• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.4
• /
• pp.463-473
• /
• 2011

The warm shrink fitting process is generally used to assemble automobile transmission parts (shaft/gear). But the fitting process can cause the dimensions of addendum and dedendum of the gear to change with respect to the fitting interference and the profile of the gear. As a result, there may be additional noise and vibration between gears. To address these problems, we analyzed the warm shrink fitting process according to process parameters; the fitting interference between the outer diameter of the shaft and the inner diameter of the gear, the inner diameter of the gear, addendum and dedendum of the gear, the heating temperature. In this study, a closed form equation for predicting the amount of deformation of addendum and dedendum in the R-direction was proposed. And the FEA method to analyze the cooling process was proposed for thermal-structural-thermal coupled field analysis of the warm shrink fitting process (heating-fitting-cooling process).

• Tribology and Lubricants
• /
• v.31 no.4
• /
• pp.170-176
• /
• 2015

As a continuation of Part I, which developed a design formula of the minimum corner radius (R_min) for restraining tribological failures, Part II investigates design parameters such as material properties and contact force. As design examples, Al 7075-T651, SST 304 and HT-9 are chosen for the materials and 1, 10 and 100 kN are used for the forces. The results show that the difference in R_min decreases as either the elastic modulus increases or the contact force decreases. Given the same material and force, the permissible R_min decreases as the flat region increases and vice versa. Because the R_min values obtained from the examples are very small, the dimensions of the corner radius normally designed in engineering structures are regarded acceptable. The von Mises stress evaluated for a typical example, which is far below the yield strength, confirms this interpretation. Nevertheless, the present work can provide a design criterion as well as a guideline for quality control in the manufacturing of, in particular, contact corners, which has not been attempted before to the best of the author’s knowledge. In addition, this paper considers the problem of a step that may be formed in the contact contour by using a similar approach. The result shows that no size of the step is permissible.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.110-113
• /
• 2006

This paper describes the development process of body and full vehicle for reduced idle vibration through the data level of frequency and sensitivity. The vibration mode map is used to separate body structure modes from resonance of engine idle nm and steering system. This paper describes the analysis approach process to reduce the variation of uncertainties for idle vibration performance at initial design stage. The robust design method is performed to increase the stabilization performance under vehicle vibration. It is used to predict the effects of the stiffness deviation according to the spot welding condition of the body structure. The tolerance associated with hood over slam bumper is analyzed for the quality deviation of the moving system in full vehicle. And the glass sealant stiffness and weight difference is considered for the deviation characteristic. The design guideline is suggested considering sensitivity about body and full vehicle by using mother car at initial design stage. It makes possible to design the good NVH performance and save vehicles to be used in tests. These improvements can lead to shortening the time needed to develop better vehicles.

• The Journal of Korea Robotics Society
• /
• v.11 no.4
• /
• pp.248-255
• /
• 2016

Machining error makes the uncertainty of dimensional accuracy of the kinematic structure of a parallel robot system, which makes the uncertainty of kinematic accuracy of the end-effector of the parallel robot system. In this paper, the tendency of trajectory tracking error caused by the tolerance of design parameters of the parallel robot is analyzed. For this purpose, all the position errors are analyzed as the manipulator is moved on the target trajectory. X, Y, Z components of the trajectory errors are analyzed respectively, as well as resultant errors, which give the designer of the manipulator the intuitive and deep understanding on the effects of each design parameter to the trajectory tracking errors caused by the uncertainty of dimensional accuracy. The research results shows which design parameters are critically sensitive to the trajectory tracking error and the tendency of the trajectory tracking error caused by them.

• Journal of the Korea Furniture Society
• /
• v.12 no.2
• /
• pp.1-10
• /
• 2001

As finger joint method has a high rate of yield and high strength and ease in working, it has been widely used as an end joint method for solid wood and wood based-material. Therefore, we end-joined the material of Pinus densiflora, Quercus variabilis and populus euramericana with polyvinyl acetate adhesive and resorcinol phenol resin adhesive. The effect of difference (0, 0.15, 0.3, 0.45mm) between the dimensions of tip width and root width of the finger (DTRW) on bending strength properties was as follows: 1. In the case of polyvinyl acetate adhesive, DTRW had no effect on bending modulus of elasticity(MOE) and modulus of rupture(MOR) of the three kinds of species, because their bonding layers were destroyed by slippage, not their woody parts. 2. In the case of resorcinol phenol resin adhesive, the material of Quercus variabilis showed an optimal result at 0.15 or 0.3 of DTRW, while the poplar did at 0 of DTRW 3. The differences in efficiency ratio of bending MOR of populus euramericana, Pinus densiflora and Quercus variabilis species according to the kind of adhesive were 13-29%, 23-30% and 45-53%, respectively.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.689-692
• /
• 2010

