• Journal of Practical Engineering Education
• /
• v.12 no.1
• /
• pp.1-10
• /
• 2020

The pneumatic control circuit is an important basic element that constitutes factory automation in the era of the 4th Industrial Revolution, and the ability to design and fabricate pneumatic control circuit at the university level is one of the most important educational courses. In this study, it introduced collaborative learning by group, and capstone design technique applied to the subject of design and fabricate of pneumatic control circuit. In addition, it intends to contribute to the innovation of practical engineering education by examining the learning achievement of students. It was investigated analytical skill differences by applying cooperative learning to the experimental group and by applying traditional lecture methods to the comparison group. The experimental group that conducted cooperative learning showed higher academic ability than the comparison group that conducted only traditional lectures, and the t-test results of the significant level p<0.05 also confirmed that there were significant differences between the two groups. It was also responded 13 survey questions in four experimental groups and analyzed the results, showing a high satisfaction level of 4.731 on average. Through this study the design and fabrication of the pneumatic control circuit is more effective in improving students' learning achievement when applying the capstone design technique than when operating as a normal subject and expected to use as a basic material for the development of the curriculum of Capstone design in the future.

• Journal of Chest Surgery
• /
• v.41 no.2
• /
• pp.253-259
• /
• 2008

Background: The incidence of cervical esophageal cancer is low compared with that of thoracic esophageal cancer, and the role of surgery for cervical esophageal cancer is limited compared with that of radiotherapy or chemotherapy. This study was carried out to determine the outcome of surgery for cervical esophageal cancer. Material and Method: We analyzed retrospectively medical records of 43 patients who had undergone curative surgical resection for cervical esophageal cancer from January 1989 to December 2002. Follow-up loss was absent and the last follow-up was carried out in February 28, 2004. Result: The mean age was 60 years old and the male to female ratio was 40:3. Histologic types were squamous cell carcinoma 42 patients and malignant melanoma 1 patient. The methods used for esophageal reconstruction were gastric pull-up 32 patients, free jejunal graft 7 patients and colon interposition 4 patients. Postoperative complications occurred in 31 patients (72%), and operative mortality occurred in 7 patients (16%). Pathologic stages were I 3, IIa 14, IIb 1, III 19, and IVa 6 patients. Tumor recurrence occurred in 16 patients (44%), and the 3 and 5-year survival rates were 29.3% and 20.9%. Conclusion: The reported surgical results for cervical esophageal cancer showed somewhat high operative mortality, postoperative complication rates and recurrence rates and a low long-term survival rate. It is suggested that multimodality treatment including surgery is needed for the treatment of cervical esophageal cancer because radiotherapy or chemotherapy without surgery could not relieve dysphagia or resolve the tumor completely.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.227-227
• /
• 2012

