• Korean Journal of Materials Research
• /
• v.29 no.9
• /
• pp.553-558
• /
• 2019

$Cu_2ZnSn(S,Se)_4(CZTSSe)$ thin film solar cells areone of the most promising candidates for photovoltaic devices due to their earth-abundant composition, high absorption coefficient and appropriate band gap. The sputtering process is the main challenge to achieving high efficiency of CZTSSe solar cells for industrialization. In this study, we fabricated CZTSSe absorbers on Mo coated soda lime glass using different pressures during the annealing process. As an environmental strategy, the annealing process is performed with S and Se powder, without any toxic $H_2Se$ and/or $H_2S$ gases. Because CZTSSe thin films have a very narrow stable phase region, it is important to control the condition of the annealing process to achieve high efficiency of the solar cell. To identify the effect of process pressure during the sulfo-selenization, we experiment with varying initial pressure from 600 Torr to 800 Torr. We fabricate a CZTSSe thin film solar cell with 8.24 % efficiency, with 435 mV for open circuit voltage($V_{OC}$) and $36.98mA/cm^2$ for short circuit current density($J_{SC}$), under a highest process pressure of 800 Torr.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.1
• /
• pp.94-100
• /
• 1999

Mercurous chloride($Hg_2Cl_2$) crystals hold promise for many acousto-optic and opto-electronic applications, which are prepared in closed ampoules by the physical vapor transport(PVT) growth methods. The thermal boundary conditions established by imposing different temperature on sidewalls of the enclosure cause simultaneous horizontal and vertical convectie flow in the PVT processes of$Hg_2Cl_2$ . It is found that for the ratios of horizontal to vertical thermal Rayleigh numbers$Ra_H/Ra{\ge}1.5$, the convective flow structure changes from multicellular to unicellular for the base parametric state of Ra=($2.79{\times}10^4$) , Pr=0.91, Le=1.01, Pe=4.60, Ar=0.2 and$C_V =1.01$. For the $\Delta T^{*}_H$ greater than 0.3, the $$\mid$U$\mid$_{max}$is increased with increasing $\Delta$ T^{*}_H$ and decreasing the aspect ratio. For the aspect ratios ranging from 0.1 to 1.0, there is a direct and linear relationship between $$\mid$U$\mid$_{max}$ and $\sqrt{{\Delta}T^_H\;^{\ast}}$.A decrease in the aspect ratio destabilizes the convective flow and results in an increase of the magnitude of convection in the crystal growth reactor. The vertical gradient tends to destabilize the convective flow which leads to oscillations, whereas the horizontal gradient stabilizes the convection.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.130-130
• /
• 2017

