• Journal of Energy Engineering
• /
• v.9 no.4
• /
• pp.348-357
• /
• 2000

본 연구에서는 동해화력 순환유동층 보일러와 유사한 3개의 사이클론을 갖는 직사각형 구조의 순환유동층 반응기를 이용하여 동해화력 운전조건 -연소로 공기 속도, 일-이차 공기비, 전체 고체량(inventory), 입도 및 입도분포 등- 에 따른 축방향 고체 체류량 및 순환량 등의 수력학적 특성을 고찰하였다. 상승관에서의 공기유속(U$_{0}$)이 증가함에 따라, 또는 PA/[PA+SA]비가 증가함에 따라, 그리고 전체 고체량(inventory)이 증가함에 따라 고채 채류량 및 순환량은 증가하는 것으로 나타났다. 또한 넓은 입도 분포를 갖는 석탄 회재의 경우는 균일한 입도 분포의 입자들에 비해 입자 비산량 및 고체 순환량이 작을 것으로 나타났다. 한편, 층내에서의 고체 체루량 분포를 감소지수 a 및 K를 사용하여 나타낼 수 있었으며, a 및 K와 유속 및 입자간의 상관 특성치를 도출하여 유동 및 순환특성을 고찰하였다. 상기의 상관수는 균일한 입도의 모래에 비해 석탄회재가 비교적 큰 값을 나타내었으며, 상관수가 클수록 희박상 영역에서의 비산 및 고체 순환량이 작은 것으로 나타났다.다.

• Journal of Bio-Environment Control
• /
• v.18 no.3
• /
• pp.215-224
• /
• 2009

A survey on the actual state of heating, cooling, ventilation, and air-flow and experimental measurement of temperature and humidity distribution in tomato greenhouse were performed to provide fundamental data required in the development of air-flow control technology. In single-span plastic houses, which account for most of 136 tomato greenhouses surveyed, roof windows, ventilation and air-flow fans were installed in a low rate, and installation specs of those facilities showed a very large deviation. There were no farms installed greenhouse cooling facilities. In the hot air heating system, which account for most of heating type, installation specs of hot air duct showed also a large deviation. The exhaust air temperature and wind speed in hot air duct also were measured to have a big difference depending on the distance from the heater. We are using the maximum difference as indicator to determine whether temperature distribution is uniform. However if the temperature slope is not identical in greenhouse, it can't represent the uniformity. We analyzed relation between the maximum difference and the uniformity of temperature and humidity distribution. The uniformity was calculated using the mean and standard deviation of data from 12 measuring points. They showed high correlation but were represented differently by linear in the daytime and quadratic in the nighttime. It could see that the uniformity of temperature and humidity distribution was much different according to greenhouse type and heating method. The installation guidelines for ventilation and air-flow fan, the spread of greenhouse cooling technology for year-round stable production, and improvement of air duct and heating system, etc. are needed.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05d
• /
• pp.88-94
• /
• 1996

원자력발전소의 공조계통에 설치되어 운영되는 기체 방사성물질 제거용 첨착 활성탄 탑내에서 균일한 공기 유속분포가 유지되고 있는지를 확인하기 위한 실험을 실시하였다. 본 실험에 사용되는 장비(Tester for Flow Distribution, 이하 TFD라 함)는 원자력발전소에서 사용하는 첨착 활성탄 필터(Adsorber)내의 흡착층을 모방하여 자체에서 제작하였으며, 시험조건들은 실제의 값을 기준으로 적용하였다. 각 위치에서의 보정된 용적 유속을 구하기 위해 자체에서 만든 "FLOWD"라는 계산프로그램을 사용하였으며, 입구 및 출구측 공간에 10" 간격으로 각 6개씩 유속 감지기를 설치하여 면속도를 구하였다. 각 지점에서의 면속도는 평균 0.24449m/s로 각 구간에서의 겉보기 면속도의 분포는 매우 균일한 값을 나타내었으며, 약 2% 이내의 편차로 활성탄 탑내에서의 공기의 흐름이 균일하게 통과함을 확인할 수 있었다.통과함을 확인할 수 있었다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.9-9
• /
• 2000

액체 램제트 엔진의 V형 유입구에 3개의 안내깃이 있은 경우에 대하여 유동 해석을 수행하였다. 수치해석에 앞서 본 연구에서는 ONERA에서 발표한 고체 램제트 연소기에 대한 실험 결과를 유동 해석 결과와 비교하여 해석의 정확성을 검증하였다. 안내깃에 의하여 연소실로 유입되는 공기는 유입구 곡관에서 효율적인 흐름을 유지할 수 있고 분사되는 연료의 분포도 제어될 수 있다. 안내깃의 두께가 큰 경우 자칫 유입되는 공기의 흐름을 방해하는 장애물의 역할을 할 수 있으므로 두께의 변화에 대한 영향도 계산하였으나 선정된 안내깃에 의한 연소실에서의 유동특성 변화는 적은 것으로 나타났다. 입구조건을 균일 유동으로 주고 해석한 결과, 연소실에서의 유동은 안내깃의 유무에 따라 큰 영향을 받지 않았다. 그러나 흡입구로 유입되는 공기의 속도 분포는 다양한 비행조건에서 균일하지 않기 때문에 주 유동을 방해하지 않는 안내깃의 설치는 연소실에서의 좀 더 안정된 화염의 생성을 위해 필요하다.