Cryopump는 반도체 임플란타 공정, OLED분야, 신소재 개발, 표면분석 및 처리, 의료분야, 입자가속기, 핵융합 등 다양한 진공분야에 응용되는 고진공용 극저온펌프이다. 특히 향후로의 산업구조는 디스플레이, 반도체, IT 산업분야로 집중 재편될 것이기에, 이에 따른 핵심제조장비인 고진공 펌프의 수요가 급증할 것으로 판단된다. 그리고 이를 위한 핵심부품과 장비들의 국산화가 시급한 실정이다. 기술적인 측면에서 보자면 GVT는 미국의 Varian과 일본Ebara의 Cryopump 제조기술을 원천으로 한 회사로써 현재는 국내 유일의 G-M냉동기와 Cryopump 제조기술을 보유한 업체이다. 그리고 최근 오랫동안 정체되었던 관련 기술을 발전시켜 최적화된 한국형 G-M 냉동기 및 이를 장착한 다양한 사이즈의 고성능 Cryopump를 출시하게 되었다. 가장 큰 수확은 Cryopump의 성능을 크게 향상시켰으며 무엇보다 고객맞춤형으로 디자인할 수 있을 정도의 기술력을 확보하게 되었다는 점이다. Cryopump의 성능은 장착되는 Cryocooler(G-M냉동기)의 성능과 밀접한 관련이 있기 때문에 일차로 Cryocooler의 성능을 개선하고 이차로 이를 장착한 Cryopump의 성능을 개선하였다. 본 연구는 일차로 진행된 HP Series 2단 Cryocooler 4가지 모델 중 가장 범용인 HPM 모델과 HPS모델에 대한 제작과 성능시험에 관한 것이다. 이는 각각 기존의 ICP Series 펌프에 장착되던 Expander 535 모델 및 Expander 855 모델에 대한 설계 최적화의 결과물로써 내용은 Cryocooler에 대한 'Typical Performance Test(1st STG와 2nd STG의 온도가 각각의 Stage에 인가되는 Heat Load에 의해 그물망 형태의 그래프가 되도록 수행하는 시험법)'의 절차를 따라 수행되었다. HPM Cryocooler의 성능은 2nd STG Temp. 20K 와 1st STG Temp. 80K를 Heat Load 기준으로 하였을 경우, 각각 8.2W, 55.0W의 성능을 나타내었고 HPS Cryocooler의 성능은 2nd STG Temp. 20K 와 1st STG Temp. 72K를 Heat Load기준으로 하였을 경우, 각각 14.0W, 90.0W의 성능을 나타내었다. 1st STG Temp.를 72K로 정한 이유는 Power Supply의 용량 한계로 인해 90W이상의 Heat Load를 인가할 수 없었기 때문이다. 만약 성능 그래프의 경향성을 고려하여 1st STG Temp. 80K로 가정한다면, 각각 약 13W, 100W 정도의 성능을 가질 것으로 추정된다. 단, 본 시험에 사용된 Compressor는 GVT의 HC80Plus 모델로 내부에는 Helium용 5HP급 Scroll Type의 Compressor가 장착되어 있으며, 봉입압력 250Psig에 저압 100Psig기준, 65scfm의 유량을 가지는 압축기이다. 압축기와 Cryocooler의 조합은 1:1이었고 시험방법은 Cryocooler에 대한 GVT 자체규정에 따라 진행되었으며 밤과 낮 및 공장전체의 부하변동에 따른 냉각수 온도변화에 따른 펌프의 성능변화는 고려되지 않았다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.118-118
• /
• 2012

Cryopump는 반도체 임플란타 공정, OLED분야, 신소재 개발, 표면분석 및 처리, 의료분야, 입자가속기, 핵융합 등 다양한 진공분야에 응용되는 고진공용 극저온펌프이다. 특히 향후로의 산업구조는 디스플레이, 반도체, IT 산업분야로 집중 재편될 것이기에, 이에 따른 핵심제조장비인 고진공 펌프의 수요가 급증할 것으로 판단된다. 그리고 이를 위한 핵심부품과 장비들의 국산화가 시급한 실정이다. 기술적인 측면에서 보자면 GVT는 미국의 Varian과 일본Ebara의 Cryopump 제조기술을 원천으로 한 회사로써 현재는 국내 유일의 G-M 냉동기와 Cryopump 제조기술을 보유한 업체이다. 그리고 최근 오랫동안 정체되었던 관련 기술을 발전시켜 최적화된 한국형 G-M 냉동기 및 이를 장착한 다양한 사이즈의 고성능 Cryopump를 출시하게 되었다. 가장 큰 수확은 Cryopump의 성능을 크게 향상시켰으며 무엇보다 고객맞춤형으로 디자인할 수 있을 정도의 기술력을 확보하게 되었다는 점이다. Cryopump의 성능은 장착되는 Cryocooler (G-M냉동기)의 성능과 밀접한 관련이 있기 때문에 일차로 Cryocooler의 성능을 개선하고 이차로 이를 장착한 Cryopump의 성능을 개선하였다. 본 연구는 일차로 진행된 HP Series 2단 Cryocooler 4가지 모델 중 가장 범용인 HPM 모델과 HPS모델에 대한 제작과 성능시험에 관한 것이다. 이는 각각 기존의 ICP Series 펌프에 장착되던 Expander 535 모델 및 Expander 855 모델에 대한 설계 최적화의 결과물로써 내용은 Cryocooler에 대한 'Typical Performance Test(1st STG와 2nd STG의 온도가 각각의 Stage에 인가되는 Heat Load에 의해 그물망 형태의 그래프가 되도록 수행하는 시험법)'의 절차를 따라 수행되었다. HPM Cryocooler의 성능은 2nd STG Temp. 20K와 1st STG Temp. 80K를 Heat Load기준으로 하였을 경우, 각각 8.2W, 55.0W의 성능을 나타내었고 HPS Cryocooler의 성능은 2nd STG Temp. 20K 와 1st STG Temp. 72K를 Heat Load기준으로 하였을 경우, 각각 14.0W, 90.0W의 성능을 나타내었다. 1st STG Temp.를 72K로 정한 이유는 Power Supply의 용량 한계로 인해 90W이상의 Heat Load를 인가할 수 없었기 때문이다. 만약 성능 그래프의 경향성을 고려하여 1st STG Temp. 80K로 가정한다면, 각각 약 13W, 100W 정도의 성능을 가질 것으로 추정된다. 단, 본 시험에 사용된 Compressor는 GVT의 HC80Plus 모델로 내부에는 Helium용 5HP급 Scroll Type의 Compressor가 장착되어 있으며, 봉입압력 250Psig에 저압 100Psig기준, 65scfm의 유량을 가지는 압축기이다. 압축기와 Cryocooler의 조합은 1:1이었고 시험방법은 Cryocooler에 대한 GVT 자체규정에 따라 진행되었으며 밤과 낮 및 공장전체의 부하변동에 따른 냉각수 온도변화에 따른 펌프의 성능변화는 고려되지 않았다.

