• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.15-21
• /
• 2000

Optical fiber temperature sensor, using resonance wavelength shifting of single mode fiber-to-planar waveguide coupler by heat, was fabricated. Thermo-optic polymers, have large change of refractive index due to heat, were used for planar waveguide. The device fabrication procedure including fiber polishing steps was illustrated and the device structure with independent polarization was demonstrated experimentally. The resonance wavelength difference of fabricated device was less than 2nm. The resonance wavelength shifting owing to temperature variation, from room temperature($24^{\circ}C$) to $90^{\circ}C$, was showed $-0.54nm/^{\circ}C$, $-3nm/^{\circ}C$.

• Korean Journal of Optics and Photonics
• /
• v.18 no.6
• /
• pp.441-446
• /
• 2007

Outcoupling efficiency of the OLED device is improved by incorporating both a microlens array and a diffractive grating pattern. The microlens array improves the light transmission at the interface of glass and air, and the diffractive grating outcouples the guided mode propagating at the waveguide, which consists of ITO and organic layers. By using the PDMS soft mold imprinting method, the microlens array is fabricated on the glass substrate. The diffractive grating pattern is directly fabricated on the ITO surface by using laser interferometry. A microlens array with a diameter of $10{\mu}m$ improves the light coupling efficiency by 22%. The diffractive grating made of TSMR photoresist enhances the luminance power efficiency by 41% at a current density of $20mA/cm^2$.

• Korean Journal of Optics and Photonics
• /
• v.17 no.2
• /
• pp.175-180
• /
• 2006

A single sideband(SSB) modulator operating at 5.5 GHz was fabricated by polarization inversion techniques. The dimension of domain inversion in a $LiINbO_3$ Mach-Zehnder structure was precisely controlled so that the RF signal applied on two Mach-Zehnder arms gives rise to $90^{\circ}$ effective phase difference. The single sideband suppression was maximized by optimization of the polarization status of the optical input and by the DC bias value. The fabricated device showed the center frequency of 5.8 GHz and the maximum sideband suppression of 33dB, where the bandwidth of 15 dB sideband suppression ranged over a 2.5 GHz span. The optical phase delay could be regulated by the DC bias voltage, fur example, the enhanced optical modulation sideband was distinctively switched from the upper sideband to the lower sideband by changing the DC bias voltage from 1.9 V to -10.6 V.

• Korean Journal of Optics and Photonics
• /
• v.8 no.3
• /
• pp.230-235
• /
• 1997

Coupling loss variation as the shape of fiber ends and the fiber arrangement in a fiber Fabry-Perot cavity, formed with two optical fibers with dielectric mirror coatings on their ends, is analyzed. For the intended features it is assumed that one of two fibers is processed to have a concave mirror whose curvature is the same as that of the wavefront of the Gaussian beam from the first fiber. In this assumption, it was turned out that the coupling loss at the cavity length of 15 ${\mu}{\textrm}{m}$ is less than 0.5% even with tilt angle of 0.2$^{\circ}$, curvature error of 70 ${\mu}{\textrm}{m}$, cavity length error of 8 ${\mu}{\textrm}{m}$, and lateral alignment error of 0.5 ${\mu}{\textrm}{m}$. Thus, low loss and high-finesse fiber Fabry-Perot filters whose cavity length is greater than several ${\mu}{\textrm}{m}$ can be obtained easily if the receiving fiber end is properly formed.

• Journal of Sensor Science and Technology
• /
• v.32 no.4
• /
• pp.223-231
• /
• 2023

An integrated-optical biochemical sensor structure that can perform homogeneous and surface sensing using a 2×2 balanced-bridge Mach-Zehnder interference structure based on the optimized SOI slot optical waveguide was described, and its performance and characteristics were evaluated. Equations for the two output optical powers were derived and examined using the transfer matrices of a 3-dB coupler and phase shifter (channel waveguide). The length of the 3-dB coupler was determined such that the two output optical powers were same using these formulas. In homogeneous sensing, the effect of the refractive index of an analyte in the range of 1.33-1.36 on the two output optical power distributions was numerically derived, and the sensitivity was calculated based on each output and the difference between the two outputs, the former and the latter being 7.5796-19.0305 [au/RIU] and 15.2601-38.1351 [au/RIU], respectively. In the case of surface sensing, the sensitivity range of the refractive index of 1.337 based on each of the two outputs was calculated as -2.2490--3.5854 [au/RIU] and 1.2194-3.8012 [au/RIU], and the sensitivity range of 4.8048-7.0694 [au/RIU] was confirmed based on the difference between the two outputs.

• Korean Journal of Optics and Photonics
• /
• v.31 no.5
• /
• pp.213-217
• /
• 2020

In this study we report a wet-etching-based fabrication method for adiabatic optical-fiber tapers (OFTs), and describe their adiabaticity and HE₁₁ mode evolution at a wavelength of 1550 nm. The profile of the fabricated system satisfies the adiabaticity properties well, and the far-field pattern from the etched OFT shows that the fundamental HE₁₁ mode is maintained without a higher-order mode coupling throughout the tapers. In addition, the measured far-field pattern agrees well with the simulated result. The proposed adiabatic OFTs can be applied to a number of photonic applications, especially fiber-chip packages. Based on the fabricated adiabatic OFT structures, the optical transmission to the inversely tapered silicon waveguide shows large spatial-dimensional tolerances for 1 dB excess loss of ~60 ㎛ (silicon waveguide angle of 1°) and insertion loss of less than 0.4 dB (silicon waveguide angle of 4°), from the numerical simulation. The proposed adiabatic coupler shows the ultrabroadband coupling efficiency over the O- and C-bands.

• Korean Journal of Optics and Photonics
• /
• v.24 no.4
• /
• pp.184-188
• /
• 2013

Two types of polymer-based optical splitters with $200{\mu}m$ large core are presented for optical multimode networks, such as smart home networks, intelligent automotive networks, etc. Optical splitters that have 1:1 symmetric and 9:1 asymmetric structure were fabricated by a ultra violet(UV)-imprint technology using a deep etched Si(silicon) master by the Bosch process. In this paper, we successfully fabricated the symmetric and asymmetric optical splitters with suitable optical network applications.