Au 합금 도금층은 내마모성 및 내식성이 우수하고 접촉저항이 낮기 때문에, 커넥터, 인쇄회로기판 등과 같은 전자부품의 접속단자부에 널리 적용되고 있다. 각 부품들을 효과적으로 전기적 신호를 통해 연결하기 위해서는 낮은 접촉저항이 요구되며, 이러한 Au 합금 도금층의 접촉저항은 합금 원소의 종류 및 함량, 용융 솔더와 전자부품을 고정시키는 표면실장공정에서 받는 theremal aging의 온도와 시간에 따라 변화된다. 현재 전자부품용 커넥터에 실시되고 있는 금 합금도금은 Au-0.3wt%Co합금, Au-0.2wt%Ni합금도금이 대부분 적용되고 있으며, 높은 순도(금 함유량 99.7wt%이상)로 인하여 금 사용량을 절감하기 어려운 실정이다. Sn은 Au와 높은 고용률을 갖는 합금을 형성하는 장점을 갖고 있기에 금 사용량 절감에 큰 기여를 할 수 있을 것으로 예상된다. 따라서 본 연구에서는 Sn을 합금 원소로 사용하여 높은 Sn함량을 갖는 Au 합금 도금층을 제작하고, 무연솔더의 융점보다 더 높은 온도인 533K에서 thermal aging을 실시하여, Sn함량별로 thermal aging에 따른 접촉저항과 솔더퍼짐성의 변화를 기존의 Co, Ni합금과 비교 조사하였다. 또한, 표면분석을 통하여 Au-Sn합금 도금층의 접촉저항이 변화하는 요인에 대해서도 고찰하였다. 표면적 $0.2dm^2$의 순수 동 시편 위에 약 $2{\mu}m$두께의 Ni도금을 실시한 후 Sn 함량을 다르게 준비한 도금 용액(Au 6g/L, Sn 1~8g/L)을 사용하여 Au-Sn합금 도금을 실시하였다. Au-Sn합금 도금층은 전류밀도 0.5ASD, 온도 $40^{\circ}C$에서 약 $0.1{\mu}m$두께가 되도록 도금하였으며, 두께는 형광X선 도금두께측정기로 측정하였다. 금 합금 도금층 내의 Sn함량은 Ti시편 위에 도금한 Au-Sn합금층을 왕수에 용해시킨 다음, ICP를 사용하여 분석하였다. Au-Sn합금 도금층의 접촉저항은 준비된 시편을 533K에서 1분 30초, 3분, 6분 간 열처리한 후, 5회 접촉저항을 측정하여 그 평균값으로 하중에 따른 금 합금 도금층의 접촉저항을 비교하였다. 솔더링성은 솔더볼을 합금 표면에 솔더페이스트를 이용하여 붙인 뒤 533K에서 30초간 열처리하고, 열처리 후 솔더볼의 높이 변화를 측정해 열처리 전 솔더볼의 높이에 비해 퍼진정도를 측정하였다. 또한, 도금층 내의 Sn함량에 따라서 접촉저항이 변화하는 요인을 분석하기 위해서 X선 광전자 분광기를 이용하여 도금층 표면의 정량 분석 및 화학적 결합상태를 분석하였다. ICP분석결과 Au-Sn합금층 내의 Sn함량은 도금용액의 조성별로 9~12wt% Sn 합금층이 형성된 것을 알 수 있었고 기존의 Au-Ni, Au-Co 합금층과 비교해 합금함량이 크게 증가된 것을 알 수 있었다. 또한 접촉저항 측정 결과, 기존의 Au-Ni, Au-Co합금층의 접촉저항과 비교했을 때 Au-Sn합금층의 접촉저항이 더 낮은 것을 알 수 있었다. 또한, 솔더퍼짐성 측정 결과 기존의 Au-Ni, Au-Co합금층과 비교해 솔더퍼짐성이 우수한 것을 확인할 수 있었다. 따라서 전자부품용 접점재료에 합금함량이 높은 Au-Sn합금층을 적용시키면 더 우수한 커넥터의 성능을 얻을 수 있을 뿐 아니라 경제적으로 큰 절약 효과를 기대할 수 있을 것으로 판단된다.

• Korean Journal of Dental Materials
• /
• v.45 no.4
• /
• pp.257-274
• /
• 2018

The purpose of this study was to evaluate the effect of acid-treatment conditions on the surface properties of the RBM (Resorbable Blast Media) treated titanium. Disk typed cp-titanium specimens were prepared and RBM treatments was performed with calcium phosphate ceramic powder. Acid solution was mixed using HCl, $H_2SO_4$ and deionized water with 4 different volume fraction. The RBM treated titanium was acid treated with different acid solutions at 3 different temperatures and for 3 different periods. After acid-treatments, samples were cleaned with 1 % Solujet solution for 30 min and deionized water for 30 min using ultrasonic cleanser, then dried in the electrical oven ($37^{\circ}C$). Weight of samples before and after acid-treatment were measured using electric balance. Surface roughness was estimated using a confocal laser scanning microscopy, crystal phase in the surface of sample was analyzed using X-ray diffractometer. Surface morphology and components were evaluated using Scanning Electron Microscope (SEM) with Energy Dispersive X-ray spectroscopy (EDX) and X-ray Photoemission Spectroscopy (XPS). Values of the weight changes and surface roughness were statistically analyzed using Tukey-multiple comparison test (p=0.05). Weight change after acid treatments were significantly increased with increasing the concentration of $H_2SO_4$ and temperature of acid-solution. Acid-treatment conditions (concentration of $H_2SO_4$, temperature and time) did not produce consistent effects on the surface roughness, it showed the scattered results. From XRD analysis, formation of titanium hydrides in the titanium surface were observed in all specimens treated with acid-solutions. From XPS analysis, thin titanium oxide layer in the acid-treated specimens could be evaluated. Acid solution with $90^{\circ}C$ showed the strong effect on the titanium surface, it should be treated with caution to avoid the over-etching process.

