which is used by sinusoidal PWM method, is simpler than the conventional SVPWU technique. Also, a simple PWM technique for four-leg two-phase inverter is proposed. Such PWM technique is based on PWM technique for two-leg inverter. Practical verification of theoretical predictions is presented to confirm the capabilities of the new techniques.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.452-454
• /
• 2007

PSP를 이용한 의자로봇 시스템은 거동이 불편한 노약자의 이동을 돕기 위하여 제작된 지능형 이동로봇이다. 원하는 곳으로 이동이 가능한 지능형 로봇은 안정적인 움직임을 위해 실시간 장애물 회피 및 적절한 경로 계획이 필요하다. 본 논문에서 구현한 의자로봇은 IR센서와 초음파 센서를 이용하여 환경 정보를 얻어오고, 환경 지도 작성 및 경로 계획을 통해 목표 지점으로 이동하도록 하였다. 또 구동부의 부드러운 움직임을 위하여 PID제어기를 사용하였다. 서비스 로봇은 개발에 용이하고 사용자가 쉽게 제어 할 수 있는 인터페이스 장치가 필요하다. PSP는 여러 개의 버튼을 가졌고, 디스플레이를 위한 LCD 있다. 또 무선랜 환경에서 사용할 수 있기 때문에 PSP를 이용한 제어 방법을 구현하였다. PSP를 이용한 제어 방법에는 두 가지 모드가 존재하는데 하나는 의자 로봇의 지능을 이용한 이동방법이고 또 하나는 사용자가 직접 제어하는 방법이다. 위의 두 가지 방법으로 실내 환경에서 주행 테스트를 했으며, 성공적으로 동작함을 확인하였다.