• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.533-537
• /
• 2003

Compared to sintered polycrystalline diamond (PCD), the deposited thin film diamond has a great advantage on the fabrication of cutting tools with complex geometries such as drills. Because of high performance in high speed machining non-ferrous difficult-to-cut materials in the field of automobiles industry, aeronautics and astronautics industry, diamond-coated drills find large potentialities in commercial applications. However, the poor adhesion of the diamond film on the substrate and high surface roughness of the drill flute adversely affect the tool lift and machining quality and they become the main technical barriers for the successful development and commercialization of diamond-coated drills. In this paper, diamond thin films were deposited on the commercial WC-Co based drills by the electron aided hot filament chemical vapor deposition (EACVD). A new multiple coating technology based on changing gas pressure in different process stages was developed. The large triangular faceted diamond grains may have great contribution to the adhesive strength between the film and the substrate, and the overlapping ball like blocks consisted of nanometer sized diamond crystals may contribute much to the very low roughness of diamond film. Adhesive strength and quality of diamond film were evaluated by scanning electron microscope (SEM), atomic force microscope (AFM), Raman spectrum and drilling experiments. The ring-block tribological experiments were also conducted and the results revealed that the friction coefficient increased with the surface roughness of the diamond film. From a practical viewpoint, the cutting performances of diamond-coated drills were studied by drilling the SiC particles reinforced aluminum-matrix composite. The good adhesive strength and low surface roughness of flute were proved to be beneficial to the good chip evacuation and the decrease of thrust and consequently led to a prolonged tool lift and an improved machining quality. The wear mechanism of diamond-coated drills is the abrasive mechanical attrition.

• Composites Research
• /
• v.21 no.3
• /
• pp.9-17
• /
• 2008

In this paper, the low velocity impact characteristics of filament winding CFRP pressure vessel was investigated using numerical and experimental methods. The cylinder part of CFRP vessel was impacted using triangular shape impactor which simulated the sharp edge of dropping tools and impact response behavior of CFRP was reviewed. The mechanical behavior, such as deformation and stress distribution, were also predicted by explicit finite element method and the validity of the model was investigated. For the quantitative evaluation of the residual strength of the pressure vessel after impact, a series of the ring specimens was cut from the impacted vessel and its burst pressure was measured by hydraulic pressure hoop tension test. As the results, the relationship between the residual strength degradation and the impact energy was successively obtained and a useful methodology to evaluate quantitatively the impact damage tolerance of CFRP pressure vessel was established.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.478-478
• /
• 2021

전 세계적으로 많은 나라들이 기후변화에 적응하기 위해 수자원 관리 전략을 마련하고 있으며, 수자원의 근간이 되는 빗물의 효율적 사용을 위해 우리나라에서도 빗물이용시설이 많이 도입되고 있다. 본 연구에서는 사용자 편의 환경(graphical user interface; GUI)을 갖춘 빗물이용시설의 용량 결정 프로그램(capacity design aid for rainwater harvesting; CARAH)을 개발하여 관련 연구와 업무에 활용성을 높이고자 하였다. CARAH는 저수지 질량 보존식과 python의 pyswarm package에 탑재된 메타 휴리스틱 방법 중 하나인 입자 군집 최적화(particle swarm optimization; PSO) 기법을 연계하여 빗물이용시설의 최적 용량을 짧은 시간에 결정될 수 있도록 개발되었다. 그리고, C#의 Windows Forms Application을 이용하여 사용자 편의 환경을 구현하였다. CARAH의 입력 자료는 모의 기간, 유입량, 목표공급량, 공급보장률이고, 출력 자료는 공급보장률-저류조용량, 목표공급량-실공급량-미달성량, 저류용량-유입량-실공급량이다. 빗물이용시설 계획에 필요한 여러 입력 자료를 쉽게 입력할 수 있도록 구현하였고, 그래프와 표의 형태로 계산된 결과를 화면에 직접 표출함으로써 사용자가 직관적으로 확인할 수 있도록 하였다. 한편, 입·출력 자료를 포함한 분석 결과는 파일로 관리할 수 있도록 기능을 갖추어 수정 및 보완 등의 반복적 활용이 가능하도록 하였다. 개발된 프로그램의 활용성을 검토하기 위해 실제 저류지가 설계된 인천의 청라지구 1공구를 대상으로 적용하였고, 분석 결과의 적절성을 확인하였다. 본 연구에서 개발된 CARAH는 빗물이용시설의 용량 결정에 관한 효율을 높일 수 있는 프로그램이고, 누구나 쉽고 간편하게 사용할 수 있는 프로그램으로서 향후 활용성이 높을 것으로 판단된다.