• Polymer(Korea)
• /
• v.30 no.6
• /
• pp.538-544
• /
• 2006

Two kinds of novel bifunctional methacrylated prepolymers (170-2MA and 631-2MA) which have similar structure with 2,2-bis[4- (2'-hynroxy-3'-methacryloyloxypropoxy)phenyl] propane (Bis-GMA) was synthesized for dental applications as an alternative to Bis-GMA containing bisphenol A that is doubtful as an endocrine disrupter. The organic matrices were prepared by mixing a diluent and/or a monomer with the synthesized methacrylated prepolymers. The yield, viscosity, and chemical structures of the prepolymers and the physical and methanical properties of the organic matrices were evaluated. The yields of the prepolymers synthesized through a ring-opening reaction of epoxy compound and methacrylic acid were above 90% and the viscosities of the prepolymers were much lower than that of the Bis-GMA control. From the results of $^1H-NMR$ and FTIR analyses, the chemical structures of the prepolymers were similar to that of Bis-GMA. In addition, the curing time, poly-merization shrinkage, photoconversion, polymerization depth, and compressive strength of the organic matrices formulated with 170-2MA and 631-2MA prepolymers exhibited comparable to or better than those of the existing Bis-GMA-based one. These results suggest that the novel methacrylated prepolymers which have no endocrine disrupter can be an alternative to Bis-GMA and be applicable to dental polymer materials.

• Korean Journal of Materials Research
• /
• v.11 no.5
• /
• pp.419-426
• /
• 2001

The stochiometric $AgGaSe_2$ polycrystalline mixture of evaporating materials for the $AgGaSe_2$ single crystal thin film was prepared from horizontal furnace. To obtain the single crystal thin films, $AgGaSe_2$ mixed crystal and semi-insulating GaAs(100) wafer were used as source material and substrate for the Hot Wall Epitaxy (HWE) system, respectively. The source and substrate temperature were fixed at$ 630^{\circ}C$ and $420^{\circ}C$, respectively. The thickness of grown single crystal thin films is 2.1$\mu\textrm{m}$. The single crystal thin films were investigated by photoluminescence and double crystal X-ray diffraction(DCXD) measurement. The carrier density and mobility of AgGaSe$_2$ single crystal thin films measured from Hall effect by van der Pauw method are $4.89\Times10^{17}$ cm$^{-3}$ , 129cm2/V.s at 293K, respectively. From the Photocurrent spectrum by illumination of perpendicular light on the c-axis of the AgGaSe$_2$ single crystal thin film, we have found that the values of spin orbit splitting $$\Delta$S_{o}$ and the crystal field splitting $\Delta$C$_{r}$, were 0.1762eV and 0.2474eV at 10K, respectively. From the photoluminescence measurement of AgGaSe$_2$ single crystal thin film, we observed free excision (EX) observable only in high quality crystal and neutral bound exciton ($D^{o}$ , X) having very strong peak intensity. And, the full width at half maximum and binding energy of neutral donor bound excition were 8mev and 14.1meV, respectively. By Haynes rule, an activation energy of impurity was 141 meV.ion energy of impurity was 141 meV.