• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.224-226
• /
• 2013

본 논문은 유도가열 시스템의 자성체 판별 알고리즘을 제안한다. 코일의 형상 및 구성에 따른 임피던스를 수학적으로 분석하여 자성체와 비자성체 동시 가열을 위한 유도 코일을 능동적으로 설계 한다. 또한 인버터 출력전압과 부하 전류를 센싱하여 계산한 임피던스 값과 수식으로 구한 부하 임피던스를 비교해 가열 용기의 재질을 판별한다. 제안된 알고리즘을 통해 자성체 및 비자성체 유도가열을 하나의 공진형 인버터로 구현할 수 있다. 제안된 판별법은 시뮬레이션을 통해 검증한다.

• Proceedings of the KIPE Conference
• /
• 2015.11a
• /
• pp.35-37
• /
• 2015

본 논문은 전력구 내 지중선에서 발생하는 상용주파수(60 Hz) 자기장을 이용한 2 W급 무선전력 수신장치를 제안한다. 제안하는 수신장치는 자성체와 구리도선을 포함하는 수신 코일, 장치의 개폐를 위한 손잡이, 직렬공진회로 및 정류기를 포함하는 부가회로로 구성된다. 수신장치는 3상 지중선 중 하나에 설치되어 전력구 내 조명 및 온습도 센서를 구동하는데 사용 가능하다. 수신장치의 자성체로는 높은 기계적 강도 및 포화 자속밀도를 가지는 규소강판 박편이 사용되었으며, 직렬공진회로를 사용하여 최대전력을 수신하였다. 수신장치의 공진회로는 3 이하의 낮은 공진계수를 가지기에 50 Hz 및 60 Hz 지중선에 범용으로 사용이 가능하다. 사용된 규소강판 및 구리선의 무게와 가격의 곱을 성능지수(Figure of Merit)로 선정하여 이를 최소화하는 설계를 수행하였다. 제작된 시작품의 무게는 약 750 g중으로 2.2 W LED부하 구동이 가능하며, 이때 지중선의 전류는 $100A_{rms}$로 가정하였다.

• Journal of the Korean Magnetics Society
• /
• v.2 no.1
• /
• pp.69-74
• /
• 1992

This paper describes the energy and speed characteristics of an induction coil-gun. The coil-gun has some merits that it can be easily installed and repeatedly used many times, it does not damage mechanically in the course of launch and the force exerted on the projectile is distributed uniformly. An equivalent circuit is employed for modeling the coil-gun. The circuit equations and equation of motion are then derived based on the equivalent circuit. These equations are solved numerically by using Runge-Kutta method. Finally the energy transfer ratios are obtained according to the variations of the resonant frequency of driving circuit and charging voltage of capacitors. The muzzle velocities of projectile are also obtained according to the variations of electrical conductivity and initial position of projectile, firing angle of driving circuit, charging voltage of capacitor and resistance of driving coil, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.1
• /
• pp.38-44
• /
• 2019

This paper proposes fingerprint-based positioning methods which can be used in a magnetic resonant wireless power transfer(WPT) system and verifies their performance. A new receiver coil with small orthogonal auxiliary coils is proposed to measure magnetic field signals in three axial directions. The magnitude and phase characteristics of the three-axis electromotive force can be obtained by using the proposed coil. To predict a position with the measured values, we propose a lookup table-based method and linear discriminant analysis-based method. For verification, the proposed methods are applied to predict 75 positions of the 6.78 MHz WPT system, and the performances such as accuracy and computation time are compared.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.1
• /
• pp.48-54
• /
• 2002

This paper is described the indirect induction heated boiler and induction heated hot air producer using the voltage-fed series resonant high-frequency inverter which can operate in the frequency range from 20 kHz to 50 kHz. A specially designed induction heater is composed of laminated stainless plates, which have many tiny holes and are interconnected by spot welding. This heater is inserted into the ceramic type vessel with external working coil. This working coil is connected to the inverter and turbulence fluid through this induction heater to moving fluid generates in the vessel. The operating performances of this unique appliance in next generation and its effectiveness are evaluated and discussed from a practical point of view.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.3
• /
• pp.497-502
• /
• 2014