• Analytical Science and Technology
• /
• v.18 no.4
• /
• pp.320-328
• /
• 2005

The most common five chlorophenols (4-chloro-3-methylphenol, 2,4,5-trichlorophenol, 2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol, pentachlorophenol) were determined from the industrial wastewater by GC/MS. The samples were collected from the petrochemical company, textile company and leather making company. The developed analytical method was modified by USEPA Method 3510. The samples were extracted with dichloromethane under pH 2 and pH 5-6, and determined by the GC/MS with SIM mode. There were good linearities (above $R^2=0.9943$) on e ranges of the 0.1 ng/mL~10 ng/mL and 0.5 ng/mL~10 ng/mL, and the limit of detection were between 0.1 ng/mL and 0.5 ng/mL. The absolute recoveries were measured at the concentration of 1, 5, and 10 ng/mL, and the recovery was 71.6~98.9% except for PCP. The relative standard deviation (RSD) was 1.2~14.3% and it gave a good reproducibility for the assay. The bias, which shows the accuracy, was a good although it was a little high values (11.3~22.1%) at the low concentration (1 ng/mL).

• Analytical Science and Technology
• /
• v.15 no.3
• /
• pp.196-213
• /
• 2002

The alkylphenols, chlorophenols and bisphenol A were determined by gas chromatography/mass spectrometry-selected ion monitoring mode followed by three work-up methods for comparison; EPA method, isoBOC derivatization method and TBDMS derivatization method. Eleven phenols in water samples were extracted with dichloromethane. Also, solid-phase extraction (SPE) with XAD-4 and subsequent conversion to isobutoxycarbonyl derivatives or tert.-butyldimethylsilyl derivatives for sensitive analysis with the selected ion-monitoring (SIM) mode. The recoveries were 85.1~109.9% (EPA method) and 90.3~126.6% (isoBOC derivatization and TBDMS derivatization), respectively. The method detection limit of bisphenol A for SIM were 0.732 ${\mu}g/{\ell}$ (EPA method), 0.002 ${\mu}g/{\ell}$ (isoBOC derivatization) and 0.021 ${\mu}g/{\ell}$ (TBDMS derivatization). The SIM responses were linear with the correlation coefficient varying 0.9755~0.9981 (isoBOC derivatization), and 0.9908~0.9996 (TBDMS derivatization). When these methods were applied to treated wastewater sample from a polyethylene plant, the concentrations of 11 phenols were below the method detection limit.

