• Fire Science and Engineering
• /
• v.30 no.4
• /
• pp.27-38
• /
• 2016

The paper reports the development of a distributed temperature sensing (DTS) system, which is a fire detection system using optical sensor linear detectors that depends on foreign and domestic technologies. This study accordingly analyzed the electrical signal patterns of Raman scattering light mainly used for temperature sensing among back-scattered light generated in optical fiber by using an oscilloscope. Through the measurement results, it could be verified that the Stokes signal patterns had little change by the temperature increase, but the temperature-sensitive anti-Stokes patterns had relative increase of the changes. This study developed a K-DTS system, which is an optical sensor linear fire detection system composed of an optical repeater and a receiver that can detect fires using Raman scattering light. It could be verified that the developed K-DTS system satisfied the type approval standards through the sensitivity tests using the rate of rise type and fixed temperature type sensitivity testers. In addition, performance experiments have been performed for performance evaluation of the K-DTS system developed in comparison with S-DTS system which has been imported from abroad and widely used in Korea. It can be confirmed from the results of the performance experiments using model tunnels that comparable performances can be obtained in fire detection locations and the measurements of fire temperatures.

• Korean Journal of Optics and Photonics
• /
• v.32 no.3
• /
• pp.120-125
• /
• 2021

We have developed a linearly polarized high-power Yb-doped fiber laser in the master oscillator power amplifier (MOPA) scheme for efficient spectral beam combining. We modulated the phase of the seed laser by pseudo-random binary sequence (PRBS), with the bit length optimized to suppress stimulated Brillouin scattering (SBS), and subsequently amplified seed power in a 3-stage amplifier system. We have constructed by coiling the polarization-maintaining (PM) Yb-doped fiber, with core and cladding diameters of 20 ㎛ and 400 ㎛ respectively, to a diameter of 9-12 cm for suppression of the mode instability (MI). Finally, we obtained an output power of 1.004 kW with a slope efficiency of 83.7% in the main amplification stage. The beam quality factor M² and the polarization extinction ratio (PER) were measured to be 1.12 and 21.5 dB respectively. Furthermore, the peak-intensity difference between the Rayleigh signal and SBS signal was observed to be 2.36 dB in the backward spectra, indicating that SBS is successfully suppressed. In addition, it can be expected that the MI does not occur because not only there is no decrease in slope efficiency, but also the beam quality for each amplified output is maintained.

• Korean Journal of Optics and Photonics
• /
• v.33 no.2
• /
• pp.67-73
• /
• 2022

In a head-mounted display (HMD) for virtual-reality applications, a narrow viewing angle is preferred to the usual, wide viewing angle because the HMD is positioned close in front of the user's eyes, and the display position is fixed. In this paper, we propose a new back-light unit (BLU) for implementing a narrow viewing angle, which is suitable for a HMD. By optimizing the scattering patterns in the light-guide-plate and inverse-prism structures, the viewing angle and correlations between structural parameters in the BLU components are analyzed with ray-tracing simulations. As a result, a double-angle inverse-prism structure incorporating the scattering patterns of a light-guide plate is chosen, which results in a 14% increase in center luminance, a 16% decrease in the vertical viewing angle, and a light efficiency of up to 70%, compared to a conventional BLU. Thus, the new BLU system is expected to be applied in a high-efficiency liquid crystal display.

• The Korean Journal of Malacology
• /
• v.29 no.4
• /
• pp.263-272
• /
• 2013

The development of swift's scallop Chlamys swiftii, reared in the laboratory, has been examined through the investigation of morphological characteristics in fertilized egg, larvae and juvenile. Eggs were fertilized with a dilute sperm solution to improve the survival of fertilized eggs. Developing larvae were maintained at a temperature of $16{\pm}0.5^{\circ}C$ and salinity concentration of 33 ppt. We have investigated the fertilization rates and egg number spawned at several stimulating conditions such as sunlight exposure, air dry, seawater temperature rise ($5^{\circ}C$) and seawater temperature rise ($5^{\circ}C$) after exposure of air dry for spawning induction of swift's scallop Chamys swiftii. Stimulation treated with sunlight exposure and seawater temperature rise ($5^{\circ}C$) have shown the spawning number of 700,000-900,000 and 700,000-800,000 per individual, respectively while stimulation treated with seawater temperature rise ($5^{\circ}C$) after exposure of air dry have shown the high spawning number of 1,000,000-1,500,000 per individual. Survival rate of D-shaped larvae of swift's scallop put into the different seawater temperatures of $8^{\circ}C$, $12^{\circ}C$, $16^{\circ}C$, $20^{\circ}C$ and $24^{\circ}C$ has been 4.1%, 11.6%, 32.7%, 18.6% and 3.2%, respectively. Fertilized eggs with the diameter of $72{\mu}m$ developed into trochophore larvae of $103{\pm}3.8{\mu}m$ shortly after 35 hours and to D larvae of $129{\pm}10.4{\mu}m$ shell length within 72 hours. It took 336 hours to become initial Umbo-stage larva of $145{\pm}16.8{\mu}m$ shell length. Post larvae, which have been $197{\pm}13.6{\mu}m$ shell length, spontaneously have settled in the attachment substances. It have required 528 hours from fertilized eggs to early attached juvenile to become initial juvenile size of $245{\pm}15.8{\mu}m$ shell length.