일반형 자동차 내장부품은 외부가 플라스틱 사출 성형한 형태로 사용되지만, 고급 차종은 내장재의 미감이나 질감을 위하여 사출물 표면에 엠보싱 무늬가 형성된 표피재가 수지에 추가로 부착되어 제작된다. 부착하는 방법은 한 장비에서 저압 사출 후 플라스틱이 완전 응고 전에 표피재를 넣고 압입하는 저압 사출법과 표피재 수지를 기 사출된 제품위에 놓고 압착시키는 압착법이 있으나 이 두 방법 모두 엠보싱 무늬가 형성된 표피재를 넣고 작업하기 때문에 고온 압착시 기존 무늬가 찌그러지고 코너 부위가 경화되어 기존의 질감을 얻지 못하며, 치수 공차가 변형되어 불량률이 증가하므로 이를 시급히 개선할 새로운 제조 기술의 필요성이 대두된다. 본 연구는 가열 압착기로 지그 및 금형을 새로 개발하여 도어 트림 제조시, 기 사출물을 금형 쪽으로 기 조직을 삽입한 후 엠보싱 무늬가 없는 원소재 표피재로 상부 금형 쪽으로 소재조직을 진공으로 흡입하여 무늬를 성형한 후 하강시켜, 기 사출물에 압착시키는 가열 압착으로 엠보싱무늬의 손상을 방지하는 금형을 제안하였으며 그에 대한 해석, 설계, 실험을 통하여 성능을 평가 분석 하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.2
• /
• pp.108-113
• /
• 2005

The damageability and repairability of similar platform type vehicles could be very concerned with design optimization. In all the vehicles crash tested, small size passenger vehicles were weakness in aspect of damageability and repairability. The most critical area appears to be repair cost considering that parts cost is the largest portion of total repair cost segments. Besides repair cost, attaching method of front sidemember and subframe are placed special importance for impact energy absorption and damageability and repairability. So in order to improve damageability and repairability of vehicle structure and body component of the monocoque type passenger vehicles, the end of front side member and front back beam should be designed with optimum level and to supply the end of front side member as a partial condition approx 300mm. The effectiveness of design concept on the 40% offset frontal impact characteristics of the passenger vehicle structure is investigated and summarized.

• Journal of ILASS-Korea
• /
• v.25 no.1
• /
• pp.34-39
• /
• 2020

Automotive manufacturers are applying technologies for greenhouse gas reduction such as vehicle weight reduction, engine downsizing, direct injection technology, variable valves and transmission performance improvement to achieve the targets for enhanced greenhouse gas and fuel consumption efficiency. In this paper, compared and analyzed greenhouse emissions according to engine capacity, engine displacement, curb weight and sales volume of hybrid and internal combustion engine passenger vehicles. Hybrid emit 32~39% less greenhouse gas than internal combustion engines through the combined mode test method. Hybrid electric vehicle's curb weight was about 7% heavier on average for the same engine displacement, while greenhouse gas was about 36% lower. It was confirmed that in order to reduce the emission of pollutants of greenhouse gases as well as the air pollutants, it is necessary to expand the supply of eco-friendly vehicles.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.10
• /
• pp.847-852
• /
• 2016

In this paper, important design parameters for parallel kinematic robots are defined, paying special attention to machining errors which may cause kinematic errors at the end effector of a robot. The kinematic effects caused by each design parameter, as well as their upper/lower limits, are analyzed here. To do so, we have developed a novel software program to compute kinematic errors by considering its defined design parameters. With this program, roboticists designing parallel kinematic robots can understand the important design parameters for which upper/lower allowances have to be strictly controlled in the design process. This tactic can be used for the design of high-speed, parallel kinematic robots to reduce the design/manufacturing costs and increase kinematic precision.

• Korean Journal of Optics and Photonics
• /
• v.12 no.4
• /
• pp.276-280
• /
• 2001

The quality of images displayed by using an LC projector is strongly influenced by the cell-gap variations over LC panels, the essential components of the projector. We show that such influence can be relieved by introducing slit patterns in the pixel electrodes in the LC panels. The improvement comes from the compensation of the influence of cell-gap variations by optical anisotropy variations arising from the lateral components of the electric field generated by the slit patterned electrodes. Simulations show that cell-gap tolerance can be increased by more than 50% by introducing the slit patterns. This method can be used in TN mode LC panels, which use LC's with positive dielectric anisotropy. tropy.