• 한국추진공학회지
• /
• 제23권1호
• /
• pp.124-131
• /
• 2019

가스터빈엔진 고도시험설비 운용특성탐색 및 설비튜닝 연구와 유량/추력 측정방안 검증을 위한 엔진 시뮬레이션덕트 설계 연구를 수행하였다. 설비 운용특성 검증은 배압/추력 제어가 필요하므로 Spikecone type의 가변노즐을 적용하였으며, 유량검증용 ISO 쵸킹노즐의 추가장착이 가능토록 설계하였다. 시뮬레이션덕트 주유로 면적은 1D Sizing으로 결정하고, 노즐면적변화에 따른 시뮬레이션덕트 내부 유동특성은 1D/CFD 해석으로 조사하였으며, 해석결과로부터 설비운용특성 탐색 및 유량/추력 검증시험을 위한 공기공급부 시험조건을 도출하였다. Spike 노즐 구동부는 시험 전운용 구간에서 공력하중조건을 견디도록 모터, 리니어 볼스크류 등의 부품모델을 선정하였으며, 시험 시 10 mm/s의 이송속도가 가능하도록 설계하였다.

• 한국자동차공학회논문집
• /
• 제13권3호
• /
• pp.10-16
• /
• 2005

Recently, the international regulations about the exhaust emissions of the motorcycle have been strengthened. The electrically controlled fuel injection type motorcycle has been emphasized to meet with this regulation. However, since the pulsation phenomenon happens in the intake port of the motorcycle because of the characteristic of high speed and the smaller layout than the passenger car, there are many difficulties to select the factor about control parameters needed to develop the ECU system. In this paper, the pulsation values measured from the engine test were compared with the calculated one by WAVE, and it was analyzed the pulsation characteristic according to the driving condition and estimated the mass flow rate. This research showed that the lowest point of the pressure gets lowin the low load and the pulsation of pressure were increased in the high load. Also, the simulation program was verified by showing good prediction of the pulsation and air mass flow rate.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.102.1-102.1
• /
• 2010

바이오매스(Biomass)는 지구상에서 에너지원으로 이용될 수 있는 모든 식물과 미생물을 총칭하는 의미로 사용된다. 최근 바이오매스를 에너지자원화 시키는 방법으로 주목받는 열화학적 전환(Thermo-chemical conversion) 반응은 산소가 없이 혹은 희박한 조건에서 바이오매스에 열과 압력을 가하거나 공기나 수증기 등의 가스화제와 반응하여 바이오오일(Bio-oil) 및 합성가스(Syngas)로 변화하는 프로세스를 의미한다. 바이오매스로부터 바이오 DME(Di-Methyl Ether) 생산을 위한 합성가스를 제조하기 위해서 국내 산림자원을 대상으로 열분해반응 특성연구를 수행하였다. 또한 이들 물질로부터 바이오 DME 합성을 위해 최적의 합성가스 제조를 위한 타당성 연구를 수행하였다. 반응온도 $800{\sim}900^{\circ}C$에서 가스화 수율은 78~80%, 촤 수율은 17~20%, 타르 수율은 4~10%였고, 합성가스($H_2$/CO)비는 0.9~1.6였다.

• 대한기계학회논문집
• /
• 제18권3호
• /
• pp.662-669
• /
• 1994

In the combustion system, the optimum spray conditions reduce the pollutant emission of exhaust gas and enhance the fuel efficiency. The spray characteristics-the drop size, the drop velocity, the number density and the mass flux, become increasingly important in the design of combustor and in testifying numerical simulation of spray flow in the combustor. The purposes of this study are to clarify the spray characteristics of twin-fluid nozzle and to offer the data for combustor design and the numerical simulation of a spray flow. Spatial drop diameter was measured by immersion sampling method. The mean diameter, size distribution and uniformity of drop were analyzed with variations of air/liquid mass flow ratio. The results show that the SMD increases with the liquid supply flow rate and decreases with the air supply velocity. The radial distribution of SMD shows the larger drops can diffuse farther to the boundary of spray. And the drop size range is found to be wider close to the spray boundary where the maximum SMD locates.