• Korean Journal of Environment and Ecology
• /
• v.22 no.1
• /
• pp.18-34
• /
• 2008

Based on external morphology, each of five species can be classified into three groups: 1) B. falcatum group (B. falcatum, B. scorzonerifolium), 2) B. euphorbioides group (B. euphorbioides) and 3) B. longiradiatum group (B. longiradiatum, B. latissimum). B. falcatum group has cauline leaves linear or lanceolate in shape and attenuate at base and not surrounding the stem. In contrast, B. longiradiatum group and B. euphorbioides group have cauline leaves ovate, lanceolate or panduriform in shape and auriculate or cordate at base and completely surrounding the stem. The inflorescence is basically compound umbels terminated at the apex of stem. But B. euphorbioides group is small in size and pedicels are rather short and the number of the pedicel is ca. 20. On the other hand, B. longiradiatum and B. falcatum groups are large in size and their pedicels are long and the number of the pedicel is around 10. The pore of pollen aperture of B. longiradiatum and B. latissimum is partially projected or not while those of B. falcatum group and B. euphorbioides is usually remarkably projected. The number of somatic chromosomes was counted as 2n=20 in B. falcatum, 2n=12 in B. scorzonerifolium and B. longiradiatum, and 2n=16 in B. euphorbioides and B. latissimum. Although chromosome numbers of B. euphorbioides and B. latissimum are the same, the two species are not likely to relate because the karyotypes of the two species are different from each other. Based on these observations, it can be concluded that B. latissimum is most closely related to B. longiradiatum. However, molecular data indicated that the species is probably related to B. bicaule distributed in central Siberia. In terms of conservation of B. latissimum, overexploitation by human and grazing by goat are most threatened factors.

• Journal of Practical Engineering Education
• /
• v.15 no.1
• /
• pp.119-126
• /
• 2023

Today, in order to improve fuel efficiency and dynamic behavior of automobiles, an era of light weight and simplification of automobile parts is being formed. In order to simplify and design and manufacture the shape of the product, various components are integrated. For example, in order to commercialize three products into one product, product processing is occurring to a very narrow area. In the case of existing parts, precision die casting or casting production is used for processing convenience, and the multi-piece method requires a lot of processes and reduces the precision and strength of the parts. It is very advantageous to manufacture integrally to simplify the processing air and secure the strength of the parts, but if a deep and narrow pocket part needs to be processed, it cannot be processed with the equipment's own spindle. To solve a problem, research on cutting processing is being actively conducted, and multi-axis composite processing technology not only solves this problem. It has many advantages, such as being able to cut into composite shapes that have been difficult to flexibly cut through various processes with one machine tool so far. However, the reality is that expensive equipment increases manufacturing costs and lacks engineers who can operate the machine. In the five-axis cutting processing machine, when producing products with deep and narrow sections, the cycle time increases in product production due to the indirectness of tools, and many problems occur in processing. Therefore, dedicated machine tools and multi-axis composite machines should be used. Alternatively, an angle spindle may be used as a special tool capable of multi-axis composite machining of five or more axes in a three-axis machining center. Various and continuous studies are needed in areas such as processing vibration absorption, low heat generation and operational stability, excellent dimensional stability, and strength securing by using the angle spindle.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.13 no.1
• /
• pp.2191-2205
• /
• 1971