• Nuclear Engineering and Technology
• /
• v.10 no.2
• /
• pp.79-86
• /
• 1978

The object of this study was to obtain data on air-distributions in two-phase up flow in vertical rod-bundle test-section. The test-section in this study was a hexagonal shaped 61-rod bundle where each rod was wrapped with helical spacers. The variables were flow rates of air and water and air inlet positions. Experimental data were obtained at the outlet of the test-section. The experiments were performed in two parts. Firstly, data were taken at increasing flow rates of air keeping water flow rates constant, and secondly, at simultaneous increase of air and water flow rates. At each flow condition, air supply position could be changed to 4 different positions. Data obtained by electrical void-needle technique were analyed and are presented here in graphical forms for comparison. The results of this study demonstrate qualitatively that air-distribution tends to be more uniform as water flow rates are increased. The air supply positions have noticeable effects on the pattern of air-distribution.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.31-36
• /
• 2010

SAI(Secondary Air Injection) system has been studied widely as one of the promising countermeasure for reducing HC emission at cold start. In this paper, in order to find out the optimal position of SAI, computational thermal fluid analysis on exhaust system adapted SAI system is performed using commercial 3-D CFD code, CFX. The present results showed that SAI position strongly affected the uniformity of air distribution in front of catalyst. And also through the decision process of optimal position of SAI, new index, uniformity of air distribution($U_{\phi}$) is proposed to define it quantitively. Because $U_{\phi}$ is very simple equation and similar with flow uniformity, it is very easy to figure out the physical meaning and to apply it to practices. Finally, we applied the index $U_{\phi}$ to the decision process of the optimal position of SAI, so that we could get the clear comparison results.

• Journal of the Korean Institute of Gas
• /
• v.23 no.3
• /
• pp.20-26
• /
• 2019

Selective catalytic reduction(SCR) method is widely used among various methods for reducing nitrogen oxides in combustion devices of coal power plant. In the present study, the computational fluid dynamic analysis was accomplished to derive the optimal shape of ammonia-dilution air mixing device in a ammonia injection grid. The distribution characteristics of flow and $NH_3$ concentration had been elucidated for the reference shape of ammonia mixing device(Case 1). In the mixing device of Case 1, it could be seen that $NH_3$ distribution was shifted to the wall opposite to the inlet of the ammonia injection pipe. For the improvement of $NH_3$ distribution, the case(Case 2) with closing one upper injection hole and 4 side injection holes, the case(Case 3) with installing horizontal plate at the upper of ammonia injection pipe, the case(Case 4) with installing horizontal plate and horizontal arc plate at he upper of ammonia injection pipe were investigated by analyzing flow and $NH_3$ concentration distributions. From the present study, it was found that the % RMS of $NH_3$ for Case 4 was 4.92%, which was the smallest value among four cases, and the range of $R_{NH3}$ also has the optimally uniform distribution, -10.82~8.34%.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.4
• /
• pp.51-57
• /
• 1999

Temperature and velocity controlling of air at inlet position of Ramjet combustor is important under Ramjet engine grounding-test condition since temperature of inlet air increases due to compression process by supersonic flow at inlet position of Ramjet combustor. In this study, Vitiated Air Heater methodology was used to control temperature of air that is inducted into Ramjet combustor. Temperature and velocity of air at Vitiated air heater exit, which is inducted into Ramjet combustor, were measured to evaluate Vitiated air heater system developed in this study. It is shown that temperature and velocity of inducted air can be well controlled using Vitiated air heater system developed in this study, and we could make a Vitiated Air which is almost same with real air.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.11-11
• /
• 2000

액체렘제트 엔진에서는 고온·고속의 공기가 공기흡입구로 유입되기 때문에 고성능 램제트 연소기의 설계를 위하여 실제 비행조건을 모사할 수 있는 고온 고속의 공기 발샐장치가 필요하다. 본 연구에서는 수소연소에 의해 Vitiated Air를 발생시키도록 설계된 Vitiated Air Heater(VAH)를 제작하였으며, VAH의 성능평가를 통하여 80∼120m/s 와 400∼800K 범위에서 손쉽게 속도와 온도의 조절이 가능하고 균일한 속도 및 온도분포로 대기공기와 같은 Vitiated Air를 얻을 수 있었다. 그리고 VAH을 연결하여 Dump형 연소기의 특성을 실험하였다. 액체 램제트 엔진에 있어서 공기흡입구가 하나인 Dump형 연소기에 주요변수로서 흡입공기의 온도와 공연비를 변화시키면서 연소기내의 화염형상을 관찰하고, 온도분포를 계측하였으며 Injection 위치에 따른 화염현상을 관찰하였다. 각 경우의 연소효율을 계산하여 실험범위에서의 최적 연소조건을 제시하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.743-750
• /
• 2017

It is important to ensure a uniform temperature distribution in greenhouses for the mushroom cultivation. The air temperature of the mushroom cultivation greenhouse is made uniform by supplying a constant air temperature with the underground air. The mushroom cultivation array in a greenhouse in seven columns and four rows can make smooth air flows between the rows and prevent air differences between the top and bottom. The buoyancy effect in the entering air of 0.5m/s based on following density difference depending on initial internal temperature needs to be considered. The locations of the Fan Coil Unit (FCU) and fan were defined through flow analysis in a greenhouse to distribute the optimal uniform temperature. In this study, the air conditioning system of a greenhouse with a sandwich heat insulting panel shape which is composed of a FCU and fan was designed by flow analysis. A relatively uniform temperature distribution can be formed because the circulation path of air becomes longer in the different locations of the FCU (inlet) and fan (outlet) through the internal temperature and flow analysis. The cultivation and quality uniformity of the mushrooms could be promoted through these environmental improvements.