• 한국전산유체공학회지
• /
• 제11권3호
• /
• pp.22-27
• /
• 2006

Flow around a guided missile in high maneuver, i.e. at a high angle of attack, shows complex phenomena. It is well known that even in geometrically symmetric conditions the flow around a missile at high angles of attack can generate unexpected large side forces and yaw moments due to asymmetric vortices. In this paper, a CFD code (FLUENT) based on the Navier-Stokes equations was used for the numerical analysis to find a suitable numerical mechanism for generation of asymmetric vortices. It is shown that a numerical technique of applying different surface roughness to a specific area of the missile nose surface gives the best fit in comparison with the experimental results. In addition, a numerical investigation of variations of side forces and pressure distributions with angle of attack and roll angle was conducted for the purpose of identifying the source of vortex asymmetries.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.137-142
• /
• 2002

The fluid mechanics and operating conditions of gas-lubricated proceeding bearings in micro rotating machinery such as micro polarization modulator and micro gas turbine are different from their larger size ones. Due to non-continuum effects, there is a slip of gas at the walls. Thus in this paper, the slip flow effect is considered to estimate the pressure distribution and load-carrying capacity of micro gas-lubricated proceeding bearings as the local Knudsen number at the minimum film thickness is greater than 0.01. Based on the compressible Reynolds equation with slip flow, the static characteristics of micro gas-lubricated proceeding bearings are obtained. Numerical predictions compare the pressure distribution and load capacity considering slip flow with the performance of micro proceeding bearings without slip f]ow for a range of bearing numbers and eccentricities. The results clearly show that the slip flow effect on the static characteristics is considerable and becomes more significant as temperature increases.

• 한국연소학회지
• /
• 제4권1호
• /
• pp.49-57
• /
• 1999

An experimental study on double-concentric diffusion flame has been carried out in order to investigate the shape, the flame length, and the other characteristics of the flame. Flow visualization of the flame by the $TiO_2$ particles and also the emission measurements are conducted. The commercial grade LP gases are used as fuel. The inverse diffusion flames are formed at the center when the central air flow rate is about 0.1 L/min. With a larger flow rate of the central air jet than 0.2 L/min the flame turns to be an annular-shaped flame, which is very bright. When the central air flow rate increases over 2.4 L/min, the flame turns to blue and the flame tips are opened because of the lifting of the inner part of the flame. Because of this lifting and the incomplete combustion, the CO emission increases abruptly from 25 ppm to more than 150 ppm. On the contrary, the NOx emission is decreased.

• 한국산학기술학회논문지
• /
• 제13권9호
• /
• pp.3827-3834
• /
• 2012

최근 많은 열에너지를 필요로 하는 열풍식 건조기 대신 에너지 효율이 높은 히트펌프 건조기가 제지, 섬유, 목재, 식품 등 다양한 분야에서 사용되고 있다. 본 논문에서는 냉동 농산물 건조 초기에 전기히터 사용을 최소화하여 에너지 효율을 높이고자, 압축기 출구 고온가스 우회 시스템에 대한 히트펌프 사이클 특성을 이론적으로 고찰하였다. 또한, 추가 열을 확보하기 위하여 외부공기 유입을 위한 댐퍼를 고려하였고 이의 최적화를 통해 에너지 효율 향상이 가능함을 보였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권8호
• /
• pp.862-869
• /
• 2005

A study on convective cooling characteristics has been done in the channels with heat pipes and associated Plane fins Analysis with FLUENT V5.0 lies its Purpose on the possible enhancement of heat transfer capability between an existing three in-line arrayed heatpipes and an extending four in-line arrayed heatpipes with increasing channel width. Numerical analysis is limited to the laminar flow in an isolated flow channel by employing cyclic boundary conditions for calculation purposes. Friction factors for three and four in-line arrayed heatpipes are compared with experimental results. In addition, temperature behavior at the plate fin for the three in-line arrayed heatpipes is compared with experiment. Friction factors and overall channel heat transfer coefficients (and/or Nusselt numbers) are presented as a function of Reynolds number. An increase of number of heatpipes and channel width reults in a decrease of the friction factor and doesn't not result in an increase of heat transfer performance. However. considering the 25$\%$ increase of heat load accompanies with maximum 8$^{\circ}C$ rise of average temperature of heat pipes, the four in-line array with the increase of channel width of heat pipe heat sink can be considered appropriate.

• 대한기계학회논문집B
• /
• 제24권10호
• /
• pp.1285-1293
• /
• 2000

In port fuel injection system of SI engines, injected fuel is impinged onto the surface of intake valves and port-wall, and then formed the wall flow under the cold start operation. Wall flows entrained into the cylinder result in the unsteady and nonuniform mixture formation. Therefore, the spray impingement to the wall is considered as having negative influences such as lowering combustion efficiency and causing unburned hydrocarbon emissions. This study investigates the spray characteristics of the wall impinging air-assist spray in suction air flow. A PDPA was used to analyze the flow characteristics under the different conditions such as impingement angle and supplied air. Experimental data concerning the impinging sprays has been obtained in the vicinity of the wall. Measured droplets divided into the pre-impinging droplets which denote as the positive normal velocities and post-impinging droplets that describe as the negative normal velocities for the suction flow. Their velocities, size distributions and SMD are comparatively analyzed before and after the impingement.