In this research, Nong-rim No. 6 was adopted as a test variety of rice. Rice seedlings were transplanted on June 14, 1970. Roots were settled into soil on June 20 and a total number of days irrigated of $21cm{\times}21cm$ and an area of $9.9m^2$ for a test plot were accepted, planting 70 stumps of rice in a test plot. The soil in test plots are classified by soil test as oam, and its chemical contents are as shown in Table 3. Irrigation water was secured by pumping from the Sudun stream that originates at the Suho reservoir. Accordingly, the qualities of irrigation. water are considered to be the same as those of water stored in the Suho reservoir. There were 54 days of intermittent rainfalls in total during the whole 110-day period of irrigation. As a result, it is likely that the growth of rice plants was influenced by rainfall at a comparatively great degree. In order to measure the amounts of water consumption, infiltrometers, measuring devices for the decreases of water depths and lycimeters were provided. As a result of measurements, an average daily rate of infiltration was observed to be 14mm/day. It is expected from this research that the effect of increased yield will be secured by supplying optimum amounts of water for irrigation on proper times, and that the amounts of water consumption for irrigation can be saved by applying suitable irrigation methods. The test results obtained are summarized as follows: 1. Yields produced in the test plots of continuous irrigation are lower than those in the test plots of rotational irrigation, i.e., yields produced at the test plots irrigatied once in a period of 8 days are higher by 27% in average than those produced at test plots of continuous irrigation. 2. The amounts of irrigation water for test plots, which have a clay layer of 9cm in thickness and vynil diaphragm without holes, are saved by about 52% in comparison with ordinary test plots. 3. Ears are sprouted 5 days earlier at continuous irrigation plots as compared with other test plots. 4. It seems that there are growing stages of rice plants such as those of forming and sprouting of ears, in which the amounts of irrigation water are consumed more in comparison with the other stages. Therefore, it may be possible to increase of decrease the amount of irrigation water, according to the growing stage of rice plant, so as to save irrigation water.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.22 no.4
• /
• pp.373-382
• /
• 2000

Individual genetic susceptibilities to cancers may result from several factors including differences in xenobiotics metabolism to chemical carcinogens, DNA repair, altered oncogenes and suppressor genes, and environmental carcinogen exposures. Among them, genetic polymorphisms of metabolizing enzymes to chemical carcinogens have been recognized as a major important host factors in human cancers. They have two main types of enzymes: the phase I cytochrome P-450 mediating enzymes (CYPs) and phase II conjugating enzymes. The purpose of this study is to determine the frequencies of genotypes of phase I (CYP1A1 and CYP2E1) and phase II (NAT2) metabolizing enzymes in healthy control and head and neck cancer patients of Korean and to identify the relative high risk genotypes of these metabolizing enzymes to head and neck cancer in Korean. The author has analyzed 132 head and neck cancer patients and 113 healthy controls using polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP). The results were as following; 1. The frequencies of genotypes of CYP1A1, CYP2E1 and NAT2 in healthy control were as following; CYP1A1 exon 7 polymorphism; Ile/Ile: Ile/Val: Val/Val = 59.3%: 36.3%: 4.4% CYP2E1 Pst I polymorphism, C1/C1: C1/C2: C2/C2 = 61.1%: 32.1%: 6.2% NAT2 polymorphism; F/F: F/S: S/S = 43.4%: 48.7%: 8.0% 2. In analysis of phase I enzyme, Val/Val genotype in CYP1A1 exon 7 polymorphism and C2/C2 genotype in CYP2E1 Pst I polymorphism were associated with relative high risks to head and neck cancers (Odds' ratio: 2.09 and 1.37, respectively). 3. Among the genotypes of NAT2 enzyme polymorphism, S/S genotype of NAT2 enzyme had 1.03 times of relative risk to head and neck cancers. 4. In combined genotyping of CYP1A1, CYP2E1, and NAT2 enzymes polymorphisms, the patients with Val/Val and C1/C1, C2/C2 and fast acetylator, and Val/Val and fast acetylator had higher relative risks than the patients with each baseline of combined genotypes (Odds' ratio: 2.82, 1.98 and 2.1, respectively). These results suggest the combined genotypes of Val/Val and C1/C1, C2/C2 and fast acetylator, and Val/Val and fast acetylator were more susceptible to head and neck cancers in Korean. And genotyping of metabolizing enzymes could be useful for predicting individual susceptibility to head and neck cancer.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.9
• /
• pp.61-67
• /
• 2017