• Korean Journal of Environmental Biology
• /
• v.34 no.3
• /
• pp.212-215
• /
• 2016

We developed a new ecotoxicological test method using native test species, eggs of Ephemera orientalis, and five kinds of industrial wastewater were tested to validate the test method. The water samples were collected in Jun 2006 from the following industries: pesticide, metal plating, PCB, leather1, and leather2. Wastewater and effluent were diluted by distilled water, respectively, to prepare various concentrations, 100, 50, 25, 12.5, 6.3, 3.1, and 0%. For the egg bioassay, 20 freshly laid eggs (<24 h old) were exposed to test solutions in a Petri dish ($52{\times}12mm$) at $20^{\circ}C$ with photoperiod of 16 h light and 8 h dark for 14 days. The median egg hatching concentrations (EHC50) were estimated using Probit analysis. All EHC50s of wastewater were less than 3.1%, which meant very high ecotoxicity except for the wastewater of PCB industry having 6.1% of EHC50. Among the effluents, the least toxic effluent was from pesticide industry having 58% of EHC50, while the effluent of leather2 was the most toxic having 7.3% of EHC50.

• Journal of the Economic Geographical Society of Korea
• /
• v.17 no.4
• /
• pp.832-847
• /
• 2014

The main aim of this paper is to contribute to building some strategic foundations for future Korean foreign investors in Cambodia by investigating trends and institutional changes in inward foreign direct investment and working conditions in Cambodia. Rapid increase in labor costs, and investment incentives centering on high-tech industries in China and Vietnam has led to the relocation of labor-intensive industries into low wage countries since the early 2000. As a result, Cambodia has emerged as a new alternative investment region in which enable to off-set existing locational and institutional advantages, so that it has implicated in changes in Asian economic geographies. In addition, the Cambodian government has operated two labor relations projects - Better Factory Cambodia and Labor Dispute Resolution Project - with ILO to improve the working conditions of foreign investment firms. These projects could provide an insight into constructing strategies for foreign investment, and also imply institutional embeddedness in Cambodia.

• Journal of Digital Convergence
• /
• v.15 no.12
• /
• pp.127-136
• /
• 2017

The purpose of this study is to explore some directions and alternatives for reforming the school education system, which is one of the core policy agendas of the Korean society that has met the upcoming 4th industrial revolution era and intelligence information society. Korean school education is a supplier-oriented system that does not take into consideration student's individual needs and aptitudes, and maintains uniform educational and learning practices while strengthening the characteristics of factory school model of the early 20th century. Especially, according to the excessive follow-up of the college entrance examination of the people the de-contextualization of knowledge and the instrumentation and learning of the education has been deepened. For the reform of the education system, first, it should transform the curriculum delegation system from the current administrative to teacher-based system. Second, we need to dismantle the bureaucratic corps of teacher that erodes the autonomy of the teacher and should establish the professional teacher system. Third, we should overcome egoism of each curriculum territory and reform the teacher education system. Fourth, it is necessary to overhaul the system of education and administrative bureaucracy as well as to overhaul the system of educational law. Fifth, it is necessary for the school administration to provide more effective communication between learners and teachers.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.420-429
• /
• 2002

The amount of $CO_2$-silicate bonded waste foundry sand(WFS) occurred in Korea is over 800,000 ton per year. WFS, as a by-product, is generated through manufacturing process of foundry may affect our environmental contamination, The reason is that WFS has been buried itself not less than 90％ out of total WFS. So, it can give damage on the ground of contamination in soil and underwater. Therefore, it is necessary to establish the method recycling WFS because of being intensified waste management law. In this study, we performed the research with respect to harmful component analysis, the qualities of WFS mortar and concrete mixed with WFS. As the results the specific gravity of WFS is the same as that of natural aggregate while unit weight and percentage of solids of WFS are smaller than those of it. But it is found that WFS can be used by substituting WFS for natural aggregate after control of poor grade of WFS. The flowability of mortar and concrete with WFS is inferior to those of natural aggregate, and the setting time of concrete with WFS is faster than that with only natural aggregate, On the contrary, the bleeding of concrete with WFS is shown good result, and compressive and tensile strength of concrete substituted WFS for 30％ are higher than those with only natural aggregate regardless of elapsed time.