• 정보와 통신
• /
• 제20권6호
• /
• pp.778-799
• /
• 2003

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2005년도 제28회 학술발표회 초록집
• /
• pp.146-146
• /
• 2005

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.504-505
• /
• 2012

• 대한기계학회논문집B
• /
• 제27권1호
• /
• pp.25-31
• /
• 2003

Airborne contaminant particles are intruded into optical disk drives(ODD) due to the flow caused by disk rotation and can be adhered to lens or disk surfaces, which causes decrease of laser power and increase of read/write errors. Such a phenomenon can be more serious as the space between the disk and the lens is reduced fur high-density storage devices. The purpose of this paper is to understand design parameters to reduce the particle intrusion into an ODD. Suggestions are made to prevent the particle intrusion that can decrease the stability of an ODD and also prevent the potential heat build-up problem. The sealing effect of drive and the forced injection of clean air (using HEPA filter) into the drive minimizes intrusion of the outside air and dusts in an ODD remarkably. Moreover it is proved by experiments that the installation of a heatproof pad to isolate heat generation part (PCB) from information read/write sections and the forced injection of dust-free air reduce the gas temperature inside the drive as well as the amount of particles intruded.

• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1545-1551
• /
• 2002

The optical storage device has recently experienced significant improvement, especially for the aspects of high capacity and fast transfer rate. However, it is necessary to study a new shape of air bearing surface for the rotary type actuator because the optical storage device has the lower access time than that of HDD (Hard Disk Drives). In this study, we proposed the air bearing shape by using SA (Simulated Annealing) algorithm which is very effective to achieve the global optimum instead of many local optimums. The objective of optimization is to minimize the deviation in flying height from a target value 100nm. In addition, the pitch and roll angle should be maintained within the operation limits.

• 한국소음진동공학회논문집
• /
• 제15권1호
• /
• pp.29-38
• /
• 2005

The track pull-in behavior analysis in an optical disk drive (ODD) using plane phase and the evaluations for effecting parameters of it are discussed. Track pull-in, track capture procedure to do track following control, is a key factor to increase data transfer rate. First, the relative velocity between the beam spot of an optical pick-up and the target track of an optical disk is analyzed during the track pull-in procedure. In this process, it is showed that the track error signal has nonlinear characteristics which are depending on the time. Second, Runge-Kutta method to solve the nonlinear equation is applied to find the track pull-in behavior, and some optimal parameters to get stable and fast pull-in condition are obtained. Then, the phase plane analysis for track pull-in procedure is presented. Finally, some comments for the simulated results are discussed briefly.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1284-1287
• /
• 2007

Recently, the need for slim type optical disk drive(ODD) has increased with popularization of lightweight notebook. Because of its lightweight and small structure, slim type ODD has low structural stiffness and it is weak to high-speed disk vibration. In this paper, Finite Element(FE) Model of slim type ODD is constructed and verified by experimental modal analysis. Additionally, sensitivity analysis is performed about structural parameters. As a result of sensitivity analysis, improved characteristic is verified by experiments using a sample of new model.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.474-478
• /
• 2006

It is becoming more significant to develop a rotary voice coil motor(VCM) type's actuator for small form factor (SFF) optical disk drive(ODD), as portables are getting more and more popularized nowadays. The actuator which is applicable to small-sized ODD with a compact flash(CF) II card size was developed and fabricated. The experimental results showed that the finite element(FE) model is different from the fabricated model. And so flexible mode frequencies did not satisfy specifications of small-sized ODD, and tuning. Tuning procedures were required to improve dynamic characteristics of the fabricated actuator through finite difference method(FDM). At first, design variables were extracted through parameter study and the tuned FE model was improved by design of experiment(DOE). Consequently, It was confirmed that the improved model was applicable to SFF ODD.

• 한국지능시스템학회논문지
• /
• 제14권5호
• /
• pp.598-603
• /
• 2004

광디스크에 저장된 데이터를 읽기 위한 광디스크 드라이브는 광학헤드 구동기의 포커싱 서보계와 트랙킹 서보계로 구성된다. 기존에 사용하는 지상-진상-진상 보상기는 시스템의 배속이 증가하면서 광학헤드의 구동기 제어가 점점 어려워지는 추세이다. 따라서 본 논문에서는 광학헤드 구동기 서보계 구현을 위하여 유전알고리즘 기반 퍼지 PID 제어 광학헤드 구동기 설계 기법을 제안한다. 제안된 광학헤드 구동기는 두개의 퍼지 PI, PD 제어 블록으로 구성되며 두 제어기의 퍼지 규칙은 유전알고리즘을 사용하여 최적화된다. 구동기의 포커싱, 트랙킹 서보계의 플랜트 모델은 유사하므로 트랙킹 서보계의 모의 실험만을 통하여 제안된 기법의 우수성을 보인다.

• 대한기계학회논문집B
• /
• 제29권2호
• /
• pp.224-231
• /
• 2005

The present study investigates flow characteristics in an optical disc drive (ODD). Detailed knowledge of the flow characteristics is essential to analyze flow-induced noise and vibration, forced convection and flow friction loss. The ODD used in a personal computer is used for the experiment and rotating velocity of disc is under the 4500 rpm. Time-resolved velocity component and velocity spectrum are obtained using the laser Doppler anemometry (LDA), and the flow patterns induced by rotating disc in the ODD are calculated by a commercial finite volume method at the same time. The results show that the front holes reduce flow-induced noise and the position of pickup body only affects flow near the window. Furthermore, it is possible for cooling of heat sources in the drive through measuring the flow fields under the tray. In addition, the numerical results are well matched up to the experimental results, therefore, the validation of the numerical results can be achieved. From the validation of numerical results, it is possible to predict the flow characteristics of the region where it is unable to conduct the experiment.