In this paper, a design method for a broadband planar dipole antenna for terrestrial digital television (DTV) reception is studied. The dipole is modified to half bow-tie type for size reduction. The balun between feeding microstrip line and coplanar strip (CPS) line is implemented with a rectangular patch inserted along the center of the CPS line. The proposed antenna is the structure of dual resonances, one is due to the dipole and the other is due to the CPS line attached by the balun. The effects of various geometrical parameters on the antenna performance are examined, and the antenna is designed for terrestrial DTV band (470-806 MHz). The prototype antenna is fabricated on an FR4 substrate with a size of $95mm{\times}178mm$, and tested experimentally to verify the results of this study.

• Journal of IKEEE
• /
• v.25 no.3
• /
• pp.534-539
• /
• 2021

Induction heating method that allows the maximum heating power to be delivered by varying switching frequency in the inductance change of the work coil of induction heater was proposed in this paper. Depending on the type of work piece in the work coil and proximity to the work coil, the resonance frequency of the resonant circuit will be changed. It may be difficult to deliver the maximum power due to the damage of the induced heater element or switching loss depending on the resonance frequency and switching frequency operating relationship. The switching frequency was variable to maintain the maximum power transmission by sensing the heating power due to the change of the resonance frequency. Through the result of the proposed method that can be controlled within the required output change range according to the change of the switching frequency corresponding to the change of the resonance frequency, the induction heater having a variable switching frequency characteristic that can transmit almost constant output power (within 0.43 dB) power efficiency was achieved.

• Journal of the Korean Magnetics Society
• /
• v.22 no.6
• /
• pp.200-203
• /
• 2012

In this study, we have investigated that the operation frequency dependences of the output properties of the orthogonal fluxgate sensor which was fabricated with a ferrite core. An orthogonal fluxgate sensor should be operated in as high as possible frequency to enhance its sensitivity in the case of small sized sensor, because sensitivity of the sensor is proportional to cross section area, winding number and operation frequency. In this study, we investigated the correspondence of the frequency dependence of output and the reactance (inductance and capacitance) of pickup coil and cable. Experimental results represented that we could obtain maximum output (= sensitivity) at optimal frequency which is near LC resonance frequency of the pickup coil and cable.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.24-25
• /
• 2015

본 논문에서는 준랜덤 자속을 사용하는 무선 전력전송 시스템에서 pickup을 위한 공진 회로에 대하여 논한다. 준랜덤 자속은 서로 직교하고 있는 3 개의 코일에 주파수가 다른 3개의 전류를 흘려 얻을 수 있다. 따라서 pickup도 3개의 주파수에 대하여 임피던스가 최저값을 가져야 효과적으로 전력을 끌어낼 수 있다. 즉, 3개의 주파수에 대하여 공진이 발생할 필요가 있다. 본논문에서는 3개의 주파수에서 공진이 일어나는 회로를 제안하고 그 특성에 대하여 논하였다.

• Proceedings of the KIPE Conference
• /
• 2015.11a
• /
• pp.121-122
• /
• 2015

무선 전력 전송에서 자기장을 이용하는 방식은 인덕티브 커플링 방식과 자기 공진 방식이 있다. 자기 공진 방식은 송수신 코일의 크기를 작게 할 수 있고, 인덕티브 방식보다 전력 수신할 수 있는 범위가 넓다. 본 논문에서는 모바일 기기를 위한 자기 공진 무선 전력 전송의 표준 주파수로 유력한 6.78MHz 시스템을 구성하고, 직렬 공진 송신과 병렬 공진 수신을 제안한다. 전자파 노이즈를 억제하기 위하여 LC Low Pass Filter를 추가한 Half-bridge 인버터 송신 회로를 사용하여, 5.5W급 Smart phone 충전을 위한 Prototype을 제작 및 동작과 특성을 검증하였다.