• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.2
• /
• pp.54-62
• /
• 2010

This paper describes the development of high fidelity air data processing algorithm which can be applied into an air data system for a high speed aerial vehicle. Unlike the previous air data system, current algorithm used several pre-determined pressure data which were obtained with computational fluid dynamic approach without using total pressures having enough sensor redundancy and fault detection ability. The verification of current algorithm was done by commercial software Matlab and Simulink.

• Aerospace Engineering and Technology
• /
• v.7 no.1
• /
• pp.40-48
• /
• 2008

Air mixing system which is composed of air pressure control system, hot pipe system and air mixer, is the facility for mixing hot air($1000^{\circ}C$, 10kg/s) from storage air heater (SAH) and decompressed air($20^{\circ}C$, 15kg/s) from high pressure air supply system. Air pressure control system reduce the pressure of the air, from 32MPa to 3.5 MPa and supply the decompressed air to air mixer. The hot pipe system supply hot air from SAH to air mixer which mix hot with the decompressed air from air pressure control system. Fully mixed air flow rate is 25kg/s and mixed temperature is up to $400^{\circ}C$. So, we can expand the operating envelop of the supersonic ground test facility to low Mach number and low altitude region.

• Journal of Bio-Environment Control
• /
• v.1 no.1
• /
• pp.72-83
• /
• 1992

우리 나라 축사는 생산효율 제고를 위하여 대형화, 밀폐화, 고밀도화, 자동화 경향이 뚜렷하다. 대형의 밀폐된 고밀도 축사는 쾌적한 실내환경을 전제로 하기 때문에 기계적으로 실내환경을 적절히 제어하지 않으면 안된다. 제한된 공간에 먼지, 병원성 미생물, 유해기체, 수분이나 열의 과도한 집적은 생산과 재생산효율에 심각한 영향을 미친다. 그러므로 축사내 생산주체인 가축과 작업인이 쾌적한 실내환경에서 생산활동을 할 수 있도록 열적, 화학적/생물학적 환경을 물리적으로 제어하지 않으면 안된다. 본 연구는 실험축사내 가축이 일정한 열을 발생할 때 실내공기의 유동형태를 예측하기 위해서 수행하였다. 이 연구의 결과를 실내환경제어를 위한 환기시스템 책략 개발의 기초자료로 활용할 수 있다. 실험축사내의 공기유동을 예측하기 위해 Body-Fitted Coordinate(BFC)의 격자배열과 k-$\varepsilon$ 난류모형 및 SIMPLE계열 solution scheme을 사용하였으며, 예측의 유효성 검정은 Boon(1978)의 실험결과를 이용하였다. 예측한 공기유동의 형태와 실험한 공기유동의 형태를 비교한 결과 대체로 만족할만한 결과를 얻었다. 그러나 유입공기의 온도가 1$0^{\circ}C$인 경우의 공기유동은 실험유동형태와 약간의 차이가 있었다. 즉, 실험에서는 수평슬롯으로 유입 된 공기가 바로 아래로 굴절되어 유동하였으나, 예측의 결과는 일정 거리로 수평방향으로 유동하다가 아래로 굴절하였다. 이런 유동의 차이는 k-$\varepsilon$ 난류모형 자체가 경험적으로 부력에 민감하게 반응않는 결함이 원인이 될 수도 있으며, 실험의 부적절한 수행이 원인이 될 수도 있다. 이 유동의 경우 Reynolds 수가 3,000정도의 난류이며, 완전발달유동 (fully-developed flow)이므로 관성력 (inertia force)이 부력 (buoyancy force)보다 커, 일정거리 수평으로 유동하다가 아래로 굴절할 수도 있기 때문이다. 앞으로 이를 규명하기 위한 보다 깊이 있는 연구가 이루어져야 할 것이다.

• Journal of Biosystems Engineering
• /
• v.14 no.2
• /
• pp.123-127
• /
• 1989

축사나 환기시스템은 슬롯 환기시스템(slot-ventilation systems)으로 설치되어 있는 경우가 많으며, 이의 공기 유동(流動)을 2차원으로 해석할 수 있다. 직사각형 슬롯 환기 밀폐공간의 공기혼합 형태와 속도분포의 추정을 위해서 K-E 난류 전이모형을 기초로 한 TEACH-T 프로그램을 변형, 적용하였다. 이 모형을 이용하여 얻은 기류분포 형태는 실측한 기류분포 형태와 매우 잘 맞았으며 추정한 공기속도의 크기는 비교적 잘 맞는 편이었다. 그러므로 TEACH-T 프로그램을 변형해서 환기시스템 설계의 기초자료가 되는 여러 형태의 슬롯 밀폐공간의 공기분포와 공기속도의 크기를 추정하는데 TEACH-T 프로그램을 변형해서 적용시킬 수 있다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.10
• /
• pp.865-871
• /
• 2014

