• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.573-577
• /
• 2013

Heat pumps come into wide use because high energy efficiency can be obtained and diverse heat sources like geothermal heat, waste heat and air are available. It is necessary for an air source heat pump to defrost in order to remove frost on the surfaces of an outdoor heat exchanger. It is impossible for continuous heating if reverse cycle operation is used as defrosting method, furthermore it causes the degradation of COP. In this study an fin-tube heat exchanger with three rows was used as an outdoor coil. One row among three rows of the heat exchanger was used like a condenser in order to remove frost on it, the others were used as evaporator to accomplish continuous heating. Each row was switched in order from a condenser to an evaporator in specified time interval. Tests were carried out during minimum 180 minutes at the defrost-heating test condition(dry bulb temperature $2^{\circ}C$, wet bulb temperature $1^{\circ}C$) described in KS C 9306. Time-averaged COP was about 20% higher than that of conventional defrosting method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.6
• /
• pp.81-91
• /
• 2013

A novel design process of a parallel multi-flow type air-cooled condenser of a dual-loop waste heat recovery system with Rankine steam cycles for improving the fuel efficiency of gasoline automobiles has been investigated focusing on reduction of the pressure drop inside the micro-tubes. The low temperature condenser plays a role to dissipate heat from the system by condensing the low temperature loop working fluid sufficiently. However, the refrigerant has low evaporation temperature enough to recover the waste from engine coolant of about $100^{\circ}C$ but has small saturation enthalpy so that excessive mass flow rate of the LT working fluid, e.g., over 150 g/s, causes enormously large pressure drop of the working fluid to maintain the heat dissipation performance of more than 20 kW. This paper has dealt with the scheme to design the low temperature condenser that has reduced pressure drop while ensuring the required thermal performance. The number of pass, the arrangement of the tubes of each pass, and the positions of the inlet and outlet ports on the header are most critical parameters affecting the flow uniformity through all the tubes of the condenser. For the purpose of the performance predictions and the parametric study for the LT condenser, we have developed a 1-dimensional user-friendly performance prediction program that calculates feasibly the phase change of the working fluid in the tubes. An example is presented through the proposed design process and compared with an experiment.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.12
• /
• pp.1435-1440
• /
• 2014

This paper was designed to analyze thermal properties using thermoelectric element for air-cooling heat dissipation of 13.2W-class COB LED. For comparative analysis with generally used air cooling methods, the heat sink was designed and produced, and this experiment was conducted to measure the temperature distribution using a contact thermometer while the COB LED was operating for 100 minutes. One result was about $75^{\circ}C$ for the general cooling method, and the other was $57^{\circ}C$ while the thermoelectric element was operating with applying the current of 0.8A to the thermoelectric element. This results confirmed that the method of applying thermoelectric element was much better in the dissipation of thermal condense on the COB LED than that of the general air cooling one. The temperature on the contact points of COB LED using thermoelectric element was decreased about 31% compared with the air cooling method from $75^{\circ}C$ to $57^{\circ}C$.

• Transactions of the KSME C: Technology and Education
• /
• v.2 no.1
• /
• pp.57-63
• /
• 2014

In this paper new air-cooling system utilizing Stirling engine was proposed for improving efficiency in solar photovoltaic power generation. The solar cell plate was equipped with semi-circular channel for air flow on the backside. Beta-type Stirling engine was installed on the plate and its flywheel was connected to a motor fan by a transmission belt. A forced convective air flow for heat radiation was generated by the operation of the self-starting Stirling engine. The performance tests for power generation of solar cell with or without the proposed air-cooling system were conducted under halogen lamp. From the experimental results, it was found that decline in output voltage of the solar cell with proposed cooling system was 25% less than that of the solar cell without cooling system.

• Journal of the Korea Society of Computer and Information
• /
• v.20 no.4
• /
• pp.11-16
• /
• 2015

Data center, not only the development of globally of cloud-based IT solutions, As the big data, education, use of development electronic equipment of communication means is increased, Demand of domestic and international data center has increased steadily. Due to the increase of data center demand, heat generation of server rack due to the development of IT equipment is also increasing continuously. Calculating heat value of the data center, because more than 99% of the power usage of IT server is converted into heat, the calorific value as the size and capacity of the server is larger will increase. In this paper, to center the cooling system of air-cooled, and research and development of air conditioning systems for energy reduction of data center, through performance analysis and simulation, it has been analyzed that there is energy savings.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.519-519
• /
• 2013

