• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.2 s.21
• /
• pp.58-66
• /
• 2005

This paper presents miniaturized setback generators based on the conversion of mechanical energy into electrical energy for military applications, especially power supply for electronic fuzes. In order to minimize the volume of setback generators, a ring-shaped magnet enclosing a coil assembly is adopted. A mechanical safety system, shear plate, is used as a release mechanism of the setback generators to prevent the generators from operating accidentally. The setback generators are intended not to ignite an electrical detonator but to charge a capacitor which is capable of driving electronic circuit of fuze. We design the setback generators using the simulation results of an electromagnetic analysis tool, $Maxwell^{(R)}$ 2D. In experimental study, we perform safety tests of the shear plate and firing tests of the fabricated setback generators. The present setback generators show that the voltage of 14.2V is charged at the capacitor of $30{\mu}F$ within the charging time of 0.68msec and the critical acceleration for safety is 5,000G, thus verifying that the setback generators with a ring-shaped permanent magnet can be applicable to the power supply of small-caliber electronic fuze.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.2
• /
• pp.218-226
• /
• 2016

In the original design of K2 tank the Vertical Sensor Unit(VSU) was mounted to measure the attitude of the main gun to enhance the hit probability. In this research, as a part of efforts to reduce the cost of K2, it was theoretically simulated and evaluated to use the data from Inertial Navigation System(INS) for the calculation of the gun attitude instead of the direct measurement using VSU. It was found that the negative effect of INS approach is negligible and the elimination of VSU is technically possible and beneficial to the system.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.1
• /
• pp.21-29
• /
• 2003

The Strap Down Inertial Measurement Unit(SDIMU) is recently used for the sensor package of the modern underwater vehicles such as torpedoes and unmanned underwater-vehicles. For using SDIMU, an initial alignment must be carried out before the fire or navigation stage. The general initial alignment methods require that a mother vehicle Is a stationary condition or the Inertial Navigation System(INS) of vehicle is received the specific of data navigation from the mother vehicle. But an underwater vehicle dropped from aircraft is hard to satisfy above both necessary conditions of the general initial alignment. So, we suggest a new strap down initial alignment method of an underwater vehicle dropped from aircraft without using any aided sensors. The highlight point of this method is that a period of initial alignment is not before the fire but during running stage to fix alignment error. And we verify it by analyzing various data of S/W simulations, Hardware In the Loop Simulation(HILS) tests and sea trials.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.6
• /
• pp.731-743
• /
• 2018

In this paper, a study result to decide the accuracy specifications of inertial sensors satisfying the performance requirements of SINS(ship's inertial navigation system) is proposed. To do this, the performance specifications of overseas SINS is surveyed and the detailed error analysis of SINS at stationary condition is performed. Also, a new performance index to indicate the performance of SINS is derived. Modelling and simulation results show that the accuracy specifications of inertial sensors to meet the performance requirements of SIGMA40XP, a typical overseas SINS, can be determined through the newly derived performance index in this paper.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.6
• /
• pp.577-590
• /
• 2021

In this paper, we theoretically analyzed the self-alignment/navigation performance in the accelerometer resonance state generated by dither motion of ring laser gyroscope in LINS and verified it through simulation. As a result of analysis, it is confirmed that the amplitude of the accelerometer measurement amplified in the accelerometer resonance state is decreased in the process of sampling per the navigation calculation period and that frequency is changed by the aliasing effect too. It was also analysed that the attitude error in self-alignment is determined by the amplitude/frequency of the accelerometer measurement, the gain of the self-alignment loop, and the velocity and position error in the navigation is determined by the amplitude/frequency/phase error of the accelerometer measurement. This analysis and simulation results show that the self-alignment and navigation performance is not be degraded only when the amplification factor of the accelerometer measurement in the accelerometer resonance state is 3 or less

• Journal of Ocean Engineering and Technology
• /
• v.17 no.6
• /
• pp.83-90
• /
• 2003

This paper presents an underwater hybrid navigation system for a semi-autonomous underwater vehicle (SAUV). The navigation system consists of an inertial measurement unit (IMU), and a Doppler velocity log (DVL), accompanied by a magnetic compass. The errors of inertial measurement units increase with time, due to the bias errors of gyros and accelerometers. A navigational system model is derived, to include the scale effect and bias errors of the DVL, of which the state equation composed of the navigation states and sensor parameters is 20. The conventional extended Kalman filter was used to propagate the error covariance, update the measurement errors, and correct the state equation when the measurements are available. Simulation was performed with the 6-d.o,f equations of motion of SAUV, using a lawn-mowing survey mode. The hybrid underwater navigation system shows good tracking performance, by updating the error covariance and correcting the system's states with the measurement errors from a DVL, a magnetic compass, and a depth sensor. The error of the estimated position still slowly drifts in the horizontal plane, about 3.5m for 500 seconds, which could be eliminated with the help of additional USBL information.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.467-477
• /
• 2004

A new scheme to estimate the moment of inertia in the servo motor drive system in very low speed is proposed in this paper. The typical speed estimation scheme in most servo system for low speed operation is sensitive to the variation of machine parameters, especially the moment of inertia. To estimate the motor inertia value, the observer using the Radial Basis Function Networks(RBFN) is applied. The effectiveness of the proposed inertia estimation method is verified by experiments. It is concluded that the speed control performance in the low speed region is improved with the proposed disturbance observer using RBFN.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.283-289
• /
• 2010

Owing to the increasing worldwide interest in green technology and renewable energy sources, flywheel energy storage systems (FESSs) are gaining importance as a viable alternative to traditional battery systems. Since the energy storage capacity of an FESS is proportional to the principal mass-moment of inertia and the square of the running speed, a design that maximizes the principal inertia while operatingrunning at the highest possible speed is important. However, the requirements for the stability of the system may impose a constraint on the optimal design. In this paper, an optimal design of an FESS that not only maximizes the energy capacity but also satisfies the requirements for system stability and reduces the sensitivity to external disturbances is proposed. Cross feedback control in combination with a conventional proportional-derivative (PD) controller is essential to reduce the effect of gyroscopic coupling and to increase the stored energy and the specific energy density.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.162-170
• /
• 2005

In KSLV-I, actuation system for thrust vector control of kick motor was configured as electro-hydraulic servo actuation system and consisted of actuators, hydraulic power supply system, hydraulic power distribution system and control system. In case of hydraulic power supply system, we use EMDP(Electric Motor Driven Pump) to supply hydraulic power. Generally, we use brushed DC motor for EMDP but it is not easy to operate EMDP using brushed DC motor at a high altitude. Hence, we are developing EMDP using brushless DC motor to use at a high altitude. In this study, we will explain control system for BLDC motor to drive hydraulic pump.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.6
• /
• pp.21-29
• /
• 2008

Korean army currently considers the development of the advanced MLRS(Multiple Launcher Rocket System) as a new alternative, which responses on the renovation of the artillery and future battle field environment. Therefore, This study suggests that the development methods of MLRS based on the analysis of the future battle field environment, world wide development trends of the MLRS and operation states of the domestic MLRS. According to this study, the development methods of new generation MLRS should be included a 230/130mm combined launcher competible with conventional 227mm on the vehicle, advanced FCS(Fire Control System), GPS/INS integration navigation system, Pod of ammunitiom, ammunition carrring vehicle and guided rocket munitions, etc.