• 한국정밀공학회지
• /
• 제21권7호
• /
• pp.185-194
• /
• 2004

In order to analyze the motion errors of the aerostatic stage, it is necessary to consider the influence of the moment variation occurred inside the pads. In this paper, a motion error analysis method utilizing the transfer functions on the reaction force and moment is proposed, and general characteristics of the transfer functions are discussed. Calculated motion errors by the proposed method show good agreement with the ones calculated by Multi fad Method, which is considered the entire table as an analysis object. Also, by the introduction of the transfer function of motion errors, which represent the relationship between the spatial frequency components of the rail form error and motion errors, motional characteristics of the porous aerostatic stage can be generalized. In detail, the influence of the spatial frequencies is analyzed qualitatively, and the patterns of the insensitive frequencies which almost do not affect the linear motion error or angular motion error according to the rail length ratio and the number of the pad are verified. The relationship between the moment variation occurred inside the pads and the motion errors is also verified together.

• Tribology and Lubricants
• /
• 제7권2호
• /
• pp.13-21
• /
• 1991

선박은 사람이나 화물을 수상(水上) 운송수단의 목적으로 오랜 옛날부터 사용하여 왔으며, 금세기에 이르러서는 오랜 옛날부터 사용하여 왔으며, 금세기에 이르러서는 인류문화의 급속한 발전에 따라 주변생활이 가속화(Speed화), 합리화되어 문명의 혜택을 보다 많이 누리게 된 반면에, 국제간에 파생되는 여러가지 교환현상을 바탕으로 지구는 하나의 촌(村)으로 되어 유통경제를 지배하고 이용하는 운송수단으로 발전되어 왔다. 물질문명이 급속히 발전하는 작금, 선용추진 주 기관의 동향을 살펴보면, 1981년 세계에서 건조한 2000톤급 이상의 선박은 940여척으로 이중 13척이 증기 Turbine. 추진(推進), 나머지는 미끄럼 저속 디이젤 또는 중고속 디이젤 추진으로 되어있다. 이와 병행하여 선박에 쓰여지고 있는 각종 윤활제는 주기관으로서 디이젤 engine, Trubine engine, 가솔린 engine, 석유, engine, 선외기, 왕복동 증기기관, Journal계열로서 역전기, 추력베어링, 중간 베어링, 프로펠러베어링, 일반상선으 보조기계로서 발전기, 공기압축기, Boiler, 각종 Pump, 각종 Motor, 냉동기, 조타장치, Side Thrust, 갑판기계, 환기용 송풍기 및 통풍통, Oil 청정기, 수밀로(水蜜爐), 소화설비, 주기 개방용 천정 크레인, elevator, 어선으로서의 주 기관, 보조기기 등에 쓰여지고 있으며 이밖에 수중날개선 등에도 적용되는 등 실로 다양다종한 윤활제가 요구되고 있음에, 본 논고에서는 제목 건을 중심으로 한 선박과 윤활의 중요 Point만을 간추려 기술하고져 한다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.127-132
• /
• 1999

The inlet pressure build-up at the leading edge of bearings which have discontinuous lubrication surface is analyzed theoretically. The analyses of Inlet pressure build-up is obtained by means of full Navier-stokes equations. Beam-warming method is used to solve navier-stokes equations. The results show that inlet pressure is above atmosphere pressure in front of leading edge of hearing.

• Tribology and Lubricants
• /
• 제7권1호
• /
• pp.35-39
• /
• 1991

The performance of the ultra-precision machine tools depends on the steady state characteristics of the main spindle bearings. For excluding the effect of machining error with perpendicularity, conical or spherical bearing has been used. In this paper, steady analysis of the externally pressurized conical gas bearing for ultraprecision is carried out based on the direct numerical method with assumption of point source. As a result of theoretical analysis, design parameters for optimal condition of conical gas bearing are' presented in dimensionless form.

• Tribology and Lubricants
• /
• 제12권1호
• /
• pp.47-55
• /
• 1996

In this study, steady state and perturbed pressures are experimentally measured under inherently compensated restrictors in externally pressurized air bearings. A piezo actuator is used for simulating small displacement perturbation in the air film. The pressures under the restrictors are measured by a miniature type pressure transducer and the height of the air film is measured by capacitance type gap sensors developed by Chapman's method. The perturbed pressure is obtained through Fourier transformation of the two signals. The measured perturbed pressures are in good agreement with the calculated values.

• Tribology and Lubricants
• /
• 제7권2호
• /
• pp.51-60
• /
• 1991

For the accurate run-out of a light rotor shaft the sliding bearings supplied with externally pressurized air are effectively applied, and it is important to predict the static and dynamic characteristics of rotor-bearing system. In this study direct numerical method is applied to solve the perturbed Reynolds' equation. To solve it the perturbed dimensionless mass flow rate is used as the boundary condition under the inherently-compensated restrictor. The dynamic characteristics of a rotor supported in the externally pressurized air bearings are analyzed, and as a result the orbit of the journal center is calculated. The theoretical results are investigated and discussed.

• Tribology and Lubricants
• /
• 제13권4호
• /
• pp.40-46
• /
• 1997

The externally pressurized air journal bearings which have two circumferential grooves with inherently compensated restrictors are analyzed. Two circumferential grooves with restrictors are made on the bearing surface in order to increase the stiffness and damping coefficients. In this paper, the dynamic characteristics such as stiffness and damping coefficients of this type of bearings are calculated. As a result of theoretical analysis, it is verified that there exist the groove depth and the distance between two grooves which generate the maximum stiffness at the given bearing dimensions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.137-138
• /
• 2006

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.1117-1121
• /
• 2001

The dynamic behavior of slider is investigated using Dynamic Flying Height Tester(DFHT). The dependence of slider's dynamic fluctuation on disk velocity is measured, and a comparison is made with the computational result.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1993년도 제18회 학술대회 초록집
• /
• pp.51-56
• /
• 1993

The conical bearing can be used to support the radial and thrust load simultaneously. Two circumferential grooves with discrete hole restrictions are made on the bearing surface in order to increase stiffness. In this paper, the dynamic characteristics of this type of bearings are calculated such as stiffness and champing coefficients. As a results of theoretical analysis, it is verified that there exist the groove depth and distance between two grooves which produce the maximum stiffness at the given bearing dimensions.