Research into the selection of suitable materials and the development of fast processing methods for press die manufacturing is absolutely necessary to reduce the production time and cost. In particular, knowledge of its heat properties must be considered whendeveloping a long press die. Generally, as the main component materials of press dies, Cr, W low alloy tool steel, high carbon-high chrome steel, high speed steel, etc., are used as thetooling steel for the cold die. Machine tools and wire-cut electric discharge machining are mainly used for processing the press die parts. There are many differences in the machining time and life cycle of die parts depending on the machining process. The parts produced by milling and grinding have a high manufacturing time and cost with a long life cycle, while thosemade by milling and wire-cut discharge machining have areduced manufacturing time and cost,whereastheir die life cycle is reduced. Therefore, in this study, we will discuss amethod of improving the life cycle of the die parts by using heat treatment as a processing method that reduces the manufacturing time and cost. SEM, EDS analysis and the surface roughness analysis of the surface and center of the workpiece are used for analyzing the specimens produced by three machining methods, viz. milling - grinding, milling - wire cut discharge, and milling - wire cut discharge - heat treatment. A method of making die parts having the same life cycle as those produced by milling - grinding is developed with the milling - wire cut discharge - high temperature tempering method.

• Korean Journal of Environmental Biology
• /
• v.33 no.2
• /
• pp.256-261
• /
• 2015

This study was conducted to assess the influence of hazard pattern in the surface structure of pollen grains of Campsis grandiflora, and cytotoxicity of different part extracts and nectar on RAW264.7 macrophages. The pollen grains were medium sized ($21.8{\mu}m$) with tricolpate aperture type. In equatorial view, the pollens were prolate (P/E=1.8) and the exine pattern was smooth and reticulate. This result contradict with the rumor of having a hook-shaped protuberance that can damage the cornea because we couldn't observed any protuberance on the surface of the outer wall. Furthermore, we investigated the 70% MeOH extracts (flower, leaf, stem) and nectar of C. grandiflora for their cell viability in temporal basis via MTT analysis on RAW264.7 macrophage cells. There was no significant difference in the cytotoxicity among the MeOH extracts and nectar of C. grandiflora after 24 h. However, nectar showed the dosedependent cytotoxicity on RAW264.7 macrophage cells after 48 h.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.742-748
• /
• 1997

Diamond films which have high hardness and thermal conductivity can be used to improve the performance of WC-Co as a cutting tool material. However, it is difficult to get such coatings of good uniformity and adhesiveness due to the surface characteristics of WC-Co. To get better coatings, some techniques, such as the surface treatment of substrate or the formation of interlayer between substrate and diamond film, have been tried. In the present work, the nickel interlayer is formed onto WC-Co by electroless Ni-P plating, which is introduced as a new method, and then diamond film is deposited on the interlayer. Formation and uniformity of three layers, i.e., substrate, electroless plate, and diamond film, and the adhesiveness of interlayers were studied. To investigate the effects of pretreatment on electroless plating, two different methods such as acid treatment and diamond powder treatment were used. The effects of heat treatment of the electroless plated surface on adhesiveness between the substrate and the interlayer were examined. It was found that as the temperature increases, the Ni crystals grow and then result in improved adhesiveness. Diamond film coatings of pure diamond phase were obtained at $800^{\circ}C$. It is concluded that the heat treated electroless Ni-P plating can be effectively used as a interlayer between WC-Co substrate and diamond film.