본 연구에서는, 전기적 충격이 없고 넓은 면적을 동시에 처리할 수 있는 형태의 유전체 장벽 방전(DBD: Dielectric Barrier Discharge)을 이용한 대기압 저온 플라즈마 장치를 제작하고 이를 이용하여 빵 곰팡이(Neurospora crassa) 살균에 대한 기본 분석을 하였다. 실험에 사용한 저온 대기압 면방전 플라즈마의 파워는 사인파 교류전압을 인가하여, 방전전압은 1.4~2.3 kV, 방전전류는 20~30 mA의 값을 가지며, 전압과 전류의 위상차는 약 80도의 기울기 차이가 난다. 이때의 출력은 약 4 W를 가지며, 공랭식 쿨러를 이용하여 유전체의 열을 배출하였다. 시료대의 온도 측정결과 방전과 동시에 쿨러를 작동할 경우 최대 10분에서 37도를 넘지 않았다. 장치에서 발생하는 플라즈마에 의한 O3의 양은 플라즈마 발생부로부터 10 mm 이내에서 약 25~30 ppm 이 측정되었으며, NO나 NO2 는 거의 검지되지 않았다. 증류수(Deionized water)속에 담긴 빵 곰팡이(Neurospora crassa) 포자를 면방전 플라즈마 발생장치로 처리하였을 때, 포자의 발아율은 처리시간 및 출력파워가 증가함에 따라 급격히 감소하였으나 VM (Vogel's Minimal) 배양액에 넣고 플라즈마 처리를 한 경우에는, 증류수의 결과와 달리 살균효과가 미비함을 보였다. MTT 측정법 또한 같은 경향성을 보였으며, 이를 통해 포자를 둘러싸고 있는 환경이 플라즈마의 살균효과에 영향을 미치는 것으로 보인다. 본 실험을 통해, 유전체 장벽을 이용한 면방전 플라즈마 발생장치가 플라즈마 제트(jet)와 달리 직접적인 플라즈마 접촉 없이도 미생물 살균이 가능하다는 것을 보았으며, 처리대상의 생체용액과 같은 주변 환경에 영향을 받음을 알 수 있었다. 또한 면방전 플라즈마 장치로부터 발생하는 O3과 같은 활성종들이 빵 곰팡이의 비활성화에도 역할을 할 수 있음을 알 수 있었다.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.26 no.1
• /
• pp.39-45
• /
• 2018

Research on FA(Fly ash) is actively carried out, while the research on BA(Bottom ash) is not so, and research on BA recycling field is urgently required. Therefore, in this study, we investigated the lightweight and thermal insulation characteristics of BA mortar by comparing BA mortar made with porous dry BA(air-cooled) and general mortar. To investigate the lightweight of BA, density test, unit volume mass test and SEM(Scanning Electron Microscope) test were performed. BA mortar and general mortar molds were prepared for the thermal insulation test at room temperature and humidity environment determined by KS A 0006 and they were dried at the temperature of $105{\pm}2^{\circ}C$ until the weight became constant. As a result of the lightweight test, the lightweight of BA mortar is about 30% lighter than the general mortar. Therefore, BA is expected to contribute to reduce the building load when used as building material. As a result of thermal insulation test, the thermal conductivity of BA mortar is about 30% better than that of general mortar.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1003-1010
• /
• 2013

In this study, a simulation program was developed, which predicts the performance of cold-air forced circulation type air cooled showcase. The showcase has an excellent display effect in addition to preserving the grocery. In the program, the compressor was analyzed using performance data supplied by the manufacturer and the capillary tube pressure drop was analyzed using a homogeneous model. The evaporator and condenser were analyzed by dividing the heat exchangers into small elements, where energy balance and appropriate heat transfer correlations were used. A showcase model with two 3/4 HP compressors, capillary tubes of 1.6 mm inner diameter, a fin-and-tube evaporator and condenser was tested, and the results are compared with the predicted values. It is shown that both evaporation and condensation temperatures are adequately predicted by the program.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.2545-2552
• /
• 2014

This study is aiming to suggest the effective thermal management system design technologies for the high voltage and capacity battery system of the electricity driven vehicles and introduce the theoretical designing methods. In order to investigate the effective operation of the battery system for the electricity driven vehicles, the heat generation model for Li-ion battery system using the chemical reaction while charging and discharging was suggested and the thermal loads of the heat sources (air or liquid) for cooling and heating were calculated using energy balance. Especially, the design methods for the cooling and heating of the battery system for maintaining the optimum operation temperature were investigated under heating, cooling and generated heat (during charging and discharging) conditions. The battery thermal management system for the effective battery operation of the electricity driven vehicles was suggested reasonably depending on the variation of the season and operation conditions. In addition, at the same conditions under summer season, the cooling method using the liquid and active cooling technique showed a relatively high capacity, while cooling method using the passive cooling technique showed a relatively low capacity.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.17 no.3
• /
• pp.30-40
• /
• 2021

This paper compares the annual energy performance of four different types of air-conditioning systems in a medium-sized office building. Chiller and boiler, air-cooled VRF, ground-source VRF, and ground-source heat pump systems were selected as the systems to be compared. Specifically, the energy performance of the GSHP system and the ground-source VRF system were compared with each other and also with conventional HVAC systems including the chiller and boiler system and air-cooled VRF system. In order to evaluate and compare the energy performances of four systems for the office building, EnergyPlus, a whole-building energy simulation program, was used. The EnergyPlus simulation results show that both the GSHP and the ground-source VRF systems not only save more energy than the other two systems but also significantly reduce the electric peak demand. These make the GSHP and the VRF systems more desirable energy-efficient HVAC technologies for the utility companies and their clients. It is necessary to analyze the impact of partial load performance of ground-source heat pump and ground-source VRF on the long-term (more than 20 years) performance of ground heat exchangers and entire systems.