This study was conducted with the aim of developing a venturi-type air supply system for a microbubble generator. In order to determine the influence of the varying geometry of the venturi tube on the flow characteristics, a computational fluid dynamics (CFD) simulation was performed using the commercial CFD software ANSYS CFX-15. Furthermore, in order to elucidate the effects of variation in major design dimensions such as the air supply hole size, position of holes, and number of holes on the air supply characteristics, two-phase multiflow CFD analysis was performed. The analysis results showed that the starting point of expansion on the venturi tube with 0.75 is the best hole position and that the air supply hole size and the number of holes are linearly proportional to the amount of air.

• Journal of Energy Engineering
• /
• v.11 no.4
• /
• pp.306-316
• /
• 2002

ln this paper, flowfields inside the various rooms have been investigated. A storage room, a liv-ingroom with a kitchen in an apartment, and a hospital room are considered in the present calculations. In all cases, it was found that the average of air change rate is. similar to that of perfect mixing assumption and the location of air purifier has little effects on the average air change rate. Detailed local air concentrations show that there are regions where air is not quite purified because of non-uniform circulation of air flow. The location of air purifier has great effects on this behavior.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.2
• /
• pp.46-56
• /
• 2013

The test facility with hot-air supply system is required to develop transpiration cooling materials and experimentally evaluate its performance. In the study, the facility consists of an arc-plasma generator, plenum chamber suppling cold air, and test section was designed and an internal flow analysis was executed. From CFD results, it was confirmed that the designed plenum chamber thermally safeties and ideally mixes with plasma gas and cold air in the chamber. In addition, validity of design for supplying homogeneous flow to the test section was confirmed by this analysis.

• Journal of Bio-Environment Control
• /
• v.28 no.1
• /
• pp.16-27
• /
• 2019

Using virtual reality technology, users can learn and experience many interactions in virtual space like the actual physical space. This study was conducted to develop air flow simulator that allows farmers and consultants to consult air flow through VR devices by creating a greenhouse or pigpen model. It can help educate farmers about the importance of ventilation effects for agricultural facilities. We proposed CFD visualization system by building a virtual reality environment and constructing database of CFD and structure of agricultural facilities. After consultants can set up situations according to environmental conditions, the users experience the visualized air flow of agricultural facility according to the ventilation effects. Also it can provide a quantified environmental distribution in the agricultural facility. Currently, the CFD data in agricultural facilities are established during winter and summer. In order to experience various environmental conditions in the developed system, The experts need to run CFD data under various environmental conditions and register them in the system requirements.

• Journal of Integrative Natural Science
• /
• v.15 no.2
• /
• pp.73-81
• /
• 2022

본 연구는 다중이용시설 이용자들의 쾌적함과 안전 그리고 시설내부 에너지 사용량의 최적 절감을 위하여 이용자수를 분석예측한 정보에 따른 공기질품질제어시스템 운영을 통해 국민 중심의 안전하고 쾌적한 서비스를 제공할 필요로 수행되었다. 이를 위하여 실내유동인구수를 카운팅하는 로컬시스템을 제작하고 수집된 유동인구 카운팅 정보를 시계열 모델링을 기반으로 분석예측하는 연구를 진행하였다. 개발된 시스템 성능평가 결과 유동인구 카운팅시스템은 95% 이상 정확도를 보여주었고, 예측시스템은 83~95% 정확도를 확보하였다. 본 연구결과 개발된 시스템은 다중이용시설에 즉시 적용가능하며 향후 남녀노소 인식을 진행하고 이를 예측한 정보에 의한 보다 다양한 서비스 개발을 추진할 계획이다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.470-476
• /
• 2019

The braking force for a train is generally provided by compressed air. The pressure valve system that is used to apply appropriate braking forces to trains has a complex flow circuit. It is possible to make a channel shape that can increase the flow efficiency by 3D printing. There are restrictions on the flow shape design when using general machining. Therefore, in this study, the compressed air flow was analyzed in a pressure valve system by comparing flow paths made with conventional manufacturing methods and 3D printing. An analysis was done to examine the curvature magnitude of the flow path, the diameter of the flow path, the magnitude of the inlet and reservoir pressure, and the initial temperature of the compressed air when the flow direction changes. The minimization of pressure loss and the uniformity of the flow characteristics influenced the braking efficiency. The curvilinear flow path made through 3D printing was advantageous for improving the braking efficiency compared to the rectangular shape manufactured by general machining.