• Korean Journal of Optics and Photonics
• /
• v.11 no.6
• /
• pp.434-440
• /
• 2000

We fabricated a high power Nd:YAG laser pumped by a 1 kW diode laser with a Lambertian-type diffusive reflector. Maximum cw power of 500 W with a slope efficiency of 49%, which corresponds to an optical efficiency of 46.7%, was obtained from a short linear resonator when a 5 mm rod was used. The efficiencies decreased when a 6 mm rod was used, due to the poor quality of the absorption distribution in the rod. The measured beam quality factor of 70, which is slightly smaller than the value calculated from the measured thermal focal lengths, shows that the absorption distribution in the rod is fairly uniform. iform.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.370-373
• /
• 2003

Superluminescent diodes(SLDs) are the optimum light sources for application in optical measurement systems such as fiber gyroscopes, optical time domain reflectometers, and to short and medium distance optical communication systems. The broadband characteristics of SLDs reduce Rayleigh backscattering noise, polarization noise, and the bias offset due to the nonlinear Kerr effect in fiber gyro systems. In this paper, in order to suppress lasing oscillation, we introduced a laterally tilted SCH(Separate Confinement Heterostructure)-SLD with a window region. An output power of 11mW has been achieved at 200mA injection current at 25$^{\circ}C$. At 120mA, parallel and perpendicular to the junction were 31$^{\circ}$${\times}$38$^{\circ}$.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.4
• /
• pp.500-505
• /
• 2011

In this paper, two types of micro-optic submersion detection systems are proposed and demonstrated. The structures are based on the transmission and reflection of incident light, respectively. Two collimators are separated by 10 mm and installed face to face in straight line. The incident light transmits from one side of collimator to the other through the air, but the optical loss is below 1 dB. On the other hand, when the sensors are submersed into water, most of optical power scattered into water. The systems monitor the dramatical power change to alarm the submersion. Reflection type of sensor system has a Bragg grating at the end of the sensor for back-reflection of sensing signal. This is for simple configuration of systems. The performance of two sensor systems are described in detail.

• Korean Journal of Optics and Photonics
• /
• v.13 no.2
• /
• pp.155-161
• /
• 2002

The nail bed is located under the finger nail. The arched portions of the nail bed, which contain a large number of capillary loops, are separated by the valley of the nail bed. The valley of the nail bed does not contain capillary loops. Light is scattered when it propagates through the dermis of skin, and human blood strongly absorbs the light with proper wavelength. By use of the optical properties of the nail bed, we propose an optical technique which extracts the nail bed image of the finger nail. After achieving nail bed images of each individual, we correlated between them. The correlation outputs show that we can identify individuals by comparing the peak heights of the correlation outputs.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.32.1-32.1
• /
• 2010

본 연구에서는 질화물계 발광 다이오드의 광추출효율을 향상시키기 위해서 Bi-layer나노 임프린트 리소그래피와 Lift-off 공정을 이용하여 ITO투명전극 층 상부에 TiO2 나노 패턴을 형성하였다. 발광 다이오드의 투명전극 층 상부에 UV 나노 임프린트 리소그래피를 이용하여 주기적인 폴리머 패턴을 형성한 후 폴리머 패턴 상부에 RF magnetron Sputtering 공법을 이용하여 TiO2를 증착하고 Lift-off 공정을 이용하여 TiO2 나노 패턴을 제작하였다. 그 결과를 주사전사 현미경(SEM)으로 확인한 결과 임프린트 스탬프와 동일한 나노 패턴이 질화물 계 발광다이오드 투명 전극층 표면에 주기적으로 형성되었다. TiO2 나노 패턴 형성을 통한 광추출 효율의 향상 효과를 확인하기 위해 Electroluminescence (EL) 측정한 결과 TiO2 나노 패턴이 형성된 발광다이오드 소자의 EL 강도가 나노 패턴이 없는 발광다이오드와 비교하여 12% 정도 향상 되었음을 보였고, 이는 고 굴절율 나노 패턴이 활성층에서 발생된 빛의 산란 효과를 유도하여 빛의 내부 전반사를 감소시킨 결과로 해석된다. 또한 소자의 전기적 특성평가를 위한 I-V 측정결과, TiO2 나노 패턴이 형성된 발광 다이오드의 전기적 성질이 저하되지 않았음을 확인하였다.

• Korean Journal of Optics and Photonics
• /
• v.17 no.2
• /
• pp.143-148
• /
• 2006

A new method of measuring the Brillouin gain spectrum of optical fiber is proposed and demonstrated. Unlike existing methods, both the pump light and the counter-propagating probe light are generated from a single laser diode whose optical frequency is directly modulated by injection current modulation. The frequency difference between the pump and the probe is scanned continuously through optical frequency chirp occurring when the injection current is modulated with a square wave. The measured Brillouin gain spectrum of telecom single-mode fiber agrees well with that shown in other literature.